Your video is waaaay better than the installation instructions that come with the fan. Thanks!

Left out some very important steps!

Great video. It really helped at least confirm what I thought the instructions were attempting to convey. The one piece that maybe was not caught on video was using 2 of the long screws to secure the adapter to the ez bracket before pushing the fan unit into place. Thanks for the video.

Thanks! I report success!!! The biggest challenges were the screws from the old supports were wildly angled downward, making it difficult to get anything into them except for my handy vampliers. Getting the fan box to snap into the electric junction box/ventilation hose "smaller section" was much more difficult than I imagined. Part of my problem was that the previous fan width was about 1/4 inch larger than the Panasonic, so the smaller section's bottom lip wouldn't stay firmly below the ceiling sheetrock, it just kept scooching up, preventing the happy click of section mating. My solution was to use a pair of washers around the screws that go on the smaller section side so the screws wouldn't travel up through the extra wide fan box section screw slots (I have no idea why they made them so wide and long...) As the screws tightened, the washers held firm from below and the screws pulled the small section down until the happy click occurred. I also discovered in my first try at this that if there's no "click" then there will be a high volume of air escaping into the attic, likely moist bathroom air. That click is crucial!

You skipped the part that I am struggling with - installing the adapter to the Flex-X bracket with two self-drilling screws! ... when following the diagram instructions, the screws don't hold the two together.

Multiple people have replied correctly that this install was not 100% correct. I have done this twice with this unit. Once in my unfinished basement and one as a replacement in my master bath. I did have access to the attic for my master bath which was helpful. Because of the rat runs and trusses that were in the way, I had to add a metal 90 degree elbow up, then add the 4" to 3" reducer and then attach the 3" flex duct. For the drywall, I only cut a hole the size of the fan box itself. With the EZ flex bracket, one direction is already set for you. There was no exposed brackets. The drywall covered them, which also helps to bear the weight load of the fan. Screw in your brackets to your joists/trusses. Make sure they are square. Once you have connected the wiring and duct to the removable junction box, that part gets screwed into the flex bracket. However, the L portion lays (wraps) on the drywall and you screw through the L, drywall and then into the bracket which is on the other side of the drywall. If you do not do it this way, then the fan unit will NOT seat fully into the junction box. Once seated fully, the four flanges of the fan housing should be flush to the drywall, you screw in the last two screws, put in the small machine screw and plug in the electrical quick connect and you are good. That machine screw helps to hold the housing into the junction box portion which is screwed into the flex bracket. If you have some gaps between the flange and drywall, just hit with a bead of caulk so everything is sealed. You won't see it because of the plastic finish piece. I agree that both the written instructions and pictures are lacking.

@gz6915

2 ай бұрын

One question: if we need to replace the fan in the future, it would be a hard job as the whole fan site on top of the drywall. There is no way to take it out without cutting the drywall. Is it correct?

Is this a joke? What seems to be the most important and most difficult step is the installation of the junction box/duct collar and then bringing the fan unit into the bracket and connecting the fan assembly to the Junction box bracket. He cannot get to it from above, just from below. How did he connect the two assemblies. I don't think he did.

@RudyNortz

Жыл бұрын

I think you are right. This vid skipped the hard parts.

@choski76

3 ай бұрын

How can he undo it if it needs a fix?

@razmspiele25

2 ай бұрын

This guy skips that step, another video the guy claims he thought his phone was recording and it wasn’t at the same part. Insane.

@ArcConAK

16 күн бұрын

Im guessing he taped the flex duct to whatever duct was in the ceiling but that flex all cramped up there is dog shit. Sure it’s just a bath fan but lint will slowly accumulate in those ribs and cramped angle he created. Pro hvac guys never use a single piece of 4” flex unless they’re total hacks.

Do you know if Panasonic's smaller "Whisper Boost" from Home Depot is as easy to install? I haven't found a a good video or instructions & their manual just seems to show install on open ceiling joists :(

Can you recommend a fan for a kitchen ? I need a new exhaust fan for my kitchen to draw out cooking smells…

My current cutout is in circular with 290mm in dia, do I still about to install this fan?

Think know now What I did wrong I had the fan primary fan part, placed on top of the bracket instead of on the underside outside of the drywall

You have installed the adapter incorrectly. It comes under the drywall not under the flex bracket.

@FrancisDGM

5 ай бұрын

At what time of the video is that? Just want to be sure I'll install mine this week.

@blueststar4u

5 ай бұрын

​@@FrancisDGMtime @ 3:50 the bottom lip should be under the drywall.

can you install this fan in the kitchen? if it has a vent that's roughly the same size?

You don't show the wiring

Would like to know where to connect the motion censor, the instruction manual doesn't say how

my ceiling is a plaster with wire mesh construction from the early 1960s. The current fan in there is a straight shot to the roof. Guess it's called an "inline" exhaust fan. There is no hose tubing etc - it's basically a round cylinder of sheet metal that goes from the fan through the air space to a covered vent. I'm still trying to wrap my head around how to install a new generation fan into that spot>!!?

@millersfloorcoatings

2 ай бұрын

You'll be way better off with your old straight shot sheet metal ductwork than the flexible plastic duct. The sheet metal is smooth walled and less resistance and will work much better. Definitely utilize the existing ductwork. You will figure it out or find someone that can help you. It basically comes down to having the right tools, time, and patience. I just installed one of these in my upstairs bathroom in a 1917 house. Had to design and build my own galvanized 4" duct work all the way to the gable wall on the back of my house. Took a lot of time but finally got it all roughed in and connected tonight and it works. Had to insulate the duct work as well because I live in Northern MN. What a project!! I had the tools and the time though, so I saved a lot versus finding a contractor to do the job. Kind of a fun challenge.

Mine didn’t come with a 3” to 4” reducer, which I needed. Also, the bracket was a pain to install with 3/4”strapping between the drywall and the joists so I had to add some blocking. I wish they had designed it to be more user friendly for that situation, which is pretty much the norm here in the northeast.

@cengeb

6 ай бұрын

they have several models, ya need to get the retrofit models, comes with plastic slip on reducer and flex bracket. I installed 3 to replace the old Broan cement grinders...Panasonic is the way to go in bathroom vent fans

@captainamerica9725

4 ай бұрын

I’m a builder here in the northeast. Wait is the 3/4” strapping not a thing elsewhere? Does everyone else just go right to the joists? I was wondering how the hell they didn’t account for this.

I have the Panasonic RG-R811A whisper remodel exhaust fan. Does the Panasonic RG-R811A bathroom exhaust fan have a moisture sensor to automatically place it in standby mode when no moisture is present? Also, which switch is recommended, a timer switch or a regular switch, and which make and model of switch for both? Thanks.

@karthikp5300

7 ай бұрын

Wishper Renew Model #RG-N110LHA have the moisture sensor. Since your RG-R811A doesn't have sensor you may have to use a timer switch

What an excellent, informative video. Thank you so very much for taking the time to make this video :-)

For some reason, he left out the step where the adaptor (the part to which he connected the wiring) gets connected to the Flex-Z-fast frame, which is absolutely critical. It will never work without doing that. Fortunately, someone made a brief comment about the missing step, and I watched another video to show how that gets installed.

@tylerchromicz5870

11 ай бұрын

What is that video?

My fan turns on off in intervals. Is it normal?

Am I mistaken or was there a quick cut to a man with no sheetrock covering his joists, then a cut bsck to this installation?

The only way that this would have worked is if he cut the existing rigid duct back to allow the flex to bend without restricting the flow. Why didn’t he show that?

What if you have a plaster ceiling? would screws hold on the edge of the plaster?

@bkulber1

9 ай бұрын

I just installed this model yesterday. The screws actually go through the ceiling and into the "Z-fit frame"...which is screwed into joists. What your ceiling is made of should be irrelevant. That being said, there are 4 supplied screws, but 8 screw holes in housing tabs. I'm not sure what the strategy for that was.

@michaelpolsinelli2345

9 ай бұрын

@@bkulber1 yep, you're right. I got mine installed about 6 weeks ago. It went in really easy.

I installed this fan my biggest complaint is that I had a hard time installing the face plate where the ducting goes. I tried to snap it together where these plastic pin guides supposedly holds it in place but these little plastics keep falling off. And the lid covering for the duct does not fit I couldn’t put it on because the dry wall is in the way. I don’t know how people are able to close the face plate because it won’t fit it sticks up over an inch and won’t close not unless I rip about 2 or 3 inches of the drywall but now I’m gonna have a giant whole that measures 3 inches by 10 1/2 inches, I think the engineers forgot about the lid cover and the dry wall. There is no way to close it. So I had to literally make holes on my ceiling and leaving it paper thin, now I have to use drywall patching I almost gave up with all the frustration. What were they thinking! Has anyone encountered this problem?

Sure; but try doing it in a old lathe and paster ceiling ? How do you accommodate for the ceiling that’s over an inch thick ? The main fan housing doesn’t slide up far enough to be able to connect the power plug in . That what I’m trying to do .

@swan7654

11 ай бұрын

I'm worrying about the same thing my house has new ceiling layered over old and is prob 2 1/2 to 3 inch thick...worried that the vent air outlet won't sit high enough to connect ...no fan installed there either 😢

@robertthurston6858

11 ай бұрын

I figured out what I did wrong. The flange of first part of the fan where the output vent is on , needs to be on the outside of the ceiling (Drywall/ Paster). But if your ceiling is really thick ,I don't think it's going to work at all. You're going to have to reduce the thickness of the ceiling where the fan is going to be mounted. Probably the inside layer of ceiling . Try and get it down so it only an inch thick. And then you will probably need to frame a subframe of wood, so the mounting bracket can be secured it. A lot of carpentry is about improvising. This not a quick job, try to be patient. Good Luck 👍

@stephengribble5997

9 ай бұрын

Yeah it's a stupid fucking design. I also have three layers of drywall for my bath ceiling in this 100 year old house. I had to cut out the inner two layers of Sheetrock so that the part with jbox and fan outlet would fit since there is only like 3/4 of space between the flange and the bottom of the outlet. Then I had to add some blocking so that the z flex thing had something to screw into. Huge pain in the ass. Poor design if you've got an older house to work around.

@WakandaBabe

7 ай бұрын

I just had this installed in my plaster ceiling. I actually worried about doing it but the installer had no problems and the fan works just fine. There was no fan previously.

The Old Bathroom Fan Was A Nutone Basic Bathroom Fan

Tim Heidecker does remodel? Times are tough...

Good video--it all works. However, like many other installers, he did not follow the installation instructions which say to secure the Adaptor to the Flex-Z-Fast unit BEFORE installing the fan body. YMMV.

@frankcanuck360

Жыл бұрын

Yep noticed the same thing

@christhornton468

Жыл бұрын

Agreed...are there holes for the long screws or do you just screw through the slit on the bracket and then through the metal on the adaptor?

@thomaswhite4527

Жыл бұрын

@@christhornton468 You may wish to look at another installation video. Most of the instructions show two self-drilling screws through the holes in the lip of the unit that go through the drywall and into the Flex-Z-Fast bracket already installed. I think that is what you said in your comment, too.

Why would anyone choose the 80 CFM over the 110 CFM? I would think you would want the most suction power.

@bkulber1

9 ай бұрын

I think it's going to depend on your duct work. If you have 3" or even 4", you may want 80. I installed this with 4" duct work and I had a lot of air pushing through the seams of the unit when I had it set to 110. Something you don't want in northern climates. I put foil tape on all the seams which did the trick, but I would imagine most people won't think of that. Also, you pretty much cannot hear it at all when it's at 80, but when it's at 110, you can hear it, but it's still no doubt much quieter than what you're replacing.

@EIiasNI

3 ай бұрын

110 CFM is better but louder. That's the main difference

Does it need to be connected to a switch?

@pdxfunkjunkie

8 ай бұрын

@robcoviello5383, your question is a month old, so maybe you have already sorted this out. In this video, the installer just re-used the existing switch (or timer) that was already at the other end of that electrical wire. NEC code now requires a TIMER, not a switch. I guess the timer is safer - in case you forget to turn off the switch - but honestly it's also WAY more convenient. Set it and forget it.

Good video but didn't show the wiring which is what I really needed to see.

@pauliesev6

Жыл бұрын

You don’t know how to match colors?

@RudyNortz

Жыл бұрын

Black to Black, white to white, green to green

4:29 Theres a crucial step that was skipped. Its not hard to see what though

Shouldn't insulated duct be used?

@ScottPetersGuitar

2 ай бұрын

Yes. To eliminate risk of condensation. Especially in cold markets.

Video shows the easy steps. He must have hired someone to do the hard parts.

@RudyNortz

Жыл бұрын

Exactly. I put this fan in today and it ain't as easy as this. To get this to fit you need to have no drywall material between those rails and the flange on the fan assembly. Watch a video on an installation of the fan in a new house (no sheetrock) to see how it should go.

The dude completely ignores talking about how he removed the original duct and then reattaches the new duct… weird

@bkulber1

9 ай бұрын

I installed one of these yesterday. I never want to talk about replacing the duct work ever again either. ;) What a nightmare.

The instructions for this product are vague, with conflicting images concerning the adapter as installed to the bracket. This video basically skipped that part too. UGH.

@RudyNortz

Жыл бұрын

Right, the instructions are not clear.

@bkulber1

9 ай бұрын

Oh, you mean how the product comes with 8 holes on the body, but there are only 4 screws? LOL! So strange. I just used logic to install it. If the frame is screwed to the joist, just screw the unit to the part of the frame that is closest to the part that is screwed to the joist. That's more than enough to support the weight of this unit.

Super helpful. The instructions it comes with are garbage

DID IT WRONG 😂

Flex duct is not allowed in California...!

@morganpay

Жыл бұрын

Yeah, and everything in California causes cancer. Meanwhile, in the other *rational 49 states*....

@MrKillerRC

Жыл бұрын

California blows.

@bubunelu7027

9 ай бұрын

Then you either move out of California or just install it and don't tell nobody 😂

Useless. Covered up the wiring crucial part.

Liar. He skipped important steps.😂

This is the worst video I have ever seen I've been a contractor for 40 years and this is not helpful I can't imagine a homeowner trying to do this without any background

Great video? No, it is not. This didn't answer any of my questions about how the pieces fit together. And when connecting the wiring, the housing was in the way so couldn't see anything. I learned nothing from this. Downvoted.

You're supposed to be a licensed electrician to do anything professionally higher than 10 volts.

@cengeb

5 ай бұрын

wrong, there are exceptions. You think siding guys are what now?

Kinda a dumb video!

Delete this bro