What DFAM tips do ya'll want us to cover in a future episode? Shout out below!

@williammurphy3273

11 ай бұрын

How can we fuse onyx parts with PLA parts, where a bucket shape has been designed to nest inside another! (but half is onyx and a half is PLA? Glueing?

I'm not a fan of press in inserts. My go to is to create a hex cavity, erase the support material, create a pause statement at the top of the cavity, drop in a real nut of any material you choose, continuing printing for a fully embedded piece of hardware that is guaranteed to not pull out or spin. A video on that procedure would be equally as beneficial. Your thoughts??

@markforged

Жыл бұрын

Very clever! And thank you for the idea for an upcoming video. 💪

@volkhen0

Жыл бұрын

Even better is rectangle nut as from my experience hex nut can sometimes spin inside the cavity if the force is too big. With rectangle nut - no chance. Plus the front area is bigger so it’s more difficult to pull it.

@markforged

Жыл бұрын

Oh yeah! Nice one Mariusz -- thanks for watching and for the tip!

@Henry_Swanson

10 ай бұрын

@@volkhen0 Prusa uses rectangular nuts in their machine, and there's no need to pause the print to put them in. You can have the customer do it with needle nose pliers while cursing.

@freetobe3

3 ай бұрын

@@volkhen0 what about adding a dab of epoxy to the sides of the squared/rectangular nut so it fills and solidifies any remaining gaps in the cavity? or useless?

Great guide, answered a lot of my questions! The only thing i am unsure about is the 1:46 part. Are those holes bigger than the screw's biggest outer diameter or will the screw actually touch these walls? I am using m2 screws, what diameter should this part be?

Where do I find the datasheet ? I tried this 2 years zog .. but wrong :D the filament came back into the insert render it useless. But I did not know about the datasheet :D

2:27 you took 5.74mm from the data sheet but that's called out as the minimum material thickness, not the hole diameter. Two lines below that is the hole diameter you should have used, 0.221" (5.61mm).

@AustinVojta

Жыл бұрын

You're totally right, good catch.

@markforged

Жыл бұрын

Good catch Tort! And thanks for letting us know.

@stephenbarlin2314

6 ай бұрын

Don’t forget to add the diameter of the print nozzle to get an accurate hole on a 3 d printed part.

@johannd1100

5 ай бұрын

@@stephenbarlin2314 So if I'm using a 0.4mm nozzle then all my walls would bulge out a minimum of 0.2mm from each direction?

@cryora

Ай бұрын

In practice, the exact hole dimension isn't too critical, unless you're going for optimum strength and alignment, which you might not necessarily need for your application. Heatsets are remarkably strong. There is a video of a guy who put his full body weight to pull against it and it still held up. Depending on your design, your part would break before the insert pulls out. Most through holes and slots are designed to be oversized for the screw you will use, so that gives you extra leeway. Just like you wouldn't specify all your tolerances to 1 mil, you don't need everything to be perfect. Sometimes, you just need to get the job done.

Nice

@markforged

Жыл бұрын

You are! Thanks for watching, Tan

The temperature seems very high. I find if I use high temps the insert will not centre easily and the central screw hole fills with plastic so you cannot screw in the screw. Someone else where suggested the temperature should not exceed the plastic phase of the material. This allows the insert to be inserted accurately without material being squeezed into the threaded part. I use inserts mainly when the part needs to be undone frequently. ( e.g. battery lid fastening).

@RestoreTechnique

5 ай бұрын

Yeah I thought so too. I have the same soldering iron as him, and I set it to 200C, and it goes in quicker than shown.

@Vladamyr

5 ай бұрын

Ruined quite a few attempts from his 50 degrees over and then setting his iron to 180 more than the melting point. Then, no mention about rendering the insert useless because it's full of plastic.

Where can I find a data sheet? That tells me what size hole I need for what insert. I've been looking and I cannot find one. Can somebody please help me

@markforged

5 ай бұрын

The data sheet can be found from the manufacturer or reseller of whatever size screws and inserts you buy. We purchased ours from McMaster and pulled the data from them.

I think there is a mistake in the tips, it should be: Set soldering iron 50-100 °C BELOW temperature of printer nozzle. Also note that there are inserts with some lips that provide much more pulling resistance, even more than nuts.

You ignored the spec sheet callout for an 8° taper in the hole. A straight hole is adequate, but for optimum pull out and torsional strength the 8° taper is important.

@markforged

Жыл бұрын

Great call out, Robert. We'll be sure to include details like that in future videos.

@Henry_Swanson

10 ай бұрын

If the hole tapers 8° is the diameter called out the major or minor dimension?

@cryora

Ай бұрын

Spec sheet is a guide, not a rule. You don't always need the maximum strength, and can get away with different dimensions. There is a video where a guy tested heatset inserts for a range of hole diameters, and most of them held up quite strong. Just expect to experiment around to find one that works for you, as it might not work the first few times. 3D printing is about experimentation after all, not blindly following rules.

@thomast7748

15 күн бұрын

thank you for your comment, I took good note of that.

Could skip the finger snapping, but otherwise good.

@markforged

9 ай бұрын

Thanks for the comment, Colin!

Да ладно, прям вот так и ставят их?