DUDE...your video was the only one that had the same exact wiring as mine. It was actually quite helpful to me. Appreciate your time and for sharing! 👍

@arpvisuals

Жыл бұрын

I'm glad it was helpful! Thank you!

I have a GV70 and was going to do mine, but one thing I don’t like is that you see the individual led lights (dots). In all the ads, I never see that. So I’m on the fence weather or not I’m gonna do it. I first want to see it done on a GV70 first. But hats off to you for getting it done.

@isaiahbledsoe257

Жыл бұрын

might just be the camera or the version he boguht cause i saw a dude do it with his truck and it looked exactly like the ads not paid promotion or anything

@lucarvian

7 ай бұрын

Yeah, same here. Looks cheap with individual leds, and the colour looks bluish and doesnn't match the OEM led. Probably about 6000K color temp vs the 4500K that most vehicle LEDs are. Looks too aftermarket, cheap IMHO.

interesting nice color of the car

The two yellow wires you will need to splice into your DTR left and right. This way the light bar will work with your blinkers as well!

Yellow is for turn signal connection I believe

@chrissullivan4530

Жыл бұрын

Mine came with 2 yellow so would one be for left and right? There are no instructions 🤷‍♂️

@darksteelhelm

Жыл бұрын

Yes

Accessory fuse may be located in the car itself, by your feet on driver side

@ericvenzon9626

4 ай бұрын

Why is it that that when I tapped the red wire in a fuse and black wire on a ground, the led lights up already without turning on the engine yet ?

its the 2.0 ?

What are the yellow wires for I got the 2.0 kit

@arpvisuals

Жыл бұрын

Man, I searched all over for that answer. When I first got the lights. They enable LED lights to have dual functions. So one person told me that if you want the lights to work with your blinkers, the yellow is to be attached to your fuses that control your blinkers. My car has fuse boxes all over the place, and I could not find the blinker fuses yet (haven't looked that hard). I may have to extend those wires and run them to the blinkers if I want to use that effect. I hope this helps. Let me know how it goes for you.

@ridin98civic

10 ай бұрын

Not everything needs to run to a fuse... and I don't see a single relay in use in all of this wiring... which is incorrect

I have the same car what is the measurement of the strip you used?

@arpvisuals

Жыл бұрын

I didn't measure. It came pre-cut Abba I used the entire strip. They don't recommend cutting the strip.

What are the yellow wires for?

@arpvisuals

Жыл бұрын

I searched all over for that answer. When I first got the lights. They enable LED lights to have dual functions. So one person told me that if you want the lights to work with your blinkers, the yellow is to be attached to your fuses that control your blinkers. My car has fuse boxes all over the place, and I could not find the blinker fuses yet (haven't looked that hard). I may have to extend those wires and run them to the blinkers if I want to use that effect. I hope this helps. Let me know how it goes for you. Reply

It won’t stick because it’s to cold out you should have used a hair dryer to heat gun to warm the glue and the car slightly and very carefully! Please clean that engine bay this spring too. GENNY is crying out for it.

@arpvisuals

Жыл бұрын

Thanks! I did not even think of that. Much appreciated

Where u get that from

@krobturn5864

2 күн бұрын

I want to order for my genesis G80 3.8

I disliked your video because I don’t care how the lights look in the daytime. How could you not have a nighttime viewing?

@arpvisuals

Жыл бұрын

It was an installation video. Not a video about how it looks at night

@watUlookinat500

Жыл бұрын

Couple of things 1. It's daylight and he's in the shade, his camera was affecting how the lights brightness looks. 2. If you're complaining about the dot look, cameras tend to show that or the leds blinking due to the way they work.