How to Install Exhaust fan in double glass window replace to plexiglass 🛠🛠
Ғылым және технология
How to Install Exhaust fan in double glass window replace to plexiglass
Acrylic Glass / plexiglass
My son see the Exhaust fan book and say it you make not good 🛠
Пікірлер: 25
Impressive work.. You have some talent
Good bezig man ;)
you did good
goed bezig man ;)
what kind of worker should i hire to install a vented hood? i need the hood to be vented through a double glazed window in kitchen. so i think I'll need some kind of glass worker. but i don't know what qualification worker i should look for?
@alt4u
12 күн бұрын
you need plexiglass Acrylic Glass / plexiglass
nice
awesome!!!
What was the black tape like that you put around the circle cut, then you drilled screw holes in glass?
@alt4u
2 жыл бұрын
that is Cellular rubber band 3mm to not make noise & triling
What is the IP rating of the fan ? Any risk of short circuit if there is heavy rain outside splashing on the fan spigot ?
@alt4u
Жыл бұрын
outside is balcony from outside not rain to ventilation
@alt4u
Жыл бұрын
How to cut Plexiglass New video kzread.info/dash/bejne/i5aE29OcgK6waKg.html
how did 1:48 goes to 1:49? did you cut a hole and with what?
@alt4u
Жыл бұрын
How to cut Plexiglass New video kzread.info/dash/bejne/i5aE29OcgK6waKg.html
So far, so good! I installed this fan yesterday. kzread.infoUgkx7yWIKcrbA9KMHkGSfcgxW2lsjHT6B8Sh I've been watching a continuous radon monitor in my house for about a week, and the levels have been running between 4.5 and 7.9 pCi/L. Shortly after I installed this fan, the radon level started dropping, and in less than 24 hours since I installed it, the level is now 1.9. My basement is approximately 2,000 square feet. Total home square footage above basement is approximately 4,000 square feet. The noise level so far is very quiet. Mine is installed indoors, so I had to purchase a cord and connector. If I have any problems later, I'll update my review. But for now, I'm very pleased with it.Update after 48 hours: Using a constant monitor, my radon is now fluctuating between 0.38 and 0.45 pCi/L. I've moved the monitor to my basement and am getting a constant 0.43 reading. After 24 hours, and when I know the weather will be safe, I'll place the monitor outside for about 12 hours. I'm thinking that the 0.38 to 0.45 may be the outside "ambient" radon level. I'm using this monitor (purchased from Amazon): Corentium Home Radon Detector by Airthings 223
Dats other koek!
how you cut plexiglass
@danlucas148
2 жыл бұрын
Looks like he probably used a jigsaw, doesn't have to be a perfect circle as the trim from the fan will cover and rough edges. You can draw a line round the fan with a marker to give you the line to follow.
@alt4u
Жыл бұрын
Use a saber saw or jigsaw with a fine-toothed blade for larger circles. Mark or scribe the circle and drill a 1/4-inch pilot hole slightly inside the perimeter. Put the blade through the hole to start the cut, then saw around the circumference.
@alt4u
Жыл бұрын
How to cut Plexiglass New video kzread.info/dash/bejne/i5aE29OcgK6waKg.html
u didn't show how you cut the glass pointless
@alt4u
Жыл бұрын
Use a saber saw or jigsaw with a fine-toothed blade for larger circles. Mark or scribe the circle and drill a 1/4-inch pilot hole slightly inside the perimeter. Put the blade through the hole to start the cut, then saw around the circumference.
@alt4u
Жыл бұрын
How to cut Plexiglass New video kzread.info/dash/bejne/i5aE29OcgK6waKg.html
Wall fan in a window.. shameful