How To Install Catch Cans On A First Gen Nissan Titan
Hello again friends, today we are installing catch cans on my first gen Nissan Titan. I recently rebuilt this engine and spent so much time and effort cleaning it I would like to keep it that way. Below you will find the kit that I bought along with the fuel line I ended up using. I bought two so I can have one can for each side.
Catch Cans: amzn.to/3OQZvp0
Fuel lines: amzn.to/3bAeXal
Check out the Official RTCG website! rtcg.tv
Support the channel and get a cool t-shirt: represent.com/...
**This video is being performed by an experienced individual. Any attempt to repair automotive parts or its systems carries risk of personal injury. Always follow safe practices when working on vehicles such as using safety glasses, jack stands, not wearing loose clothing, etc. No guarantee or warranty is implied by these videos. Use the information in this video at your own risk. If you don't think you can perform the job, then do not attempt it.
***Any purchases you make using the links provided help to support the channel at no extra cost to you! As an Amazon Associate, I earn from qualifying purchases.
#howto #diy #auto
Пікірлер: 23
I have a 2015 infiniti qx80 with 210000 miles , very similar engine , i recently did the valve covers and cleaned the valves (PITA) this video is helpful to know where to place my catch tanks . Btw , at 210k miles the engine looks like new still !!
Those flimsy hoses were collapsing from vacuum during my initial install and tests. I got fuel line and no issues. The wire stuff works great for me. On my frontier, I usually drain about 30 to 40 ml of oil per oil change.
@Rythecarguy
2 жыл бұрын
Same, I ended buying more fuel line like I used on the left side and it's perfect. Used fuel line ok my X too. It's nice that you don't have to empty between oil changes and it just becomes part of the maintenance.
I’m fixing to do this. Instead of buying 2 cans, I’m going to get some brass Tee fittings. Love the channel and the work you put into it. Keep up the hard work!
Nice install. Be interesting to get a short/ mid/ long term review.
@Rythecarguy
2 жыл бұрын
I should be able to swing that. I installed them and immediately got in the car for a road trip so will be putting over 2k miles on them this week. 🤘🏻🤘🏻
Excellent video as always, Ry!
@Rythecarguy
2 жыл бұрын
Thank you!
13:50 Would you happen to have a before-pic if the Titan valves before you had them cleaned/rebuilt? I'm curious how much gunk was built up in them.
What about the filter u took out ? Did u leave the cans empty?
@Rythecarguy
Жыл бұрын
I do leave them empty. They do just fine without them. 👍🏻
Have you ever noticed one side collecting more fluid compared to the other side?
@Rythecarguy
Жыл бұрын
Yes sir, I cannot recall which is which but one is used nearly all the time and the other is when the engine is under heavier load. So for this truck when I am not towing one side barely sees anything.
@rickreiff6750
Жыл бұрын
@@Rythecarguy I tend to see 3 to 4 times the amount collected in the drivers side can compared to the passenger side can when I empty them
@Rythecarguy
Жыл бұрын
@@rickreiff6750 Yep, that sounds about right. Based on that it sounds like you don’t put a lot of load on your engine.
@rickreiff6750
Жыл бұрын
@@Rythecarguy I have tried to "baby" it mostly, 2012 SV 4x4, I bought it new, 141,000 miles on it now, I haven't towed with it, but do haul some heavy loads in the bed from time to time.
Is it From catch can -OUT to connect to the air intake valve ,the air intake is on top and connect the other tube to the valve below and is going to the IN-catch can? Thank you
@Rythecarguy
Жыл бұрын
Yes OUT of the valve cover INTO the catch can. Then OUT of the catch can, INTO the air intake.
Would it be worth doing 2 catch cans on the VQ40 in the Xterra, etc.?
@Rythecarguy
Жыл бұрын
If you drive it hard or do a lot of towing than yes. Otherwise I would skip it,
Ry, how's your experience been with the catch cans since your post? Value added for a NA engine VQ and VK series?
@Rythecarguy
Жыл бұрын
They've been doing great. They collect a decent amount of oil between changes but never get too full
Lo monte en mi coche con las mangueras que traían empecé a escuchar un silbido agudo y alto y me salto fallo de motor , inspeccioné con la máquina obd 2 y me aparece fallo p0300 , crees que daño algo ? Desinstale las maneras y fui a comprar de buena calidad pero ya no me dio tiempo de montarlas en el cach oil . Volví a colocar la manguera como viene de serie en mi Nissan titán E comprado 8 bujías nuevas y las montare mañana . Crees que podría haber dañado algo más serio ? Volveré a intentarlo con las mangueras nuevas