Very helpful and informative! I plan on building 2 predators for the grandson's go-cart build, and this carb along with a stage 1 kit should do the trick! Thanks for sharing!

@GoPowerSports

2 жыл бұрын

Glad it was helpful!

thankyou for showing the clip you pushed in with the spring couldn’t find that info anywhere

I had the exact problem you described, thanks for the vid! It was the rod not properly seated in Carb! ❤

@GoPowerSports

Жыл бұрын

Been there, done that. Glad this helped.

Awsome video I just got fourth gps 22mm carb from u guys never disappointed shipping is usually the delay but its always 👍🏼 good 😃😉

I just installed a vm22 on my 212 !! 👍👍 I haven’t put any performance parts on my engine. However I’ve port/polish shaved head Recut valve s and of coarse reset valve clearance Just a header pipe homemade muffler She’ll fly around the neighborhood if you can keep the front wheel down! Lol I kept a 65 t on back and at about 5-6 grand I’m leaning over the handlebars lol ✌️

@GoPowerSports

Жыл бұрын

Sounds great!

Best video for VM22 adjustment! Thank you.

Had problems with the Mikuni that came with my rebuilt XR200R motor, wherever the screws where it ran above 2000rpm choke worked as throttle no revs barely on throttle, so found one same as yours here said for XR200, had marks where it was set (idle 1.25t) kicked over ran a beaut straight away, been buzzing around the village on it tonight, just has a bubble in the fuel line issue cause it's modified with a CL360 tank and the fuel line is hooped down up over and down to the carb, atm has a fat clear fuel hose on, just need to let the air fizzle out 😂 it's like a soda 😂 then it runs great.....hoorah ✌🏻

Good stuff. Learned some things.

@GoPowerSports

2 жыл бұрын

Glad to hear it!

Thank you for the information I just install a Mikuni 22 on my Coleman CT200u and having trouble with the idle.

This vid is so professional that it got two jobs. Thanks lol

@GoPowerSports

Ай бұрын

Glad you liked it!

Did a good job are chief explaining the details and you didn't talk too fast and I can understand you thank you keep up the good work see you guys in Texas I'm going to bust your asses in the circle track race Steve monopolis Maryland I'm going to let you guys have it LOL

Super helpful!

@GoPowerSports

Жыл бұрын

So glad!

When we buy these from you, you all set the fuel mixture screw already so we don’t have to change this right?

Nice overview! What length throttle cable do we need for a mega motor 212 kit?

Thank you!

@GoPowerSports

2 жыл бұрын

You're welcome! Thanks for checking us out.

i have dual carbs on a RMZ 500. i have been having intermittent loss of power. the motor stays running but it wont run full power. i already changed the coil pack and still had the same problem. ran fine for an hour then about 30 seconds of power loss before back to full power.

Excellent

So I have a SSR 125 pit bike that I have purchased a 26mm Mikuni carburetor for and it will not start what should be the first adjustment I do? It does have a spark and it does have compression it will start and run with the old carburetor .thank you

Got one of these few months back... Got it tuned after it was doing the run away bike thing.. i got one ride around my property, put it in the garage the next morning it didn't want to start i got it to run didn't get far til l was pushing it back to the garage. Never got it going again.. got a cheap Chinese 35$ one and it started right up..

Thank you for posting this. Big help! Where did you get the wheels for your bike. Very nice!! Is that a Motovox mbx10. If so, I have the same bike and been wanting bigger wheels and tires for it.

raceteam lol i love it

@GoPowerSports

Жыл бұрын

We love you too

@Spacecruizer203

Жыл бұрын

@@GoPowerSports i love how you guys kept and keep this dream alive man like that og dude said at the rascal raffle happy holidays my ducar is still running i still want the tilly stage one tho by this summer 1Oo%

@Spacecruizer203

Жыл бұрын

@@GoPowerSports thanks fams

should do a follow up vid with spark plug reading after tuning the carb if its rich or lean. how to compensate and adjust/tune again if what is the result.

@Bulletman426

Жыл бұрын

I agree!!

@kylesyx8432

Жыл бұрын

I know this was old news. But there’s a lot to say about learning the carb yourself. The vm is so simple. You basically have a high and a low Always point your bike towards a wall on the incase you screwed the throttle up. It comes set close enough for your bike to run. So set your idle screw first, I sit my bike on a cradle to free up my rear wheel. I gas the throttle- turn screw gas throttle turn screw and after 5 min of gassing the engine, your ready to ride 👍👍💕

Will this fit on a mega moto 80 stock engine? I have one at home and ive been wanting to mess around with the engine without swapping the engine.

I have alot of popping when I slow down in speed say 5mph does that mean it's too lean?

Awesome 👍

@GoPowerSports

2 жыл бұрын

Thanks 🤗

What do I do if new carb is leaking a ton of fuel from carb and from excess fuel tube ? Do I need to adjust my carb again maybe it’s o ring issue not lined up ? Or jet pin?

Nice love it I just need help with tune

@GoPowerSports

Жыл бұрын

Send a video of what it's doing now

I have a mukuni vm22 from a kawaski ke125 1978 2 stroke i cant find a new clone to buy cause mine fit in the bike on a rubbee boot no screws and is located by ur right foot brake pedal behind a side casing so i was gonna clean it all out and try to use same one but i need to know how to reset both screw to a point where engine start and the ajust it cause all the clones online has the bolt on side with the pipe and if i get one of thoese i cant put case over it anymore and would be exposed and in the way for brake pedal please help me thanks

Mine came with 10 additional jets. Do you have any info about changing them?

One quick question. When i hook up the vacuum line that goes to the back of the crankcase it runs like crap. This is on a Tao Tao 120. It does run better with the vac or vent line open to atmosphere. Thanks

my air screw fallen out. but still works ok. is it worth trying to find new screw if still works OK.

pls, help me! is it okay if my VM22 only gets settled in about 5 rounds? screw head (mixture air/fuel) sticks way out of its little house/hole

After installing a new carburetor I like to spray the contact points with break cleaner and listen for an rpm change. No change is good. Change is bad.

@jeroldlafferty54

Жыл бұрын

That brake cleaner is hard on plastic and paint. If you're checking for vacuum leaks you may want to use a silicone spray. Very good point checking for possible vacuum leaks.

should i use the larger jets you sent with the carb???

Thanks for the video. What should I do with the carburetor when it cuts out at full throttle?

@dixonkuntz6909

4 ай бұрын

It runs on main jet at WOT. Change main jet, probably larger. Look at spark plug to see if it's running lean or rich.

I recently bought this carb for my bike, ever since i installed it my bike has been blowing white smoke out of the exhaust. it idles and runs good but it is chugging out a lot of smoke and the smoke smells strongly of gasoline, my previous carb did not do that. does anyone know what the problems might be? could it be running too rich and if so what does that mean and how do i fix it?

I just installed my carb to my mini bike axis m200 from lowes. And now when I start it, it just rips and takes off. I need help! Could it be anything to do with the engine ? The throttle cable? The carb?

Thank you! I just bought one of these from you all and plan to buy more. Is there a cover for the air filter as we go off-road or something you recommend? Thanks again for everything, long time customer.

@GoPowerSports

2 жыл бұрын

You could use the air filter cover that come with the stage 1 kits, and just zip tie. Other than that, we may use a UNI Air Filter Pod for added protection. But we currently do not sell a smaller filter cover.

@Fatandslowbuthasthemostfun

2 жыл бұрын

I used to use a plastic coffee can on my daughters Atv when it was muddy. Drill a couple holes and zip tie it to the carb

Been fighting with my float bowls needle. Im still getting a bit more fuel because i still get a drop of fuel from that over flow line on the bottom of the bowl.

What’s different between this one and the 26mm?

I got a mikuni and the slide won’t go all the way to the bottom and the idle screw won’t work. We started it up and it ran at such a high idle and when we gave it gas it would stall out. Is there anything I’m doing wrong?

I have a chinese Mikuni clone that accepts mikuni main jets but keihin pwk pilot jets for some reason what number does mikuni pilot 15 and 17.5 translate to for keihin jets?

Any idea where to get this type pilot jet in europe? I can't seem to find these exact ones. What tags should I use to google search?

Where does the line that normally goes to tje air filter go? I replaced one in a Tao Tao 125 dirt bike and there is no spot on the new air filter.

Honda 389cc what carburetor can I use. I’m thinking in mikuni style. But I don’t know which one or what size. Can you help me with a suggestion

I have the makuni vm22 had it running a treat 1 minute then next start up. Idles really high and under throttle just bogs & stalls any help would be appreciated

Have alot problems with mine I bought mine from you guys with stage 2 racer kit would appreciate if one you guys could help my I've spent alot money with u guys over the years

I have the same exact carb on mine, but cant get it tuned at all, im up to a 150 main jet 5th slot on needle and still running lean, sprayed around engine n cant find any air leaks

Do you know where I can get a idle screw for that carburetor I lost mine?

I have two pit bikes with lifan 125cc engines and genuine Mikuni VM22's. What size pilot and main jets would you recommend at sea level?

@BubblezWay

Жыл бұрын

That what I’m trying to figure out as well I bought some jets for my genuine mikuni carb vm22 in it won’t fit

Hey. Can someone please give me a link to a twist throttle assembly that's good quality and fits this Carb? I'm having a realy hard time. Every cable so far has been too short by like a 1/4 inch. All adjustments are bottomed out.

Hey when you do all those mods do you thing the need to upgrade sparkplug ?????

How do I get the play out of my throttle cable, it’s a brand new cable and no matter how I adjust it it’s sticky and needs the throttle cranked up at back to start to open up

What size throttle cable are you using?

How do i make the end of my throttle cable longer? Yours is was longer than mine

Can I run my thumb throttle with this? carb set up Monster moto 212 conversion

Just bought one. The wholes on the adapter don’t seem to line up with the holes on my block. Any ideas of what I’m missing. Also mine didn’t come with a gasket

@Ghost88890REAL

2 жыл бұрын

It's pretty cheap on amazon for the gasket, For the holes it might be a little off but it should be correct. Unless you meant the mounting holes which idk the answer.

Is it safe to run a lacunia on a stock 212? Because I know there's no more governor once you switch to carburetors, so will the motor blow?

Let me know do you have to disconnect the governor to put that is covering Cajun land Church point Louisiana

Thanks for the information 👍

I watched your video, it's very good. One question there is a hose connection in front of the fuel inlet on the left side of the carb (choke side), what does that connect to? Is that another fuel over flow ? I know there is an over flow on the bottom of the float bowl. Not sure where the connection in front of the fuel inlet goes or connects to. PLEASE ADVISE THANK YOU

@peterhealey2668

3 ай бұрын

It may be a vacuum line, not used on bikes and atv's

I followed all your steps, got my bike running great, went to put my new air filter on and bike keeps dying. No dirt inside filter it’s bran new. Any idea why this keeps happening?

@johnwick-ii6il

2 жыл бұрын

If the motor die's as you are installing the aircleaner, you may have a bad seal on the main o=ring that seals the carb to the manifold. In many cases the seal will become off center when the carb is clocked level. If you cant remedy the failure issue, then take the carb and manifold off the motor...in one connected piece. Then look thru the manifold to see if the o-ring is showing anywhere. It should not be exposed in any areas. There isI also a small chance that a restrictive aircleaner will cause an already compromised o-ring to begin leaking. Good luck.

Sorry off topic but what size wheel hub are those wheels please?

How come you’re adjusting the air mixture screw with the air filter out? Is that recommended?

What wheel and tire package is on the mine bike? I want it for mine

Do you need gaskets in between the motor block and intake? and in between the manifold and carb???

@piotrplewa1889

Жыл бұрын

Yes

I recently bought a stage 2 kit with 22 lbs springs with the racer kit. I have everything installed but the problem I'm having is that it idles super high! Can you help please

@rcinful

2 жыл бұрын

I saw your comment this morning while trying to troubleshoot the exact same build as yours doing the exact same thing. After dinking all day with it I found that my dummy ass installed the manifold upside down so one of the little cutouts on the manifold was sucking air right in. Installed it correctly and walla! Idling correctly. Give it a look.

Hey is Autolite AR3910X High Performance Racing Non-Resistor Spark Plug a good spark plug for my 212cc engine because I want one that has a powerful spark

@GoPowerSports

2 жыл бұрын

It's a great spark plug. That or the NGKs are what we run. BP6ES.

How do I remove the stock long bolts from the manifold to install the new bolts to attach the carb?

@grumpycat3436

Жыл бұрын

Screw on 2 nuts up against each other and back the inner one out while holding the outer one still using 2 wrenches. It will eventually lock up and you can unscrew the bolt just by unscrewing the inner nut. To get the nuts off hold the inner one still and unscrew the outer nut.

found your video by accident I know nothing about the stuff. What kind of minibike is that and where can I get one? thank you

Just fitted one of these, not getting any fuel to the motor, bowl filling up, cleaned it with compressed air, what could it be.

Do these chikuni's run the same jets as the real Mikuni's? I've heard some people say they bought a jet kit and the threads & heads of the jets aren't the same as the original jets in their carb.

I have gas pouring out of the carb while it’s running… even after it’s off gas keeps coming out of the tubes. What can I do?

Is this the type of carb I could install on a gx240 honda?

i bought a new throttle cable but when it start it still goes a little nd i turned down the idle

What size main jet for stock 212 motor

Great video and info!! Do you Carry a carburetor that will fit a Yamaha PW 80? Thank you

@GoPowerSports

Жыл бұрын

No we dont

Nice video. Unless the VM22 clone is different than a true Mikuni... counterclockwise on the AF screw leans it out vs richens it up. Easy enough to listen for, but would be surprised if the low fuel circuit design was different... given it was basically stolen and copied.

what is the bronze-gold colored clip in the needle part called

What size studs do I need to buy for the new carb

Could you do a video or explain about all the different lines to do and where everything goes? What to do with the hole at the top of gas tank on predator 212cc engine, what to do with the valve cover hole, and any other thing? Would be much appreciated! Thank you!!

@GoPowerSports

Жыл бұрын

Great suggestion!

Gracias primaso

Does the governor have to be removed for the motor to run right? Because i just installed a mikuni (japan model, not Chinese) on my predator 212 but it dont run right. It surges real bad and even stays reved up really high to where the mini bike would take off if i didnt have it jacked off the ground...ive messed with the air screw, idle screw, as well as installing different size jets. But still cant get it right

@nickcarroll87

Жыл бұрын

Check your choke lever. The genuine Mikuni choke lever needs to be pulled up for it to be off.

Do you have the fuel lines diagram . ?

Will this work with the factory fuel tank no pump?

I’ve got a 212 and just put the carb on it. Definitely a top speed increase but when giving it full throttle off launch it bogs and feels like there’s a lack of power that wasn’t a problem with the stock carb. Checked the idle screw, air/fuel screw and needle as well as any vacuum leaks nothing. Does anyone have any suggestions

@stinkybritches4540

2 жыл бұрын

Maybe get a larger main jet.

@justconcentrate9843

Жыл бұрын

You need to adjust you needle

@daevincaldwell3201

Жыл бұрын

The jets sold with the carbs are meant for 110cc bikes. When it goes on a 212 it needs rejetted

@dixonkuntz6909

4 ай бұрын

​@justconcentrate9843 the needle is out of the main jet at WOT. The needle affects part throttle, from idle jet transition to main jet

@jarredhall9555

3 ай бұрын

115 jet

What throttle cable are you using

Love that Tire/Wheel set up. Are those 10"?

@GoPowerSports

Жыл бұрын

Ya, they 10s...we keep em clean though. :)

@jonbradshaw4517

Жыл бұрын

@@GoPowerSports yoooooo 😂 this is definitely a IYKYK comment! 😂 love it

Hey what type of fuel line do you use?

Where can i get those rims?

I have a Chinese dirt bike with a nobbi carb but it boggs at full throttle on erd and forth gear. How can i correct that?

Do I need to remove the governor on a Tecumseh in order to install this carb? Or just leave the governor alone as it is it not connected to the new carb?

@GoPowerSports

Жыл бұрын

We always recommend pulling the governor

My bike is bogging when I pull the throttle and I just bought the carb VM 22 mukuni on Amazon , it has new sparkplug new oil

What wheels and tires are on that bike?! It looks awesome.

Tried this myself on a new build. My drainage tube has gas coming from it while running. If anyone has advice or suggestions how to fix they're greatly appreciated

will this work on a boom vader 124cc

Tuned my bike when idle, sounds good. But when I start to go it sputters. Any ideas what this could be?

Is this specific model # carb compatible with the Predator 212? Also, does removing all of the linkage allow the engine to run ungoverned?

@GoPowerSports

2 жыл бұрын

This works perfect on the Predator 212. You would need to physically take out the governor from the engine and remove throttle linkages for this Mikuni to work.

@silverdropstang

2 жыл бұрын

@@GoPowerSports Thank you!

What if its acting like its in throttle when i start it up? If i had it on the ground it wiuld have took off from under me

jet size how to find the right jet size??