How to Install a PKE Passive Entry Push Button Start System
This is my video on installing a push button start pke passive entry system on my 2008 Mitsubishi lancer. I rate it on a difficulty level of 1 being easy, and 10 being hard, at a 6... If you like this video please comment, rate, and subscribe. Thanks!!
PKE Passive Entry Push Start: (Newer Version):
amzn.to/2vL77q1
Chip Immobilizer:
amzn.to/2VzMPdM
2008-2011 Mitsubishi Lancer Wiring Diagram:
www.modifiedlife.com/2008-mits...
Пікірлер: 351
You're the only one who's put up an install video who installed the button in the tumbler location. And the code tab on is a great extra. 👍
I also have a Mitsubishi Lancer Ex. I was looking forward to install this PKE system, but i was afraid i couldn't get any video in which my car has been used. But here we are the same car, now i can do it very easily. Thank you for the video, it is very helpful indeed.
We love this system. Really affordable. We installed it on our 95 F150 that we coyote swapped as well. Great stuff.
I kept wanting to cringe my face everytime you kept ripping off the parts from your car lol i do the same but i take it easy ur a savage on ripping stuff out lol great video!
@fashion7879
4 жыл бұрын
😂😂😂
Best install video on KZread for this by far
Hey, you said you were going to give a difficulty rating. From my perspective I give it a 10 for expert difficulty level. I would NEVER attempt to do this personally.
As a previous owner of one of these systems I found a few bits to be miss leading or missing. You didn’t explain how to hook up the door ajar/ open wires. Very important for programming. U can hook it up to ur dome lite. Then there is your key sense you disabled which can be hooked up to your ACC wire with a relay to reverse the polarity because some vehicles will not start without it. Also you didn’t state that there is a switch on the esaygaurd unit to go in between standerd or automatic transmissions mode. This disables the break wire for standards. And not everyone vehicles use the same door locks some are reverse polarity as well or double polled even but over all I have to Give you props for making the video just be more in formative about your information.
@Trouzt
4 жыл бұрын
Man I wish the manual said that the dip switch disables the break wires... It just says switch it for manual cars. Took me an hour to find a good break wire to tap into today.
Thank you for this great video, I have a 2008 Mitsubishi Outlander which is almost identical interior to the Lancer so this should help me a lot :)
Soldering wire is a big must especially ignition wires etc
That's a nice car and instrument panel.
When you bare the wires, You should slip the Heat Shrink over a Wire, You should then solder the 2 wires together, Then pull the Heat Shrink over the joint and heat to shrink, Just twisting the wires together is definitely bad practice as they can still pull apart, Heat Shrink is only to insulate the wires so they do not short, They are not intended to hold the wires together. Your other option is the Red and Blue Bullet connectors where you put a part on both wires to be connected. This can be a better way if you ever intend to remove the system when you change your car.
@joekirby4529
6 жыл бұрын
Agreed. Solder or crimp connectors, just twisting is asking for trouble as the car vibrates.
The last car stereo guy that did my system left a bird nest under my dash too! Needless to say I’m learning to do everything on my own now
Nicely made a video. You clearly know your way around a car, as well. I did question the lack of soldering, but you went on to explain the reason for that decision. I am wondering how you feel about disabling the steering column lock. It it a big deal to you? I'm undecided about doing this, myself. I own a 2006 Caddy CTS Sport Luxury edition and they have the same ignition switch issues and the Chevy Cobalt, as well as some other cars. The ignition key may turn off on its own while driving. As a result, the key must be kept separately from my other keys. Pain in the butt. Cadillac doesn't have a redesigned replacement ignition switch available to correct this issue. It seems that a remote start system would eliminate the problem completely. Thanks for the tutorial!
Hi, thanks for the video! Just wondering how did you do to be able to use the new key to open and close the doors? I mean, did you need to some kind of coding, or just when you connect all the wires it somehow link the locking system to they new PKE installation? Thanks!
For anybody wishing to do ANY wiring in your car: use crimps or solder your joints!
@wrecksandtech
6 жыл бұрын
Never trust crimp connectors. Always solder your wires. Unless you want to do the job twice.
@GabrielChartier
6 жыл бұрын
Heatshrink only isn't a solid connection?......;)
@wrecksandtech
6 жыл бұрын
Gabriel Chartier no its not, not by itself. When doing any sort of wiring on a car always use soldier. If you are using only heat shrink you are relying only on a twisted connection. There is not enough contacting surface to ensure proper connection. Soldier flows in between all the strands of the wire to ensure a complete connection.
@RUSTONE31
6 жыл бұрын
Solder definitely. I'm an installer and funny I seen other people use caps but for home installation lol
@dabiggcrunk
6 жыл бұрын
Or Wago connectors I like those for some reason.
I've got an outlander that had the smart key. It screws up a lot and the steering wheel locks and the fast key won't turn. It's the next best thing to push button start. You keep the fob, in my case, your purse, and you never have to see it unless you're changing purses. It unlocks the doors on second pull if the fob is near it and it starts if the fob is in the car. It has a switch though, as if it were a key. There isn't anything that goes into the ignition. There are buttons you can take the switch off. It's just a cap over it.
Hi, So this vid was posted a few years ago. How's the system working for you now? Any issues?
I like the 3 red switches on the left side of the dash. Must be a NOS switch, Vtec switch or something like in the Fast and Furious.
“That’s my stick shift”🤣
It's been a while since you installed this. Does it still work? How do you like it?
Double unboxing bonanza!
I would like to ask if I have an alarm with pke equal to the one of the video. The problem is if you are near and open, will you always have an installation problem or with the antennas?
Hello nice video, did you integrate trunk release function with this PKE?
ur the man. question my frend. i got a jetta 2012. im the second owner and i only have one key. i also want to install a start button. u think it will work with out having the original key with me all the time? I'm afrid to loose it.
/ Im working on an install right now, I can't get pass Note 8, how did you manage the GWR wiring?
Very nice detailed video. How did you bypass the transponder chip?
Awesome video! Does work on all vehicles? I have a toyota fortuner.
My girlfriend wants one for her 2012 Malibu but the Malibu has remote start from the keyfob. Would she still be able to use that?
Great tutorial. The real Accion starts at minute 10:18
Good video, thanks ! I just installed one of these on my car and there are a few things I can't get to work. The car will not remote start with the key fob (but it will turn the car off). I notice you have a manual transmission, so do I. Did you put dipswitch 5 in the "Auto" (down) position to get it to work ? Also did you hook up the dome light trigger wire and does your dome light come on when you unlock the car ?
@btgm407
4 жыл бұрын
Any luck getting remote start?I have the same issue
@NW_Mechanic
2 жыл бұрын
The dome light trigger wire will not turn on the dome light when you unlock the vehicle. The trigger wire is what triggers the alarm if the doors open and dome light comes on, light bulb turns on and completes the circuit triggers siren.
What’s the name of the easyguard wire you showed at 15:25? Seems to be connected to a wire under the stick shift which car wire did you connect to?
What did you do with the stock alarm system?
I already have a push start button and on Hyundai Elantra 2016 . I was wondering if it can be installed an auto start system ? I was told that is not possible . Please let me know. Thanks.
Nice video! I purchased the same unit from eBay, my for my 2004 Ford Explorer my fobs have the lock/unlock/trunk release and panic though. Hopefully it'll be the same install. It should be here in a few days. You should show another video with you walking up to the car and it unlocks and when you walk away it locks.
@TheAutoDIYGuy
7 жыл бұрын
Bryant Kelley awesome... I got the same kit as well 😅 i didn't this kit was so popular... I installed it in my 2005 Lancer. Works great. You can check out my tutorial too if you like... I may have some additional points that might help you out.
@thedjrgroupllc
7 жыл бұрын
Bryant Kelley I need one with a trunk release for my 2001 Lincoln LS. Can you post the link for the one you purchased just in case the one I'm looking at doesn't have that capability?
@bezi99
7 жыл бұрын
dJr Partners, ltd they actually ended up not have my anymore in stock after I purchased it and they ended up sending me this one instead. I bought it from eBay www.ebay.com/itm/152408346403
@bezi99
7 жыл бұрын
Actually I just checked, and this one is out of stock as well. Just jump on eBay and search push button start alarms and take a look at what the hey have.
@TheAutoDIYGuy
7 жыл бұрын
dJr Partners, ltd the one I used has the trunk release function as well 🙂
Did you install the immobilizer? What do you search to find out which wires are which?
Hows that button holding up? Would you recommend buying it ?
Nice Video
can you show how to use keypad ? what happens if your car is running and you get out. does it turn off the engine and locks the car ?
3 years later, how is it holding up for you bro
@jasonjr2500
3 жыл бұрын
@Shepherd Denver how has it been?
Love ur car
What did you do with the orange foot brake switch for it being a manual?
I want to install it on 2007 FJ Cruiser do you recommend it?
Hey buddy...I have a manual van yet the engine cranks but wont crank over when i put my foot on the brake. To what did you connect the Engine Start Stop button and did you step on the clutch alone? Thanks....
Nice Video! Can I put that same system on a 98 Rangerover?
I assume you have bypassed your immobiliser or have you attached a chip to your antenna ring?
Did you install the signal lights as well? Mine needs to be connected, do you know the wire location and colors?
Hi bro door trigger lock and unlock wire (-) must use diode?
Could this be installed on any car? I have an 89 Mercury Grand Marquis I'd like to do some "updating" to.
Two questions 1) can this system works on a lancer 2000 model? 2) can the multifunction steering wheel work on the lancer 2000?
Is it possible that we start the car engin with pouch button switch from out side the car. jaust like the security door key??plz
#1k like right here 👍
hi...I've set up a start stop for the lancer X. no problem. but what do I need to do to use the original key and fabricated alarm..
Hey nice video and thanks but i have a question?. I got a 2004 Toyota celica and i have to switch out my 4 prong relay for a 5 prong relay but the diagram is confusing so can u make a video installation a push start installation with a 5 prong relay or do u have a email i can email u the diagram and u can try to explaining wtf its talking bout
How long does the battery last on your keyfob sir?
Till someone steals his car with an orange
@gabumoh
5 жыл бұрын
That would be fun to watch 😂
@demetrisa.8571
5 жыл бұрын
Hahahahaha
@mx8manger
4 жыл бұрын
Orange pi board you mean ?
@real_ultrajoe
4 жыл бұрын
Seem really fun and impossible
@lumi2798
3 жыл бұрын
As if a screwdriver wouldn't simply do the job 😌
Can you further explain the part about the fuses and open and closed circuits? Did you have to get those fuses separate? Lastly, for the "remove key" sign, did you just cut those three wires and it went away for good?
@HumbleStartBigFinish
7 жыл бұрын
Thanks so much in advance!
hello. i have one simular installed. do you know why the light flashes 5 times after unlocking?
Only question I have is, does the start switch stay on? I'm looking for an upgrade for my vehicle and I want it to look completely stock, like a Corvette their switch only comes on when you touch it.. just wondering. Great video. BTW I like the blue accent pieces brighten up the interior.👍
@xiaocardot1160
3 жыл бұрын
Friend, it seem you are looking for a product like the video show,it is happen to we have the similar product,our produst suit for above 90% car.we have 4G gsm gps car alarm,smart watch car key car alarm ,liquid crystal key,watch key smart car alarm,remote start module...so on. maybe you will interesting in them.you can look at my youtube know more and add me whatsapp know more:whatsapp: +86 13417625973 liquid smart key control car:www.ebay.com/itm/284267230545
Hi, in our car to shut down all electronic part like a stereo it's necessary remove the key, how can shut down if the key it's inside of the ignition switch? Thanks
Do you have the link to buy one of those thanks
I have the exactly system and car. I connected as you said . but somehow the unlock is not working but the lock is working properly . do you have any idea what I did wrong. I can tell you and show more in detail if you willing to help me out . Thank you so much.
I know this video is like 3 years old but I have a question I have a 2005 lr3 and I lost the key can I convert to push to start thank you I appreciate it
Car Insurance Cover-up matters across Europe so looking for ways to be aligned with after installation. The issue with locking steering wheel after turning off the key and leaving the car I figured out. Besides that who literally owns the key may also start the engine, one less problem I guess. From that point of view would everything be fine to me. But locking steering wheel concerns, though. These are my thoughts on that issue.
do you still have your steering wheel lock and shift lock
How did you bypass the immobiliser?
does you ride use the canbus system?
How have u l done that horn signal when close the doors?
It's been over 2 years since u installed this ... how is it working now
i don't understand something not with my installation manuel. There are 6 whires brown for ON CUT,yellow for start two red whires for +, white for ACC and orange for on. There is also a yellow whire that must go to a relais. from the relais goos 3 cables. 1 to the start motor 1 to the start switch and 1 to ACC ON. Where has the ON CUT go to and where has te cables from the relais has to go to?
Horeeeeeee sheeeeet, You are a salvage animal my man. Lol
Great video. Just have a quick question? I have a 8th Gen Honda Accord V6 Coupe 6Speed manual. Do you think this would work on my car??
@quentinc1275
5 жыл бұрын
Yes but dont do it there's a good chance it will fail in time. Also if you are looking to sell the car down the road more people are likely to offer less or turn away because the car is more vulnerable of being stolen
@V-TecHondaLove
5 жыл бұрын
@@quentinc1275 Oh really man, Wow! I just got mines and was going to install it when the weather warms up. So what was your bad experience with the item? I'm asking because 98% of the videos I've seen with it installed the guy's are all happy.
Does the *Touch Keypad* work okay?
i installed mine but do you know why my beeps twice when it arms
Nice
What happens if you try to lock the car within 15 ft does it just unlock because your still within proximity
The title should be called “ how to install a rats nest into your vehicle lol”
Can you put this on a later model vehicle
That much work I think I’ll just turn the key
@DoseOfR24
5 жыл бұрын
max F but do you realize that Push start remotes can break and cost more money then just getting a spare?
@Madvillian
5 жыл бұрын
@max F How the hell are you locking your keys in the car when you lock the car with your keys?
@johnathanirby3274
5 жыл бұрын
I'll keep my normal key... too much hassle for the vehicles age (I have an 02 Expedition) the most I need is automatic start...
@Chevyshow
Жыл бұрын
Thanks to this video I now charge $400 for install 😎
Is there one for a Mini Cooper s 2003 R53?
Can i do this with honda insight?
Ugh. I'm having flashbacks installing keyless entry in my car. Debating putting a passive system in now but ugh. That moment when you pull out the second harness and you got the phone out and the paper. That was my life for 2 days of hell. Lol. Luckily it all worked in the end but half my connections were behind the kick panel fuse box so I spent most of it upside down to be and to actually do anything.... I think I'm good with keyless remote as is lol.
Will it work for a 2004 hyundai sonata ?
Do it work on all vehicles
Will this work on my 2019 Elantra??
Can i put this in my key in on a 2001 chevy tahoe
Probably AAM (body module) of mine is malfunctioning and I need to get a new remoter. The issue with programming and resyc it turns out. No tool at all to do that, therefore this would be considered as an option for me to have my remoter fixed, seemingly no other option left.
Will your insurance go up as they could see this as your car being less secure
What's the name of app to tell you diagram wire on mobile? Please tell me
Is there a smart entry feature just like you said earlier in the video? That when you walk near the car it will automatically unlock the doors without pressing the unlock button on the key fob?
@EFFEKTRecords
4 жыл бұрын
Yes
@zachlaraquel796
4 жыл бұрын
@@EFFEKTRecords how is it holding up after 2 years? Any issues or anything because i'm planning to buy that exact pke system for my car
Do we need to press the start button just one time for cranking or we have to hold it until it starts?
@btgm407
4 жыл бұрын
Hold for 2 seconds.
welldone
hy there,i have only one question...when u get in the car and steering wheel is locked, how do u start car(or how do u unlock the wheel) ?
@EFFEKTRecords
7 жыл бұрын
+Mario Kordić the spare key that I cut and stuck in the lock cylinder is for the steering wheel lock, then to start u push the button
amazing. i want to install it in my VW Passat B5 1.6 from 1999. But i don't know which wires i should use :(
@xiaocardot1160
3 жыл бұрын
Friend, it seem you are looking for a product like the video show,it is happen to we have the similar product,suit for your VW Passat. maybe you will interesting in them.you can look at my youtobe know more or add me whatsapp/wechat knoe more:+86 13417625973 liquid smart key control car:www.ebay.com/itm/284267230545
Do you still have the link to the wiring diagram? I don't see it in the description
@EFFEKTRecords
7 жыл бұрын
sorry about that, I'm putting it in the description now... but here you go: www.modifiedlife.com/2008-mitsubishi-lancer-car-alarm-installation-guide/
Any idea if this would work with a 1991 190e?
How can close the car with the key in the ignition switch?
WHEN TWISTED THE WIRES TOGETHER I WAS DONE !!
Where i need conect black wire ( oil box input) ?
Goood video
Also looking for ways how to install that system properly on my car without having some issues with the immobilizer with RF 315 I guess.