One more tip for those who bother to scroll down and give the video a like or write a comment ... I really appreciate it ... So the tip is, afterwards don't forget to hang your " Sound Deadening Pad " back once you are done. If you don't want the " WOoooong " when you close the door , you're welcome 🫡 😄 👍
@de_Leuran Жыл бұрын
insanely satisfying work! Love to see an old BMW restored the right way. There must be a big future for this channel!
@Restorezone
Жыл бұрын
Thanks ! 🙂
@EstebanValentin Жыл бұрын
Good stuff as always buddy. The attention to detail is great, I bet this will help many DIYers.
@kennydelobel Жыл бұрын
Great quality vid as always, explained so even dummies like me can understand 😅
@Restorezone
Жыл бұрын
Thanks! 😁
@TheStreetBastard Жыл бұрын
Youre structured and clean way of work is amazing and super interesting!
@danarbuckle6640 Жыл бұрын
Very very nice work. I wish you would have shown if you adjusted the door gaps after you put the doors on.
@Restorezone
Жыл бұрын
I find the easiest way is to screw the bolt in from the inside, and just tighten it until it just touches the door. And then tighten very lightly, so that you can move the door up and down with minimum force. Then close the door carefully" be careful not to hit the fender" once the door is closed and then look at the seams, open the door halfway and slide it up and down to the position you want and check again, a video about this will seem a bit boring, this is fitting work, and it is a lot of opening and closing until you get the desired result. good luck and be patient :)
@danarbuckle6640
Жыл бұрын
@@Restorezone Thanks much for your reply. Keep up the good work. Subscribed.
@EricsUnfinishedProjects Жыл бұрын
Beautiful job and great instructions regarding the process. Thanks so much!
@jonathan8349 Жыл бұрын
Well done on the door and great job on the video!
@mrt7152 Жыл бұрын
Zoals altijd, mooi werk!
@conceptalfa7 ай бұрын
Great work, thanks for sharing!!!👍👍👍
@EvilSlayer6 Жыл бұрын
Very nice job! Love too see it! 😊
@MrMokkeli Жыл бұрын
Love ur videos, hope I will some day repair my own 2002
@Restorezone
Жыл бұрын
Thank you ! I hope the same for you 🙏🙌🙂 ...
@gwynn1104 Жыл бұрын
Great job, I have holes in my outside skins in both sides and wasn’t sure if this was a job I could do. I think it is though 🤘
@Restorezone
Жыл бұрын
thanks , and I say good luck , for when you start ;) will be fine
@philippehuget3435 Жыл бұрын
C'est vraiment du super boulot !
@Restorezone
Жыл бұрын
Merci! 🙂
@carsandwhisky2002 Жыл бұрын
Nice work!!! I’ll be DIY restoring several of my 02s soon @carsandwhisky
Пікірлер: 22
One more tip for those who bother to scroll down and give the video a like or write a comment ... I really appreciate it ... So the tip is, afterwards don't forget to hang your " Sound Deadening Pad " back once you are done. If you don't want the " WOoooong " when you close the door , you're welcome 🫡 😄 👍
insanely satisfying work! Love to see an old BMW restored the right way. There must be a big future for this channel!
@Restorezone
Жыл бұрын
Thanks ! 🙂
Good stuff as always buddy. The attention to detail is great, I bet this will help many DIYers.
Great quality vid as always, explained so even dummies like me can understand 😅
@Restorezone
Жыл бұрын
Thanks! 😁
Youre structured and clean way of work is amazing and super interesting!
Very very nice work. I wish you would have shown if you adjusted the door gaps after you put the doors on.
@Restorezone
Жыл бұрын
I find the easiest way is to screw the bolt in from the inside, and just tighten it until it just touches the door. And then tighten very lightly, so that you can move the door up and down with minimum force. Then close the door carefully" be careful not to hit the fender" once the door is closed and then look at the seams, open the door halfway and slide it up and down to the position you want and check again, a video about this will seem a bit boring, this is fitting work, and it is a lot of opening and closing until you get the desired result. good luck and be patient :)
@danarbuckle6640
Жыл бұрын
@@Restorezone Thanks much for your reply. Keep up the good work. Subscribed.
Beautiful job and great instructions regarding the process. Thanks so much!
Well done on the door and great job on the video!
Zoals altijd, mooi werk!
Great work, thanks for sharing!!!👍👍👍
Very nice job! Love too see it! 😊
Love ur videos, hope I will some day repair my own 2002
@Restorezone
Жыл бұрын
Thank you ! I hope the same for you 🙏🙌🙂 ...
Great job, I have holes in my outside skins in both sides and wasn’t sure if this was a job I could do. I think it is though 🤘
@Restorezone
Жыл бұрын
thanks , and I say good luck , for when you start ;) will be fine
C'est vraiment du super boulot !
@Restorezone
Жыл бұрын
Merci! 🙂
Nice work!!! I’ll be DIY restoring several of my 02s soon @carsandwhisky