Excellent- easy instructions and the reasoning behind slack cable and how to fix it. A good video is the camera and pretend that everyone is new to it. Never mind people rushing a step, thinking everyone knows. This was a good tutorial.

Thank you Bike Teacher - This video helped me get a TranzX post working again on a Kona Process 134DL.

@BikeTeacher

3 ай бұрын

Awesome. Glad it helped. ⚙️

Best dropper install video on KZread!

@BikeTeacher

3 жыл бұрын

Thanks so much!

Great video! I just bought a new dropper and having never installed one and unable to find much on the model I bought, I'm happy to have found this video. Thanks! Update: I installed my KS LEV SI dropper using your instructions. The only problem I had was with the measuring for the barrel. KS included a piece to measure the distance between the barrel and the housing, but there were no instructions, and I had it upside down which caused looseness in the cable. Once I figured out my error I was good to go. Thanks again!

@BikeTeacher

5 жыл бұрын

Awesome, good to hear.

can't thank you enough good sir! was lost as to how to get the cable attached to the actuator on the post. this video saved me! much respect. fantastic video in the knick of time. thanks very much

@BikeTeacher

6 жыл бұрын

Your welcome and thank you!

Thanks for the video instructions. Very clear and complete. I wish I had found this video in my earlier search as it could have saved me all the trouble I'm currently experiencing installing a seat post dropper.

@BikeTeacher

2 жыл бұрын

Your welcome and thanks for watching!

I hope this is helpful, let me know if you have any questions.

@BikeTeacher

6 жыл бұрын

Did you get to see the video I have on that? Let me go back and take a look.

@BikeTeacher

6 жыл бұрын

Glad you got it. I for got my bike came with housing pre-installed. I have been experimenting with with cables to help find the routing. I clipped the end of the derailleur cable head and run it through using a magenta or pick to help it through. Then slide the housing over it.

@MikeAndrzejewski

5 жыл бұрын

The measurements you gave were super helpfull! I had a few issues trying to get the cable sized!

@MikeAndrzejewski

5 жыл бұрын

As a side note, you only need the second hex wrench to make it really tight..

@daibennett9224

4 жыл бұрын

Bike Teacher thanks bike teacher

Awesome video, thank you. It was great to see how the cable connects to the bottom of the post.

@BikeTeacher

4 жыл бұрын

Thanks Justin!

This was an excellent video and probably the first to be thorough and explain everything as if you didn't know what you are doing. I already installed mine but had some complications but with this video I was able to fine tune it to how I wanted it. Thank you so much for the help!

@BikeTeacher

3 жыл бұрын

That’s great! Thanks for the comment. Happy help.

@BikeTeacher

3 жыл бұрын

That’s great! Thanks for the comment. Happy help.

I followed along and did mine just like he showed. Works great! Thank you!

@BikeTeacher

2 жыл бұрын

Thanks Dean!!

I just installed my X fusion dropper and this helped quite a bit, thank you!

@BikeTeacher

4 жыл бұрын

Awesome. Glad to help.

@BikeTeacher

4 жыл бұрын

Awesome. Glad to help.

That was incredibly helpful, thank you. Nicely produced, too.

@BikeTeacher

4 жыл бұрын

Thank you Rick. I appreciate that.

As a first timer with this your video helped me tremendously. Thank you.

@BikeTeacher

4 жыл бұрын

Glad to help Brian!

Great video, really helped me fit my command post. 👍

@BikeTeacher

5 жыл бұрын

Awesome, glad to help.

Thanks a lot. This helped me repairing my bike during Corona Crisis while all bike repair shops are closed. 👍

@BikeTeacher

4 жыл бұрын

Glad I could help Hans. Stay safe.

Thank you for the video. I like how it's real world - you encounter a problem, like all of us, and trouble shoot it - like with the electrical tape. BTW, a cheap pair of hemostats or a needle driver would probably make your life a lot easier on the nut installation part.

@BikeTeacher

5 жыл бұрын

Thank you for the tips. I will keep that in mind when making videos, to allow for problems.

Thanks! Installing a new housing was the big issue for me, without specific tools. I hasld to improvise : I turned the bike upside down, fed the housing and the cable from the front hole to the bottom opening of the frame, there I attached the little metal cylinder that attaches to the seat post and I tied a shoelace to it. From there it was very easy to guide the unattached end of the sholace through the small hole and down the seat tube. Then just pull it and the housing follows the corect path. Then I followed this video. Hope this helps

@BikeTeacher

10 ай бұрын

Great!

many thanks, i'd not got much of a clue when my dropper failed. This helped, thanks.

@BikeTeacher

4 жыл бұрын

Your welcome!

Really good instructional video. Helped me a lot. Perfectly demonstrates why these days most droppers have the cable clamp at the lever end !

@BikeTeacher

5 ай бұрын

Thank you. I really love those levers.

Thanks dude. I found this video very helpful.

@BikeTeacher

5 жыл бұрын

Your are welcome.

This video was extremely helpful in installing my dropper post. Thanks for sharing!

@BikeTeacher

7 ай бұрын

Your welcome Jimmy. Thanks for the reply. ⚙️🏁

Thank you, still helpful and relevant after 3 1/2 years.

@BikeTeacher

2 жыл бұрын

Great to hear! Thanks!!

Great video, super helpful!

@BikeTeacher

6 жыл бұрын

Thanks Tomek

Perfect pace, xlnt video, well done!

@BikeTeacher

5 жыл бұрын

Thank you!

Great informative video. Thanks for making it, it was all I needed to replace my dropper post cable and housing👍🏼

@BikeTeacher

10 ай бұрын

No problem 👍

Great video! Thanks for the tips! I plan on installing a dropper post on my 2017 Giant Trance 4. I am sure the concept is very similar. Too bad it is almost Winter here so I will probably do it next Spring! lol.

@BikeTeacher

3 жыл бұрын

Sounds good. Glad you liked it.

Best video. Follow exactly. Still had to improvise a bit by removing my handlebar switch to be able to feed the housing a bit more more into the body when attaching the saddle post.

@BikeTeacher

Жыл бұрын

Thank you. Glad it helped. ⚙️🏁

What a wonderful DIY video. Thank you!

@BikeTeacher

3 жыл бұрын

Thanks Malith , I appreciate the comment.

Thanks for tips on #9 barrel is a pain I put chain lube in my sheathing 😉

We’ve captured the command post!!

This was very helpful thanks

Thanks a lot for this tutorial, very well explained 👍

@BikeTeacher

2 жыл бұрын

Glad it was helpful!

Great explanation!

Super helpful! Building my new Stumpy today! Thanks Dude!

@BikeTeacher

5 жыл бұрын

Your welcome!

@BikeTeacher

5 жыл бұрын

How did the build go!

@mrw1054

5 жыл бұрын

Came out great Sir!

@mrw1054

5 жыл бұрын

Testing her out this weekend! Mt Dora trails here in Fla.

So a bit of confusion. After I cut the excess cable housing after measuring the extra from my seat post the cable housing was now much further down into the frame. I did not have the extra cable housing that reaches outside the frame so I can put the ferrel cap on correctly. What did I miss? Did you allow much extra cable housing in the front of the bike at the beginning when you cut one inch above the seat post?

your video helped so much for replacing my Remote Level and cable

@BikeTeacher

2 жыл бұрын

Awesome. Thanks

Nice video. I want to replace a Xfusion Manic 150 mm dropper tube with a 125 mm unit in my Turbo Levo MTB. Can I use the same cable or do I need to have a longer one to reach the shorter 125 mm unit? Thanks, Tom

You have convinced me to just pay the bike shop to do this for me because I don’t even have the tools for this and I’d mess it up so bad

@BikeTeacher

3 жыл бұрын

Too bad you did not live closer, this could be a special project.

Still a great training aid!! Thanks for posting!!

@BikeTeacher

2 жыл бұрын

Your so welcome.

nice honest explanation 👍🏼

@BikeTeacher

11 ай бұрын

Thank you. ⚙️⚙️

@1201suddenturn

11 ай бұрын

I watch from Germany, want to install a Crank Brothers Highline 3 on my Specialized Levo HT, installation will be similar. Great thanks

watching this to prepare for when my dropper gets delivered next week. You know the install would be a ton easier if these companies just had a farrel (don't know if that's spelled right) on the lever end. Then you could just install the cable with housing, install the dropper post and push it down, then pull the cable/housing to whatever length you want it, cut the housing and install the cable into the lever.

My carbon Ibis frame has cable stops in the bolt on plastic inserts, Does this post only work with a continuous cable? Do I need to drill out my plastic stops?

Really useful video...I am going to fit mine tomorrow.... Just wondering if a bit of play in the cable maybe a good thing in case you catch the lever accidentally ( like you mentioned with your knuckles ?)....but really helpful and you seem to have covered all the things that may become a "challenge'!

@BikeTeacher

4 жыл бұрын

Thanks! A little play may or may not be a good thing. The lever could be touchy and not respond therefore not activating the post.

Great video! Helped a lot!!

@BikeTeacher

4 жыл бұрын

Thanks!!

Fantastic video. Thank you so much!

@BikeTeacher

3 жыл бұрын

Thanks, your welcome.

Thank you for this very clear video. I have a question though. The lever that you pull with the screwdriver, the one where you need to fit the barrel in, is completely stuck in my dropper post. That's why I snapped my cable.

@BikeTeacher

4 жыл бұрын

It's jammed? It may need a complete disassembly to see what went wrong. Something bent or jammed. It also may not be repairable. May need new internals.

Very helpful, thumbs up!

@BikeTeacher

4 жыл бұрын

Thank you Adam!

Very helpful, thank you!

@BikeTeacher

6 ай бұрын

Glad it was helpful!

awesome explanation! thank you

@BikeTeacher

2 жыл бұрын

Your welcome Libertwins.

I didn't catch it but did the internal cable already have a barrel attached at one end? Or, did you have to attach a barrel at the lever end as well?

Great video, dude!

@BikeTeacher

2 жыл бұрын

Hey, thanks!

Thanks very helpful

@BikeTeacher

4 жыл бұрын

Your welcome Cathie!

the Kona remote 160 came with this seat post, I think carbon fibre is better but this is kinda cool!!

@BikeTeacher

3 ай бұрын

Ya. I think so.

Hi, me i know what housing cable cutter did you used?? Brand and model??thanks..

Great video. Thank you very much.

@BikeTeacher

2 жыл бұрын

You are welcome!

how to do it if the whole cable is pushed into the tube inside how do I take it out and put the dropper post back? the barrel is already on it

Not sure if you're still checking comments. But any suggestions on where I can find a silver barrel like this? I've checked a few local bike shops and no one has one. Thanks in advance

@BikeTeacher

3 жыл бұрын

Not sure, I would check with bikes shops, they mY have extra laying Around. The manufacturer mY give you one.

Good demo

@BikeTeacher

4 жыл бұрын

Thank you.

What do you do if you have a 2x10 thus having a shifting lever already on the left taking up the levers space. Is there room for a remote? Or would I have to convert to a 1x. I ride a Trek Fuel ex 5. Thanks.

@BikeTeacher

5 жыл бұрын

Yes there is room for a remote. A particular grip allows you attach it to the end of the grip nearest your shifter. Like it’s integrated. It would take the place of the grip clamp.

@mtbmt6908

5 жыл бұрын

@@BikeTeacher Thanks!

Awesome video

@BikeTeacher

3 жыл бұрын

Thank you, glad you liked it.

great video, thanks!

@BikeTeacher

2 жыл бұрын

Glad you liked it!

That's helpful... I think I'll buy one with an external cable. :D

@BikeTeacher

6 жыл бұрын

Yes, less fuss with internal routing in some cases but sometimes the externalhousing may move around too much and or rub and get caught on parts of the frame. For the most part you can lightly zip tie it.

You can use a 3rd hand tool up against the ferrules to eliminate ALL the slack before setting the cable stop

well done - tbank youi!

@BikeTeacher

4 жыл бұрын

Cool, your welcome!

So I have one of these and need to travel by air. The case I have requires removal of the seat and post. Is this pretty easy to remove and reinstall ? I have a Diverge expert Evo gravel with a X-Fusion Manic Dropper, 50mm travel

@BikeTeacher

3 жыл бұрын

I do not know that one specifically but they all should disconnect at the seat post with a quick release style or maybe you can slide the housing in to the frame to remove the post just enough off the bike. Removing the lever from the bar nay help.

Where can I get that barrel that goes on the end that attaches to the post or do u know if theres a cable I can buy that has barrel on both ends of the cable?

@BikeTeacher

Жыл бұрын

Places like Jensen, have small dropper post hardware parts. Here is a link.www.jensonusa.com/KS-Cable-Clamp-Cable-Clamp-Lev-Lev-Dx-Lev-272?loc=usa&gclid=Cj0KCQjwlPWgBhDHARIsAH2xdNebofi4lYg04LwCivJkPQdyTBUdZRnq5DqLB-09-FKeAfv-Pv_7WvkaApj5EALw_wcB

I don’t understand how after cutting the housing an inch above the seat post how you easily get another 8” of housing past the seat collar again. I have to slide my lever over to get close to having that much slack. Also before cutting your housing that 7” you had that nut thing on the end of the cable, why?

Question on mine Specialized Command Post Internal routing : When I ride it sinks down after a few seconds , and I have to bring it up with the lever , and again after a few seconds, something gets loose or I don’t know what it is , the pressure is right , please help , thanks

@BikeTeacher

6 жыл бұрын

Possibly too much tension on the cable. Use the barrel adjuster to loosen the cable, screw the barrel clockwise to collapse the barrel adjuster. If you have no more room to turn it clockwise you will need to loosen the cable at the pinch bolt and reset the barrel adjuster to half way at least.

@BikeTeacher

6 жыл бұрын

You can do a test and release the cable (barrel) at the seat post. It should be a quick release, Test ride it and see if the seat drops by it’s self. If it still falls by it’s self you have an issue inside. I would talk to Specialized to see if it can be fixed by you are it may need to be sent in.

@PopovskiDarko

6 жыл бұрын

Thank you very much for the quick response , I will try to fix it this weekend and see if that worked, will let you know

@willesloco

6 жыл бұрын

How did you get on? I have the same issue with a new bike. The seat drops while I'm riding. I've checked the cable and it seems to be setup properly. Tension is good. I'm thinking this could be a fault with the seat. Have to wait till Monday to phone the supplier!

@willesloco

6 жыл бұрын

I fixed it! the mechanic that set the bike up cut the cable to less than 12mm at the seat post :( I managed to eak out an extra 2 mm to the bitter end. It's not perfect and I will have to replace the cable, but for now it works. Millimetre's make all the difference with this seat post setup for the cable tension. It clearly states 17 mm in the manual so I do not know why they cut it to 10 mm?! Thanks for the video Bike Teacher, it was very helpful indeed.

How would you do the cable if my internal downtube hole is on the same side as my lever has to go on.

@BikeTeacher

3 жыл бұрын

That’s okay. You can still run it on the same side. They do it for derailleurs as well. There should not be added friction.

Nice video. Thanks for posting. Unfortunately the Command Post is not very good. I’m taking mine off my 2017 Specialized Enduro. It rattles (from day 1), loses pressure, and does not operate smoothly despite being rebuilt by the Specialized dealer. I am replacing it with the same X-Fusion unit that came standard on my Specialized Epic, which works way better. It is nicely dampened so it rises at the perfect rate and is very well priced. Specialized obviously thought the Command Post wasn’t great when they switched to the X-Fusion.

@BikeTeacher

4 жыл бұрын

I can say the same thing now. Mine was loosing air too. I am happy with my LEV, very smooth and reliable. All the ones I run into are still running smooth.

How did you route the cable itself? I'm installing on a trek. Did you have to uninstall the bottom bracket or is this not a fully internal cable routing?

@BikeTeacher

4 жыл бұрын

It is fully internal. This carbon stump jumper has its own routing tunnels. I believe I had to guide it the rest of the way into the seat tube.

Great video! Stumpjumper 2019 Evo, and my drop post broke at the cable connection 😔😔

@BikeTeacher

2 жыл бұрын

Oh no!

Hey I have a dropper post but I've lost the silver barrel you mentioned, do you know where I can get a new one?

@BikeTeacher

6 жыл бұрын

I found some online, I typed “ks lev dropper post parts”. Also called cable clamp.

@BikeTeacher

6 жыл бұрын

Or call Specialized directly.

I can't get the tube through my specialised stunt jumper 2019 any help? And also should I put the pipe through the top or the bottom of the bike

@BikeTeacher

5 жыл бұрын

I would start from the top of the bike. I feel gravity helps when trying to guide the housing (pipe, tube) through the frame. Maybe start eh the process with a cable. get the cable installed first then you can slide the housing over it, then you can pull out the cable. Check out this video for more tips ,kzread.info/dash/bejne/oqmFrs9xmtq2dco.html

@ode8478

5 жыл бұрын

@@BikeTeacher thanks

Can you help me find a dropper post that would work on my 2021 trek marlin 7?

@BikeTeacher

3 жыл бұрын

What’s the diameter specs? Of the post?

Do those Dropper Posts ever hit you on the way back up if you aren't positioned properly ? Ouch ?

Hello can you help me, I have a 2015 Scott Genius 740, I want to put a dropper post, I have the mesurments is 36.1 but I'm not sure if the frame has space for the internal cable or I need to get a external cable dropper? I was looking at the Brand-X Ascend Dropper Seatpost. Thank You.

@stewiegriffin8105

5 жыл бұрын

Camilo Lopez Your bike seems to have all the shifter and brake cables externally routed. But give a check near the seat tube (near the bottom bracket) for any holes for a internal routing to the external cables. If you don’t find them I think you got to get the Brand-X ascend 2 externally routed dropper.

@BikeTeacher

5 жыл бұрын

Hi, sorry for the late response. I always look at the frame for holes for housing routing like you mentioned in your other comment. Some frames run tight inside especially those that force the housing around or under the bottom bracket. This does not allow for free space for the excess housing to go.

@camilolopez6095

5 жыл бұрын

Thanks

@camilolopez6095

5 жыл бұрын

thanks

Do you think ill be able to internally route my giant stance 2 2020

@BikeTeacher

4 жыл бұрын

Most likely. I use a cable inside a housing and install into frame as a unit. Slide one or the other as a needed to make turn at the gram bend.

Thanks for this. The cabling broke on my levo and I tried to do it myself and ended up with massive extra cable. This allowed me to get the correct size without guessing

@BikeTeacher

2 жыл бұрын

Great! Glad to help out.

Hi I just wanted to ask that when I installed my dropper, I only tightened one side of the barrel - meaning that I didn’t hold the 3mm side whilst doing it. Will the barrel come loose and is that something to worry about?

@BikeTeacher

3 жыл бұрын

Possibly, it may not have allows you to get proper torque. Even thought the amount of force it’s needs is not much. It’s a 50/50 chance. Thanks

@usmanmohammed4043

3 жыл бұрын

@@BikeTeacher I think I’m going to buy a set of Allen keys because it’s bugging me now

@BikeTeacher

3 жыл бұрын

Better to be safe. I do get lazy but it always comes back to bite me. Thanks

What happens when you want to make the seat taller? Do you have to redo everything?

@BikeTeacher

2 жыл бұрын

You should have enough housing, always try to leave enough when first measuring. Thanks

THANK YOU THANK YOU THANK YOU THANK YOU!!!!!!!

@BikeTeacher

3 жыл бұрын

You are WELCOME Clint!!

Are the cables universal for all bikes or do you need a specific one per bike model?

@BikeTeacher

4 жыл бұрын

All droppers use the standard derailleur cable. There is a longer cable reserved for tandem bikes.

Do all measurements work for all compatible dropper posts with bike??

@BikeTeacher

2 жыл бұрын

Yes it should be the same.

Where can I get that barrel nut. My command post is missing that.

@BikeTeacher

3 жыл бұрын

I’m not sure. You can try contacting the manufacturer directly. They may just send you one for free.

You think I will be able to do internal routing with my 2020 Rockhopper 27.5?

@BikeTeacher

4 жыл бұрын

As long as there is a opening connecting the down and seat tube you should be okay. I assume there is a routing hole near the headtube?

@jievyjumawan5163

4 жыл бұрын

Bike Teacher yeah I see it now. I still haven’t received my bike, I just ordered it.

I lost my silver barrel, any advice where can i get this thing?

@BikeTeacher

3 жыл бұрын

A bike shop may have one laying around or online stores. Look for barrel adjuster for brake or derailleur. Which ever you need.

I believe the dropper have a plastic end bottom cap that also serve as a guide to measure that location of the small metal cylinder on the wire cable.

@BikeTeacher

Жыл бұрын

Yes, some will include it for initial set up. I like the levers that allow you to pinch the cable at the lever and not the dropper.

My Command post does not come up when lever is pressed. I have to pull it up by hand. How do I correct this issue?.

@BikeTeacher

5 жыл бұрын

Which post do you have? The manufacture told me it is normal (KLEV) to manually pull it up if the bike has sat several hours, then its usually good to go.

An old spoke ground to a point also works well for a pick

@BikeTeacher

2 жыл бұрын

Yes, and inexpensive.

I had a Stumpjumper in the 80s ffs LOL Somewhat useful. My Cube is pre-housed. Cheers

The brake cable end barrel what he uses , what's the actual name of them I can't find them anywhere

@BikeTeacher

2 жыл бұрын

Ferrule cap, housing end cap

@CM-1723

2 жыл бұрын

@@BikeTeacher thanks mate , I found one yesterday . In the UK they seem to be called solderless barrels . The ones with the screw in to clamp on the cable that is . The way it's done now is you buy a regular MTB brake cable and put the barrel end in the dropper post thread it through , then at the thumb lever there's a screw where the cable gets clamped down onto the lever without the need for another barrel end .

Good instruction video but I can't help thinking that your brakes levers are on the wrong sides. Motorcycles have the front brake on the right hand and so does my Turbo Levo FSR as supplied.

@BikeTeacher

4 жыл бұрын

I found that it is common for bikes to have the front brake lever on the right side if they are electric or from the U.K. I don’t ride motorcycles so it would be a learning curve for me.

In hindsight he didn't need to give the cable that extra 2mm for the silver barrel if you have to eat up that much play adjusting the seating slack at the end anyway.

did I miss when you routed the housing?, that's what I wanted to see.

@BikeTeacher

4 жыл бұрын

Here is a video with some internal routing tips. kzread.info/dash/bejne/oqmFrs9xmtq2dco.html

I would not want that dropper post hurtling towards my gooch. That is some serious speed.

@BikeTeacher

3 жыл бұрын

I call it the widow maker.

Transmision or brake cable?

@BikeTeacher

5 жыл бұрын

Dropper cables are typically derailleur cables.

I’ve installed about 10 droppers and the ones with the cinch/barrel at the base are straight from hell. Anyone looking to buy a dropper should opt for one where the head of the cable resides in the bottom of the dropper. Much easier to install dropper and adjust cable length at the handlebars

What kind of dropper is this?

@BikeTeacher

2 жыл бұрын

I believe that was a command Post, 2nd gen from Specialized.

Why not eliminate the possibility of an error and do all the trimming at the level?