When searching for a good grease, I came across MOLYKOTE PG-75, which is designed in Germany to work amazing with nylon/metal gears. Not cheap but you can find it in 30ml jars which is enough for 2 bikes

@dannyshows

Жыл бұрын

Thank you, maybe others can look at this as an option!

@UrDadsFavouriteMaleEscort

6 ай бұрын

Heyo, what do you think about mission automotive waterproof dielectric grease? Im about to crack open my hub motor tomorrow, first time in a thousand miles, overnighting a jar off of amazon.

@pauly51

5 ай бұрын

I couldn’t find small portions of pg 75. Only large amounts. Do you have link?

Wrong grease for the job my friend. You have to use a full synthetic grease like super lube because the distillates in the normal petroleum based grease eat away and break down nylon, plastic and rubber. Its not immediate of course but it can cause advance wear and fatigue mainly on the planetary gears causing a problem down the line. Next time use super lube synthetic grease.

@dannyshows

8 ай бұрын

Next time I will probably use lithium grease, should be soon 👍

@Nalladolla32

8 ай бұрын

@@dannyshows lithium grease is also not compatible as it's petroleum based.

@Nalladolla32

8 ай бұрын

Get mobil grease 28 or super lube synthetic grease. Both are safe for use on plastic and nylon and can be found online.

@dannyshows

5 ай бұрын

Ps the mobile one grease used in the video was fully synthetic.

@cryptokids3760

4 ай бұрын

Mobil 28 ftw

thanks for the video i jsut grease mine as well, but we have different gears mine was metal and no big holes on surface like yours

Why don't you use gear oil (e.g. viscosity 140) instead of the grease? The grease will be off the teeth in a short time - and only on the sides of the gears (but it doesn't do any good there) ...

The Mobil 1 Synthetic Grease I would not use, it tends to liquify in warm weather and run out of wherever you put it. I think I would use a waterproof marine grease instead.

Question I want to swap my motor but thing is will 500watt motor fit into a 250watt hub

what about moly lube like for motorcycles, that stuff stays put.

Good vid man thxs!

@dannyshows

Жыл бұрын

Appreciate the feedback 🙏

Does it need to add cooling fluid?

i used mobil 28 grease, and i replaced the one way clutch and nylon gears.. now my bike is quiet like new. I also used a 4 inch gear puller to get the gears off.

@pauly51

5 ай бұрын

I’ve heard Mobil 28 won’t last 60miles, then noise will return. Let me know please.

@northyland1157

5 ай бұрын

@@pauly51 So far its still quiet.. I'm not sure on my mileage. As a car mechanic, I see no reason mobil 28 won't last. It sounds like the person who said this had a bad bearing, and the grease covered the noise up for a little while. That being said there is no official grease, like there would be in a car gear box. I have not put 1000's of miles on the new gears yet, se we will see.

@pauly51

5 ай бұрын

@@northyland1157 sounds good, thanks. I’m curious if I should use Mobil 28, Lucas red and tacky or molykote 44 on my e-bike planetary gears in hub. There was one comment in a forum that Mobil 28 wouldn’t last 60miles.

nylon on metal does not realy need grease , It looks nice though .. Anyway the grease is gone from any actual bearing surfaces within a few meters of use ... thats why vehicles use oil baths continuously flushing the wear surfaces. Grease points are for non fully rotating surfaces like stearing bushes.. they need a top up regular.

@dannyshows

Ай бұрын

Unfortunately, I think you are correct. I added another 2000 miles on it and it sounds a lot like prior to greasing it. Next time I grease the gears I'll try to get a better idea of when they return to their degreased state; it honesty may have been about 200 miles or so. A previous comment mentioned adding a grease zerk, however, that would likely cause wheel imbalance unless someone came up with a clever way of balancing such a part.

@ZapytajRedditPolska

28 күн бұрын

​@@dannyshowsyou should regrease after 1000kms max. The grease is not immortal. The motor needs regular intervals of regreasing. 1000kms tops.

You did not say in the video how to remove the screws from the motor if anyone reads this, you're gonna need an impact driver, unless your motor uses allen(i'm not sure if they're all the same but mine were very tight and had phillips screws that are easy to strip)

When you say “bump”, you talking fist bump or Cain dropping able strength?

@dannyshows

11 ай бұрын

I think each bike will be different. Once I moved the casing section that comes out to the bottom, as shown on the video, it came out easily. I could see some bikes requiring a sledge hammer though given all the potential build up and rust that could bind a casing shut. I'd say just be careful and build up to greater levels of force if required.

The mechanic in me, wants to install a grease zerk.

@haydenshores9943

3 ай бұрын

That would make it way easier

@AaronHendu

Ай бұрын

You gonna fill the whole housing with grease then or what? Lol

@AaronHendu

Ай бұрын

We need proper bearing seals and we could fill our hubs with ATF.

You must use silicone grease... food grade as for plumbing

Google says I should grease every ride, or every 6-8 hours. I've gone 800 miles already and haven't done it once. Am I crazy? Or are people crazy?

How many miles in did you feel it needed grease?

@dannyshows

Жыл бұрын

I would not go past a thousand miles. Per other comments it appears AR uses lithium grease, this is consistent with the qualities of the grease that comes with the bike. With that said the grease I applied seems to work well.

@ZapytajRedditPolska

28 күн бұрын

​@@dannyshows1000 kms Max and you should regrease!

next time use a clean low cost toothbrush

Lucas red and tacky?

@dannyshows

5 ай бұрын

I almost purchased the lucas red and tacky that via Amazon before purchasing the mobile at a local auto zone. I think either would work great.

@pauly51

5 ай бұрын

@@dannyshows thank you. New subscriber. I suspect my planetary gears are dry. Only 300 miles slight noise in hub and year warranty has gone by. Juiced rip racer.

@hiandhello4183

2 ай бұрын

do not use that one, its bad for the gears

Very informative and straightforward

Tha sound was a slipping/worn clutch

@dannyshows

11 ай бұрын

You may be right, but short of researching for hours, this comment is beyond my technical expertise.😂

Did AR recommend that grease?

@dannyshows

Жыл бұрын

No they did not! I probably should have checked with them prior to doing this. However, this grease is commonly used in gearing.

@ibrahimadiallo7444

Жыл бұрын

@@dannyshows i just asked, will let you know what they say

@ibrahimadiallo7444

Жыл бұрын

@@dannyshows White Lithium Grease is what they recommend

@dannyshows

Жыл бұрын

@@ibrahimadiallo7444 That's what it looks like it comes with originally. Appreciate the confirmation!

@mattearp602

Жыл бұрын

How many miles in did you feel the need to grease it?

I have 14k miles on mine, you think I may have waited too long 😉

@dannyshows

2 ай бұрын

I'm at 3,760 or something like that. 14k is gnarly. How long have you had the bike?

@papablueshirt

2 ай бұрын

@@dannyshows It took me a year to get to 14k, It would have been 15k but the Jumbo came out and I started riding it. Dual batteries are great. I did put dual batteries on my H8, but the battery is on the back. The Jumbo the battery is in the middle so it is balanced better. My plan is to get both bikes to 15k this year if my back holds out 😀

@dannyshows

2 ай бұрын

@@papablueshirt Thats amazing. If you have any recommendations on mods you have founds useful please do share. TY!

It is me or just it sound the same just different angle camera 🤣(Before - After)

@dannyshows

Ай бұрын

It was def diff sound. Next time I will do the same angle lol.

To much grease applied.

@luddite2k465

11 күн бұрын

And you really should't use a brake rotor as a handle....

HAAAAA!!! ... contaminated gloves touching/handling the brake rotor.

@dannyshows

10 ай бұрын

Very true watching it again I am noticing how much contamination I applied on the rotor 😳. In my defense, I changed my gloves several times during this video.

@michaelt5624

10 ай бұрын

you still have to clean the rotors properly, and do the pads as well if you attempt to use it without cleaning it.@@dannyshows

@ctbale1

9 ай бұрын

It's fine. It's a ebike....it's not the space shuttle...jesus

so why dont we drill a small hole about 3 inches out from the center, on the brakes disk side into the side of the hub. be carefull and use high speed and break thru real easy then put white lube in with syringe and stick a piece of whatever in the hole afterwards. thats what i am going to do a film it for youtube so you millennial can pass it on. this fall on youtube kids.