Your channel is underrated. Hope your subscriber numbers go up because your material and content is nothing short of exceptional. keep doing what you doing.

@greatlakeshuntingandtracki5450

Жыл бұрын

Agreed

I'd use hotmelt and cut the front to save vane glueing but great info man. I completely agree with bareshaft tuning. If you can shoot very consistently, a bullet hole bareshaft=broadhead flying true. Infact if I shoot my broadhead when its calm outside and it does not hit center on a good break, I immediate shoot paper with a bareshaft and see if my bow is out of tune. Almost always the paper tear reflects what a broadhead does down range. Because of that I always keep a bareahaft of all my setups as a test of my tune.

Really like this stuff! Thanks a ton Cal!!!

Your bare shafting tuning explanation, solved all my issues. Than on top of the broadhead tuning. thank you.

Dude you a good as teacher. Lol best channel for lessons by far. I always come to u in the end when watching others to learn but u simple worded and understandable

Awesome video thank you so much for all your content!!!!

This video is very well done , very good information ,and like all your video's they are all very helpful.

Thanks for a very informative and easily understandable lesson. I am going to my club today to try this.

Another great video, very well explained....

Thanks for this.

another gread vid! keep up the great work.

Great explanation. Sometimes it's tricky to figure out if the fix is rest, shims, or spine but I guess you learn over time. Bare shafts are great to practice with because it shows any hand torque.

Just like, " Back in the Day" when you had to make sure that when I glued my nocks first, to orientate the grain of the wood , perpendicular to the riser, to have consist spine from arrow to arrow, and since shooting with fingers puts a horizontal flex into the arrow. Release shooting puts a vertical flex into the arrow.

To clear up confusion that is all over EVERY archery KZreadrs page regarding paper tuning. make it simple: follow the point.

Great content bro like always. Thx 🏹

Tune a bow from the beginning to the end

@InsideOutPrecision

Ай бұрын

If I used alll these techniques it would be a two week video haha. But from box to bullet hole is pretty easy, I’ll do it.

Thanks man. Pretty sure I was one of the dudes that asked for this. Exactly what I ws hoping for.

Always glad of free info I need every excuse possible... lol Thank you for taking the time and sharing...

Great video

Make a suggestion, you should use also a chalk board so you can explain your point. Excellent video

Would love to see what you do for pre season maintenance to keep your bow in tip top shape before you hit the field. I feel like that’s a subject that gets put to the side with most channels but could be the difference between success and eating tag soup.

I agree, it is a process. I do recommend to most people that they should error on the side of stiff though. Also keep in mind, most arrow spines, as far as I know, are determined at 28".

Awesome info....dammit I just cut a dozen shafts 2 days ago

love your videos! I'm also a lefty. the question I have is when I bare shaft tune and get a perfect bullet hole with the bare shaft from 6 to16 feet (and I mean perfect bullet hole. tiny even tears around hole no tear in any direction). I was surprised at 60 yrds that my groups were hitting left (4 to 10 inches) . At 20 yds my groups were hitting center. So I proceeded to group walk back tune and adjusted the rest accordingly. I got the groups to center at 60 yrds and 20yrds, but as I presumed I no longer had that perfect bullet hole with the bare shaft at 6 to 16 feet. So did I take my bow out of tune after walk back tuning . I was always curious about this. same question for broadhead tuning. Would love to get your input on this. thanks Scott

Very helpful, thank you.

Thanks i am in the process now and i was doing it right thank got cause i cut all my arrow time to shoot and see what happens.

So if I have to move my rest out of center shot to get a bullet hole with one arrow (Gold Tip Pierce) and planes like you said where it hits left but tail is right on target but then I shoot VAP TKOs and money. Any suggestions?

AT WHAT YARDAGE ARE YOU BEGINNING THE COMPARISON BETWEEN BARE-SHAFT AND FLETCHED. AND THEN DO YOU MOVE BACK TO CONFIRM AS YOU WOULD IN A NOTMAL PAPER TUNE

Does this hold true for broadhead flight too? My broadheads hit to the right but the shaft crosses over to the left.. Left hand shooter.

what about for bare shaft, going to top hats, for the bare shaft adjustments, versus moving rest? thoughts on that

@reaganriddle

2 жыл бұрын

Personally would say go for it. String is inline with the center just the same as the rest is.

Do you add electrical tape to the back to compensate for fletching weight when you bare shaft? Correct me if I’m wrong but wouldn’t the lack of weight in the back of the arrow change the dynamic spine if that “fletching weight” is missing?

@InsideOutPrecision

2 жыл бұрын

I’ve never noticed it making a difference.

@donaldvonlintig8445

11 ай бұрын

Yes, Everything makes a difference, feathers only weigh, a couple of grains by any plastic fletching, weighs "a ton" Even Nocks, can change the tune , considerably. Take a Easton X nock, on a 5mm F.M.J, bare shaft, tuned. Then put on a Nockturnal lighted nock, and watch your tune go out the window ! Guaranteed the spine gets stiffer, because of the weight difference and it will be Nock Low, because the dimension of the thickness, of the nocks are not the same. Easton X nocks are .160 and Nockturnals are .190 thick. Being a "Precision Machinist" for 45 years, I measure Everything !😊

Just FYI, arrows can fly with the tail off center due to timing issues and, in my case, cam lean.

@InsideOutPrecision

Жыл бұрын

Yeah this video was made with the implication that cam timing is set and your bow is tuned through paper

@InsideOutPrecision

Жыл бұрын

Also, can lean is normal. Bows with split yokes are designed to lean the cam one way or the other so you can tune without moving your rest inside or outside of center shot

Axis arrows don’t have a spine because of how they manufactured though.

I’m shooting 300 spines. And my arrows go right down the middle at 70lbs draw weight. And at 31” in Length. Do you think bumping up to 75lbs will make my arrows too weak? I know I’ll just have to shoot it to figure it out maybe I’m just asking in you experience what’s ur thoughts?

@InsideOutPrecision

Жыл бұрын

At 31” and 75 lbs you’d be right on the verge of being too weak. Probably would notice much shooting field points, but broad heads might be a little erratic

@royleerobinson5

Жыл бұрын

@@InsideOutPrecision I appreciate it!

I shoot black eagle arrows. I ran them through my spine tester and then did your nock tuning test. I noticed that almost all the arrows shoot a bullet hole when the nock is 180 degrees rotated.

Can you also identify what you consider a Microshaft is?

@noneyabusiness4325

2 жыл бұрын

4mm or .166 INSIDE diameter is a microshaft

So I just solved my arrow problem kinda similar to what your saying. 30 inch arrow with 150 up front and my rest was kicked out to the left hard. I'm rh shooter. I added another 50 grains and I got a tail left tear which ended up bringing my rest in some. So my bow likes a softer spine. Could of dropped to 340 spine but I don't have the money for another dozen. Total weight up front now is 210 grains. 507 total weight

Process indeed. How could Geronimo hit the side of a barn? This is very educational and I thank you for it.

@ronaldeldred9673

2 жыл бұрын

Would you trust that 4mm for roosies???

@jeffrylotz138

2 жыл бұрын

I prefer the Victory RIP or VAP with a little weight. It'll go through two of them.

Will you consider Superdrive Micro 4mm for your arrows? Will it be considered an improvement over Axis 4mm?

X10 Protours have no stiff side.

@InsideOutPrecision

2 жыл бұрын

True! But nobody is going to hunt with pro tours

@allywilkeforsenate

2 жыл бұрын

@@InsideOutPrecision nobody has tried it yet.

@allywilkeforsenate

2 жыл бұрын

The glass is half full😀

What rest do you recommend and why?

You can use a lighter on the Victory TKO Rip arrows to remove the standard insert they use. I literally just took off two of them with a bic. Maybe 10 seconds tops to remove one.

Are those bows in cardboard boxs right above the targets you shoot at lol

@InsideOutPrecision

2 жыл бұрын

Haha no they’re empty

👍

@quantumeraser4833

2 жыл бұрын

Just fyi: You don't need - "A lot of Pro's say." Hope it helps

To the left , to left.. to the right, to the right..love your videos but this one was confusing like a Beyoncé song..

Do you ever offer classes??????? Like lectures?

@twodips4749

2 жыл бұрын

Pretty sure he does