Used this video to repair my dishwasher today. Thank you for posting! Took about 3 hours to replace after about an hour and a half to diagnose and determine that the issue was the user interface. Some of the plastic screw holders for the panel itself broke off but I put them back with some super glue.

Worked perfectly. Followed instructions step-by-step. Dishwasher back and running.

Thanks for this video, your call out for the dip switches was critical!!! Not all videos contained this imp. gem !!!

Jumper settings: instructions come with the new board. As shown on this video, They are 4 little plastic squares inserted into pins on the board. You then pull them out and arrange them according to instructions. It's a very simple thing to do. ..if you don't adjust them the board won't start.

@DuchessX23

Жыл бұрын

How are they adjusted, exactly?

Thanks, this worked for us. We also had lot of rust on the hinges. We think it was because the bottom seal (it's like a weather strip on a door) got really caked with crud and probably was spraying and leaking water. Once you take the door hinges off, this seal slides out easily and can be cleaned. Also the yellow foam around the port in the door was flaky and dried up on the side toward the door. I gently pulled the foam off, turned it over and put it back on, since the other side was in better shape. Maybe this will help you too.

I was stuck on how to remove the door without your video. Thank you!

Excellent instructional video! Helped me repair my dishwasher.

This video was perfect for us, however the jumper setting diagram was a bit unclear. We thought we had defective parts, so on our 3rd part (and after taking the dishwasher apart and putting it back together about a dozen times) we saw some comments about trying different pin settings and we finally got it to work! To us, it looked like the parts came set to personality 15 out of the box, but they weren't. All 4 pins had to get moved down toward the numbers to be set to 15 (ours was personality 10).

This video was spot on. Thanks for a job well done!

I followed your instructions step by step and it worked perfectly. It solved the issue. Thank you.

Thank you. Very helpful. The presenter was very good and very clear.

Awesome video! Just replaced my UI with help from your vid. Thank you so much!!!

Este como el resto de sus vídeos son excelentes todos los técnicos son de primera, gracias infinitas por compartir sus conocimientos a todos sus seguidores. 👍por ayudenmen soy solo travieso; necesito cambiar el termostato de mi nevera Whirlpool wrs49aktww dos puertas verticales. No encuentro video de la misma. Gracias infinitas. Saludos desde Ecuador 👍

Thanks for posting this video. It was excellent!

Thanks for showing how to put your fingers on the tabs to remove the control panel cover. I was about to attack it with a screw driver and a hammer.

Great video, you saved my dishwasher!

Thank you very much for this video I was going crazy how to take it apart thanks again

Thank you so much for this!

I was looking for a video like this. Awesome

Hi there, great video thanks. The information on how to change the jumper settings on the UI board is missing however. I get that the board comes with the settings configuration, but how to actually make those changes?

@thesqueedler

2 жыл бұрын

There are 4 jumpers there, and can be just pulled straight up. Then you can put them back on like in the diagram according to your model.

My numerical display has fallen down and to the right so that it is hard to read. Is repairing it simply of matter of accessing it and screwing it back on to the interface control board, or reattaching the control board to its mount?

The stainless steel models have two screws on each side that need to be unscrewed before you can separate the pieces

@stephenmesser8849

2 жыл бұрын

Thank you. I was trying to figure out what I was missing. This is it....no idea how many times i pulled on the hinges before googling again.

How do we adjust the jumper? I do not want to break anything.

@djjc76

3 жыл бұрын

It's per the instructions that come with the control module. There's a diagram that shows you how to adjust the jumpers per your dishwasher's model number.

Thank you!

Dishwasher was dead.. replaced the control panel board and its back on but beeping. Have a feeling replacing the board just reset it. But now it beeps every so often pointing to the user interface board. Ive ordered one of these but should I put back the old control board and send it back for refund, I'm still eligible to do so?

@appliancepartspros

3 ай бұрын

What is the model number of your dishwasher?

@pappascw

3 ай бұрын

@@appliancepartspros GDT580SMF4ES

I ordered a board and it came with no pins. Ugh

@gardenfairy351

2 жыл бұрын

Us too. Most places are showing this part as back order. Did you find where to order pins?

@bcar1ify

2 жыл бұрын

@@gardenfairy351 I just returned and ordered another and it came with pins

@gardenfairy351

2 жыл бұрын

@@bcar1ify Having trouble finding these boards. Its back ordered from multiple places.

@bcar1ify

2 жыл бұрын

@@gardenfairy351 yeah like most everything. It’s only going to get worse. Sad

Thank You!

Can you tell me what symptoms would cause this part to fail? My dishwasher seems to have no power. There is however power at the connector (where it is hard wired). The buttons don’t work and the display does nothing.

@thesqueedler

2 жыл бұрын

We found that not turning on and having the display do nothing was caused by the user interface control board in our case, but we learned it can also be the power control board which is on the bottom of the unit.

@tomloya7366

2 жыл бұрын

@@thesqueedler It would be good to show a couple things. 1. If you have the power control board hooked up and it has a solid green light, then it's probably the UI board. 2. if you are getting DC 13.5v - 14v on the #2 Black/Green to #5 yellow/blue, then the UI board is getting the proper power and it essentially is the UI board.

It seems a little difficult but considering I don't have a choice and labor being so expensive, I want to attempt to fix it. in order to assess if its worth the effort, I want to know how much UI board cost?

@robertbrandywine

2 жыл бұрын

Just google.

What models is this for? Looks different than my Profile PDW7880P

Anyone with the stainless steel inside cover: there are an addition 4 screws on the lower insde (2 per side) as well as 2 more screws underneath all the way up instead (1 per side). You need to undo all of these before you can pull off the cover. The 2 screws inside are a real pain. But when you pull the dishwasher out and tilt it, you can access these. They are further back inside in addition to the 2 on the bottom that he removes in the video. ALSO: there was no hinge pin holes on mine (to hold the hinges in place at an angle. Very strange. I had to pull the washer out and disconnect the hinges from the springs. This was actually very easy though. If you do it this way, you should remove the the door with rhe hinges attached before you remove all the screws. Good luck everyone

Thank you, but you didn’t show how to reprogram the jumper setting on the control board panel based on the model number/personality. I am installing myself. ☺️

@djjc76

3 жыл бұрын

It's per the sheet. Board comes programmed from the factory.

Hey sis! 👋

I have a GE washer and it's only about 3 years old. It's got the same problem. I find this crap unacceptable. It's a piece of junk!

@gwb0006

Жыл бұрын

The appliance tech who checked ours said that GE dishwashers have a lot of electrical problems. Kitchen Aid or Whirlpool are better brands.

Это русский

Awful engineering

@thesqueedler

2 жыл бұрын

I agree it's pretty cheap crap. Very disappointing. At least we could get it working again...

Thank you!