JUST FYI: 2 things that I do when I have stopped up lines. 1st, is to take a heat gun to the steel junctions, trying to keep the blunt of the heat off the rubber hose. This helps to begin the break down of the clog. 2nd, snake the lines out with something that should not cause damage to the rubber lines. I use an old "BRAKE or CHOKE CABLE," removed from the plastic sleeve. Take your cutters and cut the lead head off the end of the cable so there is just a chopped cable end. Then, spray some pb blaster or wd 40 into the brake line end that you are going to snake out. This will provide a little lubricant and will help clear the way as the brake cable snake begins to move into the line. Insert and begin to twist/push and continue to do that as you pull back about 1/2" in a poking method, until you have reached the clog and removed the debris and stoppage. Sometimes it can take a bit to get freedom, but this will work. You may have to pull the cable all the way out and snip the end again if it frays to much. The smaller the end, the easier it will penetrate the problem. I know this has helped me a lot of times. Enjoy!
@billyk8161
Жыл бұрын
brilliant! thank you!
@luckydog-287 Жыл бұрын
Great video, 9 years later. Thank you very much!
@motocharles420811 жыл бұрын
I'm that guy who says you should always tear down and inspect the MC and calipers on a new-to-you vintage bike and replace the old rubber lines with stainless steel. Manufacturers used to specify replacing the rubber lines every two years, so a 30 year-old bike still sporting the original lines is about 28 years overdue! But like you said, to each his own. Thanks for the video!
@hi931311 жыл бұрын
I don't even have a motorcycle but I really enjoy watching your videos.
@ricksanchez35446 жыл бұрын
Loved the vid, got to clean the lines on my 1980 kz750H ltd. They were all blocked before the splitter, a good paper clip and air worked just fine. Now waiting for break fluid to come in and hopefully i put the banjo on the master cylinder the right way since theres no notch it belongs in.
@KEVRPH11 жыл бұрын
Max, I like your resourcefulness! If you are worried about riding around on 30 year old parts and you can afford to buy everything new you should just get a new bike.
@DanTheFordFixer11 жыл бұрын
good vid, I swap brake parts around all the time, if they fail you still have a rear brake to ride home on. early honda magna master cylinders are the strongest I have found if you want stiff brakes with any line.
@jimkessler9997 Жыл бұрын
Your video was finally what I was looking for thank you.
@rbahr82142 жыл бұрын
Very good information. Used it on my ATV
@TheDrunkardHu11 жыл бұрын
awesome info! i can already tell that these are going to be hugely helpful videos! any plans of making this into a playlist?
@bobbyfisher62784 жыл бұрын
THANKS for making this
@ramsn197111 жыл бұрын
I'm going through some old brake lines on my 1981 Suzuki GS750. What I've done so far is bathe them in 10 parts to 1 water and phosphoric acid. This will not harm the plastic and it does loosen up the gunk inside. After that I use the strand of an old sacrificial clutch wire and slowly go in as far as I can. I then use a combo of the clutch wire strand, brake cleaner and air compressor till the wire goes in more than half on each side. You should be good to go after that.
@yoyimarti28643 жыл бұрын
exactly video I needed !!! THANXXXX
@mrmaxstorey11 жыл бұрын
Yeah I blew out the caliper reservoir in this video, but I only take the thing apart if its seized. I love the entire XT line, every single model. Can't go wrong!
@mrmaxstorey11 жыл бұрын
Never been on one myself, but it looks like a classy machine. Should suit you well.
@Jeremysw211 жыл бұрын
hey max, what do you think of the Suzuki tu250x? i'm thinking of picking one up as a first bike for commuting to work on. flat land ~8 miles each way. Love that vintage style
@dportz9111 жыл бұрын
I may be able to :D thanks, I hadn't thought of that :D I'll let you know how it turns out :)
@mrmaxstorey11 жыл бұрын
There should be a small rubber diaphragm underneath the master cyl cap. Is it there, installed appropriately, and undamaged?
@mrmaxstorey11 жыл бұрын
I have some playlists on the channel, this will be added to the brakes playlist. I used to have a lot more but the youtube reorganization cut me down to only 9 playlists
@r3dhorse6 жыл бұрын
Honestly just throwing on some braided lines would take around the same time. Cool video though. Might use it for the rear brakes on my SV650.
@timothytime417610 жыл бұрын
Thank you
@mrmaxstorey11 жыл бұрын
You can take it apart, free it and clean it out, but at the least you will probably need a rebuild kit because the seals are likely to be toast. Thats why I just replace them
@BrianNguyen-jk5tu11 жыл бұрын
The plunger coming off of my master is stuck completely depressed. Are there any good tricks to free it up?
@mrmaxstorey11 жыл бұрын
Can you get the wheel of a dremel in there to dig the slot a little deeper?
@dportz9111 жыл бұрын
Hey, Max. I know this question isn't about brake bleeding problems, but on my Suzuki bandit I can't get the brake pad screws off because the previous owner stripped them. I was wondering if you had any ideas. They are what hold the brake pad pins in and are flat head screws. Thanks, David. Great video, by the way :)
@mrmaxstorey11 жыл бұрын
thanks bud
@zworldwarfare11 жыл бұрын
have you ever had a front brake that built up pressure over time?. i cant find anything that talks about it. so i thought to ask you. if i leave it for a few days and jack it up. the front tire barely moves. when i undo the bleeder. fluid comes out and front tire moves, wait a few days and jack it up and the front tire is slow again. any ideas?
@bpr154
4 жыл бұрын
Mason Kelly 6 years too late, but it's seized pistons in the caliper. Take it apart and check if the piston is corroded, if so replace
@mrmaxstorey11 жыл бұрын
No fronts? You have bigger balls than I do. The only bike I ever rode that didn't have front brakes was that squirrely KZ400 chopper, and it was fishtailing all the time
@timothytime417610 жыл бұрын
Rear brakes not working. When last ridden, less than a month ago, brakes worked just fine. It's been parked in non-heated but enclosed garage. rear pedal goes down with very little pressure. Tried bleeding the brakes. A lot of air coming through. But even so it's only building up enough pressure to push more fluid out. Do you think it's the master cylinder or the brake pad cylinders? Front brakes work fine.
@mrmaxstorey
10 жыл бұрын
Check for leaks, cracked hose, banjo bolt not tight, etc
@r3dhorse
6 жыл бұрын
Probably a leak either around the master cylinder or one of the banjo bolts.
@mrmaxstorey11 жыл бұрын
Hats off to you then, I don't fault you at all
@mrmaxstorey11 жыл бұрын
Haha I like it
@sergedenovo2389Ай бұрын
Danm! I don’t have a compressor! Someone loan me yours, fools! 😆 Be well, and be safe, goys. Keep rubber side down!
Пікірлер: 37
JUST FYI: 2 things that I do when I have stopped up lines. 1st, is to take a heat gun to the steel junctions, trying to keep the blunt of the heat off the rubber hose. This helps to begin the break down of the clog. 2nd, snake the lines out with something that should not cause damage to the rubber lines. I use an old "BRAKE or CHOKE CABLE," removed from the plastic sleeve. Take your cutters and cut the lead head off the end of the cable so there is just a chopped cable end. Then, spray some pb blaster or wd 40 into the brake line end that you are going to snake out. This will provide a little lubricant and will help clear the way as the brake cable snake begins to move into the line. Insert and begin to twist/push and continue to do that as you pull back about 1/2" in a poking method, until you have reached the clog and removed the debris and stoppage. Sometimes it can take a bit to get freedom, but this will work. You may have to pull the cable all the way out and snip the end again if it frays to much. The smaller the end, the easier it will penetrate the problem. I know this has helped me a lot of times. Enjoy!
@billyk8161
Жыл бұрын
brilliant! thank you!
Great video, 9 years later. Thank you very much!
I'm that guy who says you should always tear down and inspect the MC and calipers on a new-to-you vintage bike and replace the old rubber lines with stainless steel. Manufacturers used to specify replacing the rubber lines every two years, so a 30 year-old bike still sporting the original lines is about 28 years overdue! But like you said, to each his own. Thanks for the video!
I don't even have a motorcycle but I really enjoy watching your videos.
Loved the vid, got to clean the lines on my 1980 kz750H ltd. They were all blocked before the splitter, a good paper clip and air worked just fine. Now waiting for break fluid to come in and hopefully i put the banjo on the master cylinder the right way since theres no notch it belongs in.
Max, I like your resourcefulness! If you are worried about riding around on 30 year old parts and you can afford to buy everything new you should just get a new bike.
good vid, I swap brake parts around all the time, if they fail you still have a rear brake to ride home on. early honda magna master cylinders are the strongest I have found if you want stiff brakes with any line.
Your video was finally what I was looking for thank you.
Very good information. Used it on my ATV
awesome info! i can already tell that these are going to be hugely helpful videos! any plans of making this into a playlist?
THANKS for making this
I'm going through some old brake lines on my 1981 Suzuki GS750. What I've done so far is bathe them in 10 parts to 1 water and phosphoric acid. This will not harm the plastic and it does loosen up the gunk inside. After that I use the strand of an old sacrificial clutch wire and slowly go in as far as I can. I then use a combo of the clutch wire strand, brake cleaner and air compressor till the wire goes in more than half on each side. You should be good to go after that.
exactly video I needed !!! THANXXXX
Yeah I blew out the caliper reservoir in this video, but I only take the thing apart if its seized. I love the entire XT line, every single model. Can't go wrong!
Never been on one myself, but it looks like a classy machine. Should suit you well.
hey max, what do you think of the Suzuki tu250x? i'm thinking of picking one up as a first bike for commuting to work on. flat land ~8 miles each way. Love that vintage style
I may be able to :D thanks, I hadn't thought of that :D I'll let you know how it turns out :)
There should be a small rubber diaphragm underneath the master cyl cap. Is it there, installed appropriately, and undamaged?
I have some playlists on the channel, this will be added to the brakes playlist. I used to have a lot more but the youtube reorganization cut me down to only 9 playlists
Honestly just throwing on some braided lines would take around the same time. Cool video though. Might use it for the rear brakes on my SV650.
Thank you
You can take it apart, free it and clean it out, but at the least you will probably need a rebuild kit because the seals are likely to be toast. Thats why I just replace them
The plunger coming off of my master is stuck completely depressed. Are there any good tricks to free it up?
Can you get the wheel of a dremel in there to dig the slot a little deeper?
Hey, Max. I know this question isn't about brake bleeding problems, but on my Suzuki bandit I can't get the brake pad screws off because the previous owner stripped them. I was wondering if you had any ideas. They are what hold the brake pad pins in and are flat head screws. Thanks, David. Great video, by the way :)
thanks bud
have you ever had a front brake that built up pressure over time?. i cant find anything that talks about it. so i thought to ask you. if i leave it for a few days and jack it up. the front tire barely moves. when i undo the bleeder. fluid comes out and front tire moves, wait a few days and jack it up and the front tire is slow again. any ideas?
@bpr154
4 жыл бұрын
Mason Kelly 6 years too late, but it's seized pistons in the caliper. Take it apart and check if the piston is corroded, if so replace
No fronts? You have bigger balls than I do. The only bike I ever rode that didn't have front brakes was that squirrely KZ400 chopper, and it was fishtailing all the time
Rear brakes not working. When last ridden, less than a month ago, brakes worked just fine. It's been parked in non-heated but enclosed garage. rear pedal goes down with very little pressure. Tried bleeding the brakes. A lot of air coming through. But even so it's only building up enough pressure to push more fluid out. Do you think it's the master cylinder or the brake pad cylinders? Front brakes work fine.
@mrmaxstorey
10 жыл бұрын
Check for leaks, cracked hose, banjo bolt not tight, etc
@r3dhorse
6 жыл бұрын
Probably a leak either around the master cylinder or one of the banjo bolts.
Hats off to you then, I don't fault you at all
Haha I like it
Danm! I don’t have a compressor! Someone loan me yours, fools! 😆 Be well, and be safe, goys. Keep rubber side down!