I pick up these washers and dryer setting by curbside for throw a way. Have done this for about 1 year. I am 84 years old. So far, I have been able to repair all. Then I give them away .This is my way to help someone in need especially single moms or someone needy. This becomes a blessing for us both. I deliver and set up all at no cost. Keeps me active and helping others in need. GOD has blessed me. Praise GOD in the highest !

@HarperandKnowles

9 ай бұрын

That is a wonderful mission. I hope my videos help in your repairs. Thanks for watching!

After troubleshooting and thinking it was the transmission I saw this video, thank you! It was my tub hub

@HarperandKnowles

3 ай бұрын

Glad it helped! Thanks for watching!

Very helpful an informative, thank you

@HarperandKnowles

6 ай бұрын

Thank you for watching!

@R.Akerman-oz1tf

3 ай бұрын

@@HarperandKnowlesThis machine is so very clean(spot rust).

so far the Speedqueen washer I have has been trouble free in the 5 years ive had it.. hopefully it keeps on truckin

@HarperandKnowles

11 ай бұрын

It should be good for another 20 years or so. Thanks for watching!

@R.Akerman-oz1tf

3 ай бұрын

@@HarperandKnowlesHands down, the only vid worth watching. Question on My "wash-plate" Kenmore; Intermittent drive motor. Normal cycle or test mode: might work or not. Old cap metered good/new cap-still no change. Possible bad relay on Motherboard? What say You. Help is appreciated, Thanks so much.

@R.Akerman-oz1tf

3 ай бұрын

Just noticed Ur Louisiana Guy w/books. Sounds interesting to Me.

I have a Maytag bravos. It was occasionally making a grinding sound when starting to agitate. Then it just recently stopped spinning. I removed the wash basket to check the drive hub which was indeed bad but my problem is, when I removed the wash basket, the tube that it’s connected to came out with it and now I’m stuck and don’t know what to do. I tried just putting it back together like that but it’s not working.

@HarperandKnowles

3 ай бұрын

If your spline shaft is broken you'll have to change the gear box. Thanks for watching!

Wow, at 36:22 you skipped the video forward. That is the exact point of the cycle where my machine fails to go into spin cycle. My agitator turns a few turns left then right, Unbalancing the load. Then tries to spin, causing the machine to violently jump all over the laundry room and eventually go to "complete cycle" never going into high speed spin. The load is completely soaked. My Diag codes are F7 E7, I think it is a Splutch cam problem. Thanks for the video

@HarperandKnowles

Ай бұрын

You are very welcome. Thanks for watching!

I have an older Maytag and it spins but it doesn’t spin fast enough to get the water out of the clothes…they are still wet and it only spins for a couple of minutes and then spins again…any ideas? Thanks for any help

@HarperandKnowles

2 ай бұрын

You may need a new motor. If it spins then stops then comes back on after the motor has a chance to cool down then your motor is failing. Thanks for watching!

Have a amana washer i bought feb last year BRAND NEW. Have had to repair 3 times. So frustrating and exhausting 😢

@HarperandKnowles

11 ай бұрын

I’m sorry to hear you’re have trouble with your washer. You should get a Speed Queen TC5 they are the best! The Best Washing Machine You Can Buy In 2023 kzread.info/dash/bejne/o6CfxtqQlrfAhto.html

Do people ever remove the blue plastic protection on their washer/dryer control panel? Whenever I come across laundry repair channels or random laundry videos, I've noticed a lot of end users don't remove the blue film on their machines after years of use🤣😆.

@HarperandKnowles

4 ай бұрын

I buy a lot of used machines and that stuff sticks down almost permanently after a few years. It’s hard to remove but once I paint the frame and peel that stuff away it looks like a new machine! Thanks for watching!

awesome repair!!! do you ever get any of those OLD! whirlpools? i wish I could find one.. like from the 60s and 70s?

@HarperandKnowles

11 ай бұрын

No, those are considered antiques now. I get a few from the late 80’s and 90’s though. Mostly worn completely out!

@eldoradoboy

11 ай бұрын

@@HarperandKnowles that system from the 80s always seemed wierd.. somewhat simple but even more clunky than the "wigwag" design...

@jaycole3768

11 ай бұрын

@@HarperandKnowles Have a question for you..I used a the dryer yesterday and worked just fine..using it today and the drum keeps spinning without the dryer being on..I have to keep the door open..would you know what would cause that?

@HarperandKnowles

11 ай бұрын

You failed to mention the make and model but I’ll give you my best guess. So if it stops when the door is open but starts right up when you close it I’d think the start button is stuck down. Just guessing but if you open the timer you might discover some stuck points if the start button isn’t the problem. On a GE product, (includes Frigidaire) I’d suspect a stuck start button too. Also be sure your door switch is working properly. If it continues to run but the timer doesn’t move then it’s the timer motor or something preventing power to the little motor. Thanks for watching!

@jaycole3768

11 ай бұрын

@@HarperandKnowles Samsung. There's no model number sticker on it. 2014 design

Got the same washer. Making a nose while the tub is washing. But noticed the tub does not spin while rinsing. Any help would be appreciated.

@HarperandKnowles

2 ай бұрын

The tub hub is probably your problem. Thanks for watching!

@JuanPerez-sj8gg

2 ай бұрын

I thought it was the clutch. Changed it but housed the lid lock. To see its motion. Agitates well. But when draining the tub wants to spin but dont move.

Grinding sound in spin mode. Not spinning. Actuator replaced. Program recalibrated.

@HarperandKnowles

10 ай бұрын

A grinding noise during spin is never a good sign. It’s almost always a symptom of failing bearings. Depending on your model it could be a failed tub hub. But most likely your bearings are failing. Look for evidence of rusty water spots on the bottom near the center. Failed bearings usually mean the machine has ended its useful life. Models like the Cabrio with a direct drive rotar/stator system can be repaired. See this video. Whirlpool Cabrio Spin Noise & Rusty Spots Under The Machine Solution Guide kzread.info/dash/bejne/kYas0LeMk7eaYKw.html. Thanks for watching!

I didnt know that those metal couplers fit those types of machines. I been ordering and using the plastic ones. I hate the plastic ones

@HarperandKnowles

11 ай бұрын

Yeah, I quit ordering the plastic ones too. Even if you change one it doesn't last more than a month or so and the customer gets mad at you.

@jaycole3768

11 ай бұрын

@HarperandKnowles yep. I had that issue a few time.

@jaycole3768

11 ай бұрын

@HarperandKnowles I have to lg washers that I can figure out. One spins and agitates. But the agitation is very delayed and the wash cycle doesn't count down. The other one won't spin. I changed the locks stators and actuators. And they don't have hull sensors. Any idea what I'm missing

@HarperandKnowles

11 ай бұрын

Probably the control boards on both. If they have the same control boards why don’t you swap boards on one and see if the issue transfers over with the board. Then you’ll have your answer! Let me know how that goes.

@jaycole3768

11 ай бұрын

@HarperandKnowles control boards are different. And I have 3 more control board but there all different. I should of save the wire harness