*Construction seemed sturdier than other units I considered **MyBest.Tools** Noise level was reasonable. Good pressure and cfm capacity for a small reasonably light compressor.*

*This does exactly what I was wanting **MyBest.Tools** Price was fantastic, lower than Harbor Freight-and it included hose and attachments, and IT IS MADE IN AMERICA, unlike Harbor Freight*

Thank you for posting this video! Was only getting up to 44 psi and about to go spend $300 on a new one. Only spent $19 to fix my Campbell Hausfeld 26 gallon. New part was $17 and I used a $2 angled L bracket from Lowes and attached to the broken bracket. Working good as new! Thanks for saving me money, trash from the landfill, and large companies from profiting from poor designs. Flex line would be the best option.

I have a red 22 Gallon 5hp version of you air compressor. Changed the tube n it fixed it thanks to your vid

For awhile my compressor was filling up to 90 psi. Now it only goes up to about 25 psi. Now I know what to check for when I take it apart this weekend. Thank you for making the video.

@vxmine

7 жыл бұрын

Ty. Mine just started doing the same thing. Only fills to 25 psi and when I start using air it never "kicks in" to fill the tank. Did you figure out what was wrong with yours? I'll probably tear min apart this week.

Thank you for the video. I inherited a similar sized Husky. Previous owner said it wouldn't build pressure. I'll check this week for cracks. I did change out the drain valve. So that's holding what pressure it does build (20-30psi).

Thanks for the insight. Fixed me right up. Stay Blessed

Great video! Helped me find the same issues on my compressor! Thank you!

A friend had the same recurring problem with an Ingersoll Rand. We solved the issue by using our own copper tubing and leaving a coil of tubing in the line to absorb vibrations.

@papawnanasaveslovesnlife9530

5 жыл бұрын

yep you cant really run it straight to it like that due to vibration put a loop in the copper tubing

That rocked, thank for posting.

Thanks a lot for your video, it helped me a lot to fix my compressor.

@fredklosterman7279

2 жыл бұрын

Hello hope you are doing well. How do I send you a message? I have a question on my 33 gallon 1.75 horsepower 150 psi Husky Air Compressor. Model No. WL660800AJ. Thank you very much. Sincerely Fred Klosterman

Thanks for Vid - the plastic tube to the pressure switch was my problem.

Thanks for the video. I'm helping a buddy fix his. The copper tube is split lengthwise on both sides after 20 years of occasional use.

@J20Jeepster

Жыл бұрын

Thanks for watching!

EXHAUST TUBE!! I have been looking for that same thing online and couldn't find it anywhere. Now I know what to shop for. Thanks man. Mine was cracked

@Dansk55

4 жыл бұрын

Ok so after some research I found that these Husky tubes keep cracking under pressure. I will likely replace with a stainless steel flexible tube. aircompressorpartsonline.com/transfer-tubes-nylon-tubing-steel-braided-transfer-tubes-c-25_294_434.html

@J20Jeepster

4 жыл бұрын

@@Dansk55 good idea! Thanks for watching!

Thanks for that information I replace mine with copper three years ago

How do I get the cover of the Husky 17 gallon air compressor

Well done!

do u kn wher I can get motor for this same air comperssor

Cool deal kid!!!!! I’ll be giving my compressor this try. Thank you and be well. I liked and subscribed 👍🏼😉

@J20Jeepster

5 жыл бұрын

Thank you!

Shot in the dark, but I’m having an issue with the same style compressor.. but my issue is with the black tube that’s connected to exhaust to leading to front of motor.. I started it the other day and it sounded like air leaking while running and it will not fill past 100lbs .. any guess on how to fix?? I can’t find anything

From 9:05-9:10 you show the tank gaining pressure. Was that time-lapse, or should I expect to see that kind of rate of recharge in my Husky y6010 25-gal tank?

Hey bud, simple question, what do you do to maintain the best performance of it? Does it need a lubricant on the piston or need the poston's plunger to be replaced? Bkught an old one that works but maybe a little slow. Thanks bud!

I had the same broken bracket and I had to weld that back into place.

Thanks so much for the video. Great job on the bracket!! Where do I go for the part, or is it an Amazon thing?

Mine makes a electrical noise like the motor is not engaging when you turn the switch to the on position any pointers its a husky 26 gallon electric

Thank you sir

I have a silent compressor by husky and it takes a long time to fill up can you give me a tip on what to do because it is to fill a lot kwiker

I have the same compressor,and I think I have a problem with piston,do u know where to get parts for it?

Exactly what happen to mine. The bracket broke, that caused the copper pipe to crack.

You can buy industrial flex air hoses and fittings instead of the copper but would need to match up fittings and perhaps tap the head.

So mine was just a dry rotted rubber line between main rail and adjuster valve. Replaced with some random tubing and it’s fixed

What was the problem with the compressor in the first place? What symptom did you have?

would this help if it takes 15 minutes for the compressor to only fill to 75 psi out of 150 psi?

was it louder before you fixed it

Great video for the exhaust tube and motor mount. Do you have anything that shows replacing the pressure switch on this same model of Husky compressor? Thank you.

@JeremiahL1616

11 ай бұрын

Anything on the unit with black cover and fan inside? My keeps popping and wont stop and run when low on air

thank you so much that's exactly what my problem was but I have another problem it got up to 170 PSI and never shut off what do you think could be the problem or do you think the problem was I had a crack in the exhaust I haven't got the new tube in the mail yet

@J20Jeepster

4 жыл бұрын

Yeah, it's not building enough pressure to activate the pressure switch with that crack in the tube.

I have a shop force air compressor, After I turn it on and builds up some pressure oil sprays out of the oil filler cap. I took the valve apart and checked the strips of metal and metal gasket and they don't look warn or broken. sf2500 is the model and I wonder what it could be? thanks,

@elmerfudd5925

6 жыл бұрын

tom purcell just a thought. Sounds like blow by. Too much crankcase pressure. Bad rings maybe. Trying to remember from my car repair days. Same principle. Sorry. Best I can do.

Nice fix. Couldn’t you also just have welded the old bracket?

Hey boss. What's the black tube coming from the tank inlet valve, for? I just bought a used system and it's missing this black tube and it's venting the tank, so it's not able to pressurize the tank. The tube at 8:36. Thank you.

@J20Jeepster

5 жыл бұрын

That's the tube that goes to the pressure switch. It lets the switch know the pressure of the tank so it knows when to shut off.

Boom! The nut was loose on my hose, simple.

@J20Jeepster

4 жыл бұрын

Nice!

Where did you find the rubber ferrules for the exhaust tube fittings? Does any other material work like O rings or brass ferrules? I have the same compressor with the same problem plus another gremlin or two.

@KCPestAwayOlathe

8 жыл бұрын

Thanks. It appears that my tube is OK, but the ferrules (or whatever those rubber things are called) are not and its not holding pressure. I picked up some O rings and thought I would give those a shot.

@KCPestAwayOlathe

8 жыл бұрын

I think I am going to have to order the pipe kit. The O rings by themselves didn't do the trick. I ended up taking the original worn out gaskets and putting those back in, then backed those with O rings for a tighter fit. It holds pressure now but I believe that the O rings will fail soon due to the heat. I could be wrong and this could last quite a while but I'm not holding my breath. Thanks for your video and information. At least I know now that this compressor is repairable and not heading to the scrap yard yet!

Where did you find the motor for this?

I need this part can someone direct me to it I can't find it please help !!!!

Best solution, change to a high preasure rubber hose..

how do you change when the compressor turns off on the campbell hausfeld

@J20Jeepster

5 жыл бұрын

You don't. It's a pre set switch.

I have an identical compressor. Do you know if it takes any oil? Or is it oil free compressor? Can find any info on it.

@whatfreedom7

4 жыл бұрын

No they are oil free. I have the same one. These are maintenance free so you really don’t have to do anything other than drain the water every now and then and maybe a belt eventually. You still need to oil your air tools though.

I see some compressors using some type of rubber looking hose. Maybe even a small hydraulic type hose would cure the problem permanently. ???

I just picked up a compressor very similar to yours(32 gallon husky/ch 150 psi) and it won't build pressure past 60 psi. Any help you can give diagnosing would be appreciated. Thanks!! After further inspection I found the problem. the pipe is split in several places lol. Can I use copper tubing or is it supposed to be a certain metal?

@derekbagwell6933

6 жыл бұрын

Chris Thompson thats ingenous! Do they not make the springs meant for bending copper tubing anymore?

@whatfreedom7

4 жыл бұрын

I had the same issue. It got louder and was running and running and running for longer than normal periods so I would shut it down. I had a cracked pressure hose on the inside of the bend. I made my own and was good again.

Helo I have a problem my compressor don't come back on the 2time to reload

Excellent Video, will look for this tomorrow. My Compressor is not building pressure at all and its the same one. Just bought a new piston/ring set and still not building pressure (previous ring was apart in pieces). Someone said it may be a valve but I have no idea where to look for it. Anyone with any input I would greatly appreciate it. Thanks.

@whatfreedom7

4 жыл бұрын

Old post but mine had a crack on the inside of the bend on the pressure line. Maybe it will help someone else.

@scottl5910

3 жыл бұрын

@ Al Zedder it might be the reed valves in the compressor head. Search reed valves that will give you an idea of what to look for. Good luck!

@Triggerman2505

3 жыл бұрын

@@scottl5910 ​ Thanks, I ended up fixing it, but it was so long ago, I honestly forgot what I did :)

wat state are u in

what was your problem? not building pressure?

@Aneocs

8 жыл бұрын

Thanks im going to check mine this weekend lord willing. Mine wont go passed 25

Mine builds air but won't a second time or sometimes it will build then rebuild twice and then stop working until empty and unplugged for a few minutes then after plugging back in it works. Amy ideas?

@J20Jeepster

4 жыл бұрын

Sounds like it's over heating. I would still check this hose because if it takes too long to build pressure back up it will overheat and shut down.

@Lifesabishi

4 жыл бұрын

@@J20Jeepster I just finished disassembling and reassembling it after checking it for cracks

Where a reset button for this model compressor

Same identical problem. Who would have thought ?

My compressor starts working and builds pressure up to 150psi but sometimes during work it will not start and won't keep tank charged. Sometimes it turns on only for a few seconds then goes quiet. Sometimes I hears something that it wants to start like air going somewhere through the pipe for about 2 second and then quiets and stays like that. Fails to keep up pressure in tank when I use it. Pressure goes low as 50psi but compressor doesn't start. Then I had to open drain valve to release remaining air pressure in the tank. Disconnect it from AC power for few minutes and it starts working again build up to 150psi again. I don't hear any air leaks. What could be wrong?

@J20Jeepster

2 жыл бұрын

Sounds like the pressure switch might be going out.

@extragetit5876

Жыл бұрын

Did that work? I have the same problem

I need help fixing my air compressor

@swift4311

3 жыл бұрын

Has it fixed yet?

Mine starts and stops every few seconds and the pressure stays the same

I don't see how your pump is vibrating soo 5:42 bad to break the bracket and the tube.

My compressor is getting really loud at 60 psi hard to explain but it sounds like it's struggling after that point to reach full capacity...

@creativeminds51

7 жыл бұрын

TheJ20jeepster ok so should I replace tube first then go from there

@creativeminds51

7 жыл бұрын

Come to think of it when I cut on I placed my hand by that area ,and I could feel some blowback were those horizontal plates are

@swift4311

3 жыл бұрын

What kind husky?

@creativeminds51

3 жыл бұрын

kevie khidir yes

No usan aceite este tipo de compresores

they could've done that connection with a flexible or corrugated tube, but that would just make it last longer.

@J20Jeepster

5 жыл бұрын

My thoughts exactly. Couldn't find a flexible aftermarket either. 😐

@stephanieengstrom8025

4 жыл бұрын

@@J20Jeepster I went to a place called All Hose or House of Hose in L.V. they make custom hoses wasn't cheap 28$ but will outlast the Comp itself

@J20Jeepster

4 жыл бұрын

@@stephanieengstrom8025 Good to know, thanks for the comment!

Anybody have an issue with the static motor im assuming. The unit on right side with blade on outside? This one keeps popping the motor reset. It will run upto 100 lb and pop and then u wait 10min and try again. I can upload a video

@JeremiahL1616

11 ай бұрын

It has the black cover over it next to tube

Did you see the missing bolt just to the right of where your strap broke? (I’m not gonna look to see if someone else pointed it out, just trying to be helpful- not make a career out of it;))

i thought something was wrong with it because it cuts off at 80 and most compressors cut off at 125

@J20Jeepster

5 жыл бұрын

Sounds like you have a small leak. Probably in the tube shown in this video. It is supposed to shut off at around 125, but it will over heat and shut off before that if the pressure never builds.

@foxybrown2

5 жыл бұрын

@@J20Jeepster where can i buy the whole cut off valve and switch?

Wow a reduction belt drive on the crankshaft so it can run with a punk ass little motor ... so that's how they do that one !

@whatfreedom7

4 жыл бұрын

That’s how a lot of the maintenance free motors are. The pistons are tiny too. I have one and they are inadequate in my opinion.

I woulda tried soldering that crack in the tube from the inside.

@whatfreedom7

4 жыл бұрын

Bad idea. If I remember right they have a little rubber seal on the ends.

Ignorant question! Is there oil required for this

@J20Jeepster

5 жыл бұрын

No, It doesn't have a place to service it with oil.

You made that compressor your ***** !

phx az

Hmmm i wonder what the issue was since you never said