Working together like old times, good to see yous having a laugh and not working to hard Keep up the content mick

@TheSilverFoxDoesStuff

3 жыл бұрын

Thank you. We had fun doing it 😀

Hi Tom, thanks for watching. Yes they were custom made, but I'm pretty sure it'll be a standard size.

Doors look fab! Will have to keep John in mind when we come to replace our windows and doors - which are about ready to fall out of the house 😅

@TheSilverFoxDoesStuff

3 жыл бұрын

If they're falling out, that would make the job easier lol

@moyaterry8493

3 жыл бұрын

@@TheSilverFoxDoesStuff 😆😆😆

Great video sir. Worthy of far more views. The chemistry between the two of you is great. Can I ask, do I need to support the brickwork with acrow props to convert a window to French style doors. Many thanks in advance for your help 👍

@TheSilverFoxDoesStuff

3 жыл бұрын

Hi, thanks for the lovely comments. I will ask the expert John, and get back to you :)

Hi great video. I'v just had french doors fitted and when I close the doors (lock one door). When I just close the other door just with the latch (not lock) the bottom of the door closes but there is a gap at the top of the door, so when I pull the handle up to lock the door, the top of the door is pulled in, therefor closing and opening the door takes quite a bit effort. I suggested to the fitter this was not correct, When I only close the offending door, again the bottom touches the frame and the top is about 1 cm from the frame, could you advise please. Thank you.

@TheSilverFoxDoesStuff

2 жыл бұрын

Yes that is wrong and needs sorting out. We had to adjust the hinges again after a few weeks, because I was having similar problems. He totally needs to come back and adjust the hinges. It's not a hard job for him to do. Glad you liked the video.

@toddbrady8540

2 жыл бұрын

There will always be a bit of movement on the top and bottom of doors when only on the latch, Upping the handle engages the 7 point locking system and makes doors tight and secure, 👍

@JIMMIX7

2 жыл бұрын

@@toddbrady8540 Yes i understand that, but when the bottom of the door touches the bottom of the frame first by quite a bit, it means when pulling the handle up the closing door has to twist to close the door tightly. I notice when opening the door just a slight bit, the hinge side of the door has opened further at the top than at the bottom, This door is higher than the other although the gap outside when closed between the two doors is equal. (if this makes sence) . I have lost confidence in them. Most of the windows I had fitted were badly scratched and many fingerprints (hand prints) are in the inside of the glass when the 2 panes of glass were assembled at the factory. 5 glass panels needs replaced. The door handle is very hard to open, and has to be pulled up with quite a bit of force to engage the locking. Not a good start !.. Thank you for your reply.

How did you manager to get the doors to exactly fit the gap? Are they custom made for your gap?

@foxystravels

Жыл бұрын

Hi Tom, thanks for watching. Yes they were custom made, but I'm pretty sure it'll be a standard size.

@TheSilverFoxDoesStuff

Жыл бұрын

Yes custom made.

I been a Glazier for over 25 years and this is a shambles, ignore all you see here good ppl and get a FENSA registered qualified Glazier to do the job not hiawaffa and tonto👍

@TheSilverFoxDoesStuff

2 жыл бұрын

You're a happy chap aren't you.The doors have been in since April and work just fine. John has been fitting these for well over 25 years, and has never had a problem.

@TheSilverFoxDoesStuff

2 жыл бұрын

I wasn't touting for business by the way lol

Why the fuck are you wearing headphones.

@TheSilverFoxDoesStuff

3 жыл бұрын

Please don't swear, it's naughty. But do you mean ear defenders ? Do I really have to tell you ? It's not rocket science is it ?