How to diagnosis multi-outdoor-unit error using monitor mode 14 | Daikin VRV3
Brand : Daikin VRV3
model : RXQ14PAY13 RXQ10AYM
Error code: E2
Remote controller display = E2
Applicable Models
VRV3, VRV3-Q
Method of error Detection
Failure is to be detected by using leak detection PCB assy.
Error Decision Conditions
Leakage is detected under the conditions outside of the scope of high pressure switch operation.
Supposed Causes
Defective compressor.
#bonmj #daikin #vrv
Пікірлер: 66
finally i get a great teacher thank you so much sir thanks from india
@BonMj
2 жыл бұрын
Welcome
Oh my God... this was The Big Party of The Faulty Thermistors! 🥳 One after another!
Hi sir bon , i love your explanation . 🙏 . Im beginner in Daikin VRV . Say hello from BALI
@BonMj
2 жыл бұрын
Thanks
Great job brother
@BonMj
2 жыл бұрын
Thanks
Hi, it's a very explanatory video again bro.👏👏👏🙏
@BonMj
2 жыл бұрын
Thanks
Very nice sir,from India, ,
@BonMj
Жыл бұрын
Thanks 🙏
Thx's for ur explaination :)
@BonMj
2 жыл бұрын
Welcome
Bon sir lot of thanks 💓
@BonMj
Жыл бұрын
Welcome
Hello sir bon😍I like you ..i’m from Cambodia
@BonMj
Жыл бұрын
Thanks
very nice teach....
@BonMj
Жыл бұрын
Thanks 🙏
Good job
@BonMj
2 жыл бұрын
Thanks
Thanks for your update sir i would like to expert Mitsubishi outdoor function settings video sir
Hi everyone, I've working on Daikin VRV for many years. I have one question, why does the Daikin VRV have a lot more problems with their systems than any other equivalent VRF Systems, like Mitsubishi Electric, Mitsubishi Heavy, Fujitsu, Toshiba, plus many others. Just the parts department of Daikin are so extensive and very busy., especially here in the UK 🇬🇧. One example, replaced many, many compressors for Daikin VRV, but for other manufacturers, just a few in my time. What I have personally found that if a Daikin VRV System is professionally installed and commissioned and well maintained afterwards, there will be a lot less breakdown and thus less repairs. We have installed Daikin VRV Systems and they have been running trouble free for many years. Anyway, it keeps me very busy especially working on Daikin VRV Systems.
In this case,need to bypass the master unit?
Good jop
@BonMj
Жыл бұрын
Thanks
Please one video uj 01 urgent explain daikin vrv 4
Dear sir, I am Arunachalam from Chennai, Tamilnadu, India. Glad to chat with you. Now I am servicing rxyq 18 pay6 +rxyq 18 pay6 +rxyq 10 pay6 Daikin VRV. rxyq18pay6 is a master. When on the unit rxyq 10 pay6(master) runs for 10 min without error. After 10 min it gave a u4 error and the unit stopped. When I clear the error in the remote control it will start again. Sometimes slave one inverter compressor starts. But, only one fan starts running for 10 seconds, stops, and again starts after 30 seconds and stops within 10 seconds. slave condenser coil gets high heat. slave gas flow gives more sound. slave 2 is dead silent. total 40 indoor units. when I load more than 10 units it will give a u4 error. Please suggest an idea to rectify it.
Hi Mr Bon ,like to check with you .What does the acceptable range of ohms reading of the thermistor when ambient at 30°c?
@BonMj
2 жыл бұрын
Daikin 16K ohm for gas pipe thermistor
You have video setting of normal to emergency mode for inveter for singer unit. Thank you.
@BonMj
Жыл бұрын
Same setting
Who error of outdoor control pcb faulty
Hola será q me pueden ayudar no consigo la configuración de los ds de la placa a1p. Vrv4 RXYMQ8AY1. NO VINO con el papel y no los consigo
@BonMj
Ай бұрын
Your email?
Sir please provide us to pdf & image of how toh rest pcb and all sitting
Can you help me for PJ error vrv3 but install of sub parts accu Fan pcb 2 pcs. For master and 2 pcs. For Slave.. I also replace accu main pcb with correct dip switch settings
@BonMj
2 жыл бұрын
Check inverter and fan driver Any wire connections wrong. PJ is improper combination between inverter and fan driver
Sir Bon i just notice that red to black is 96 ohms red to white is 5 mega ohms what about white to black? is there a resistance reading fo that?
@BonMj
2 жыл бұрын
Red Black = 96K ohm Red white = 5M ohm Normally white and black i never measure, next time i get the reading in the video too.
@johnnyroxannebautista2063
2 жыл бұрын
@@BonMj thanks sir Bon.
Sir we changed ah bord from ah single deep switch to a new board double deep switch sir can't you please help me how to install this.sir this is the model RXMQ8AYL VRV4
@BonMj
2 жыл бұрын
I need to check. I only got RXYQ, RXQ, RZYQ, RZUR, RXUQ,
Hi Bon, how do you recognise how much the reading of thermistor or sensor should be, tq
@BonMj
2 жыл бұрын
16K ohm(temperature sround 30°c?)
@Mj-iu6yx
2 жыл бұрын
@@BonMj one more thing, where can I get the vrv combination, what is the resources, thank you.
@BonMj
2 жыл бұрын
@@Mj-iu6yx from manufacture
@Mj-iu6yx
2 жыл бұрын
@@BonMj hi Mr Bon, I need to do troubleshooting on cassette, the problem is, after working for 2 hours, the aircon causes to NCB trip, what do you think the problem is, please help me on this, thank you so much.
@BonMj
2 жыл бұрын
@@Mj-iu6yx check compressor ampere. May be over current or wire poor contact,also can be MCB got problem
Merhaba Daikin Vrv 4 error L1_U3 veriyor Problemi nasıl çözülür
@BonMj
Жыл бұрын
Check inverter pcb,fan motor, compressor
Sand pdf sir vrv3 mode satting
Sir how to set double deep switch to ah new board?
@BonMj
2 жыл бұрын
Follow the list. This list inside new pcb box
@noelreyes2771
2 жыл бұрын
@@BonMj sir there's no list inside the box only pcv sir if it's ok too you can't I get your email.add so that I can't sent it on your messenger
@BonMj
2 жыл бұрын
@@noelreyes2771 bonmj81@gmail.com
Sir bon can i apply in your company im filipino
Sir Daikin vrv3 salev1 on but master unit not working salev on continue but master not on sir rigen on errors no problem but master unit not start
@BonMj
2 жыл бұрын
Why master not working? Error?
thans sir do you have any group
@BonMj
Жыл бұрын
FB
Sir bon how are you
@BonMj
Жыл бұрын
I m good.Thanks bro
Hi brother
@BonMj
2 жыл бұрын
✌