Josh is a very good instructor. Clear, concise, shows things up close and stays right on subject. Not a lot of hemming and hawing during the instruction. Now I know what I need to get my pressure washer sparking. 👍

Great video. No nonsense. No blabbing. Straight to the point. Love it. Thanks.

Finally, a video that explains a coil test in detail and with no Bs. Thanks a million.

Excellent video. Straight to the point. No stupid gimmicks or daft music. No drama just getting on with what you need to do. A refreshig change!

So much better of a diagnostics video than even the ones by briggs. This was worth a like and subscribe.

Excellent video, clear voice, no waste of time and the detail in the instructions is extremely helpful. Thanks.

WOW! Hands down best freak'n no-nonsense no spark diagnosis and fix I've found. No need to look further!

The clearest and most precise explanation for this ignition problem that I have seen here, thank you.

Excellent video Josh! Your videos have helped me more than once. Thanks 🙏

Thank you for making such a great, informative video! Based on your video I was able to diagnose and repair my father's mower. Same issue as here... bad ignition coil. Followed your instructions to the letter and it runs perfectly now.

Excellent presentation perfectly done... no crazy music... thank you for the video right to the point

Excellent video. Very clear and understandable. You have saved me a lot of time and some money. I just had a bad ground wire.

This video earned you a subscriber. Very detailed and knowledgeable troubleshooting tips. Most of the internet is filled with "cleaned the carburetor" or "change the oil". This is the first bit of advice I've seen that goes into the issues surrounding the ignition coil, ground wire and flywheel. Hoping this will fix the issue with my mower. I have a spark plug tester coming in tomorrow. Thanks for the video and most importantly, the knowledge you shared with us!

Your method works if you have a spare coil. You can test the existing coil with an ohm meter. Connect one lead to the inside of the spark plug boot making sure you contact the metal inside. Connect the other probe to the engine block. The resistance should be around 3-4 K ohms. THis test can be done without removing the coil.

@philliphall5198

Жыл бұрын

Have you tested a Honda 4 terminal coil ? Trying to figure it out

@justtinkering6713

9 ай бұрын

Ohmmeter test doesn't work on my coil. I have two cylinder and one side works the other side doesn't, so I assume one coil is good. They both fail the ohmmeter test, even the good one. Swapped polarity, same thing.

These videos are good in case something goes wrong, when you type in YT search, you get helpful videos like this. 👍

Thanks Josh for your very helpful video. The spark plug tester you used takes all of the guess work out. With or without the orange spark light you know without a doubt if the ignition coil is working. Thanks again. Jerry.

Thanks for the vid. Starting new side hustle with first trial. Cleaned old carb, nothing, put new carb, spark and filter, nothing, now I’m informed of an essential part, the coil. Can’t wait to test it now.

Great video very clear and right to the point. Thanks again just replaced my coil.

Thanks for this great video - I watched it once, quickly got my new coil installed and gapped, then the mower started on the first pull.

Very thorough video I have an older walk behind Weedtrimmer & it has the same coil&flywheel set up thank you!

Thank you. After watching several videos I finally found the one that helped me solve my problem in language that I could understand!

Fantastic video - So well explained and easy to follow

Clear. Very well explained and to the point. Thumbs up !!!

Okay ....Soooo this is EXACTLY why there's small engine repair Pros . You knew everything you were talking about. Right down to the PO obvious experience you have, with the business card and the magnet sucking the coil on to it . bravo sir

Great channel! So easy to listen to and comprehend.

This is an AWESOME video. I've been slowly increasing my knowledge on repairing 2 and 4 cycle engines. When simple steps lead to improvements like illustrated here, there's an instant learning curve. Well presented. Straight to the point. Well done .

I would like to thank you for the test instrument info to connect to the coil. I’m heading to O’Reillys parts store. Thanks again, I wish more would share there sources, on videos.

My field of expertise is HVACR, and this video solved my problem... almost replaced an ignition coil and I had a bad ground due to braking system... Thanks!!

I appreciate how you demonstrated on how to diagnose now back to my garden tillet

I needed this vid…hopefully this will help me diagnose why my mower has no spark…thanks!

VERY GOOD DEMOSTRATION ,. THANK.YOU JOSH !!! THIS VIDEO WILL HELP ALOT OF PEOPLE WITH THIS PROBLEM !!!!!

Excellent, very good instructions. Thanks for sharing your knowledge!

Thank You Josh, mine was a dirty contact, I have sparky back now. Great video!

Great job man,... You ought to do more videos, You explain that very well

Best No BS video I've seen. Thanks !

Thnx Dude. Very in-depth & easy to follow.

Great explanation of exactly what happens with the coil connectors and wires connected or not for definitive diagnosis.

This is an excellent video! Thank you for making it!

Excellent Video presentation Dr. Phil

Excellent instructions and easy to understand, thank you for the video.

Awesome, Much appreciated from Lismore NSW Australia

Must agree Josh that this is an excellent video. Have a JX 75 John Deere 20 years old walk behind in Australia. spent over $500 doing it back up because they are so good but suspect the coil is stuffed. will now test but the coils are over $200 in Ozz. Thanks for this.

Now that was a concise, to the point video! Thanks!

Very well done video. Much appreciated!

Good job. Exactly what I needed to see. Thank You

Thank you for posting this. Helped me out tremendously.

thanks for solving my problem, very good instructions. thumbs up!

Thanks! You made my day! Your video helped me to find a problem in the switch from the handle ("Dead mans hand" in Swedish) that gave a flickering ground signal to the coil (Random ignition was my problem but now itis solved!)

VERY, VERY well explained video. Thank you.

Real world school....Excellent video!

Good video. Learnt a few good tricks there. Thanks.

Excellent video. Thanks for posting.

Great info here &Thank you for having No annoying back ground music

Solved my issue i removed the ignition coil and forgot to set the gap. Thank you for your great video

Easy and quick to understand. Thanks

Excellent video and great instructions.

Another great video. Thanks.

Thx , new subscriber, I am fixing the exact mower right now. I’ve had it running twice before . Not sure if her kids sabotage her mower and say it doesn’t work so they don’t have to cut the grass . We are going to follow your lead on this and tell her to never let any of her kids touch it ever again. The woodruff key was broken off this time . W t heck. He must drive it down the concrete stairs hahaha

The only thing you didn't mention is if like you are located near salty air, a build up of rust can form on both the magnets and the coil contact face.

Chingon mil gracias por el apoyo, saludos desde Michoacán Mex

Great video, saved me a bunch of money.

Thanks! Your videos are very very good!

Thanks for your video, I learned a lot.

great video and well explained

Thank you very much! I fixed my B&S!

Great video! I suspect my coil is the culprit. I check him out thanks to your video! Tom

That is the best explanation l ever heard. Great Job! You made me a subscriber! Thanks

Simple and accurate on the subject matter, Thnk you.

Good concise and to the point. Thanks

Before installing a new coil, always check the gap first. I just had one where the coil had vibrated and was touching the flywheel. Re-gaped and was fine.

@kevinw693

2 ай бұрын

Hell yea...check the gap...when the fly wheels vibrating and I've regaped her... ill roll over an go to sleep

Thanks a lot, Josh this vid saved a lot of shop money today, took your advice and walla my pressure washer is up and running again thanks a lot, Merry Christmas and a happy new year to you and yours

Thanx, big help on my cub cadet.

Good job Josh.

Awesome video! Thank you so much!

Thanks man for the information and video.

Good stuff! Thanks Josh!

Very pro video. Trying to get a BnS 1150 going for my shredder mulcher.

Awesome video I enjoyed the information on it, thxs.

You helped me fix the problem! Tenx

Wow good video learn something today great job bro. Thanks

Nice. Great idea to use a drill to turn the engine.

Well done video, thanks.

Great video.very helpful.

You could also not have spark due to corrosion between the coil and the mower frame.

Good presentation.

Thanks! Super helpful!

Very good info and video. I have collected 3 newer lawnmowers and have them in my barn; none have any spark. I am wondering why coil failure with these small engines is so common? But, in seeing this video, maybe it isn't the coil, but I'll bet it is. Thanks again.

Oh my gosh that is what I'll standing video I have never did any small engine or any Motors at all I've been a truck driver for 46 years I have a F525 John Deere and I can never get a spark hire so lost without my baby deer thank you

great teacher

Very good video !!

Nice video. I went through all of the steps and still had no spark. Finally found the problem. The cable from the starter cable was too long. It wasn't disengaging the kill switch where the grounding cable connects to. Once I shortened the cable (search on "How to Adjust Lawnmower Cable" on KZread), the lawnmower started on first pull.

Great job! Thanks

I'm about to test my ignition system on my craftsman push mower thank you for this video. I was mowing a clients lawn and I shut off my mower to move debris and it wouldn't start up again. Tested spark plug no spark tried another plug and still nothing so ima be heading to get that ignition coil tool and see if it's the coil.

Thanks for the video.

Hells fire got that / an thank you straight to the point ⭐⭐⭐⭐⭐👍

Great video.

Nice explanation

Great job.

Cheers, no bullshit. great vid, thanks.

thanks. this will help me