LIKE,SHARE and Subscribe To The channel for more videos like this one.. JAY HIND,VANDE MATARAM.🇮🇳🇮🇳
Жүктеу.....
Пікірлер: 50
@StablestLeaf3 ай бұрын
Very nice pulling old micro usb with piler without worrying about poor little contact of pcb
@sarvagnaraval5529
3 ай бұрын
Yes when you are confident in your skills😂✌️
@Junji1012 жыл бұрын
CC1 & CC2 need to be connected to GND with 5.1K Resistor for usb-c to usb-c charging.
@socke4306
Жыл бұрын
do you know what resistors i need for output? want to replace usb a output with usb c
@Junji101
Жыл бұрын
@@socke4306 I don't think it's possible to replace for output that way because you would need a chip to do the communicating for power
@socke4306
Жыл бұрын
@@Junji101 Its possible, i already have the answer from reddit. you just have to solder a 56k Resistor to allow 0,5A - 22k for 1,5A and 10k for 3A between on of the CC Lines and V. I tried it with 56k and it works perfect.
@Junji101
Жыл бұрын
@@socke4306 Oh cool. Thanks for letting me know. I had a misconception that it was more complex than that. Learn something new everyday.👍
@pavelwottena17484 ай бұрын
мне сегодня идея пришла а почему бы не поменять на type-c начал искать и наткнулся на вас,мне нравится идея,супер!!!!💪👍
@sarvagnaraval5529
4 ай бұрын
Glad you think so...😄 Btw don't forget to subscribe 😄
@nokiaphone54933 жыл бұрын
Very satisfying video.
@ayushmansarangi826011 ай бұрын
Bro we have to connect last two pin of bath side?
@mbk1251 Жыл бұрын
Which two pins carry data on the back of usb-c port? I have the lenovo yoga book YB1-X90F Which comes a older type USB Micro used both charging it and data transfer apart from mini HDMI port & 3.5m headphone jack it need the update hack used in your video but I do identifie data connection too Thanks
@chriscool7299
Жыл бұрын
where you able to mod your book. I am watching this video hoping to do the same with mine as well.
@scotty562 Жыл бұрын
This person should have connected two pairs of + and - so the usb c could be plugged in either way. The way this video was done could not have worked. The two pins on the end are - and + is the 4th pin in from each side. The way this was wired on the video would have caused a direct short circuit whenever something was plugged in. Hopefully it wasn't important because it's probably broken now.
@sgnoogle Жыл бұрын
As I can see, you have only 2 pin on the circuit board. If I have the classic 5 pin, which ones I need to solder to the 2 cables
@sarvagnaraval5529
Жыл бұрын
It's So Simple.....First u need to find + and - pin with multimeter.. and when you find it just solder wires with it and it will done 👍
@gypsyofcruzz200 Жыл бұрын
Hi sir. In the board, how to know which one is positive and negative ? This one have two terminals but mine have 5 of them.
@sarvagnaraval5529
11 ай бұрын
Can you text me the timeline? ... Which you want to say ..
@aijazorakzai1396 Жыл бұрын
Very nice
@sarvagnaraval5529
Жыл бұрын
Thanks ( dhanyawad )🙏
@aijazorakzai1396
Жыл бұрын
@@sarvagnaraval5529 MP
@luckywetland4 ай бұрын
Nice How can you identify the + and - on the board itself?
@sarvagnaraval5529
4 ай бұрын
I used multimeter to identify it. Btw don't forget to subscribe 😄
@luckywetland
4 ай бұрын
@@sarvagnaraval5529 Yes I understand haha... I mean, it would be great if you start videos on teaching beginners how to user the multimeter and how to understand the PCB
@Numbers-n-Innovations Жыл бұрын
Nice video, Bro can you please tell me I want to change y Romoss 25000 sense 9 power bank port from micro to type C, is it safe? Will it works as it is lie now? Just to place type c with micro and thats it?
@sarvagnaraval5529
Жыл бұрын
Yes 100%
@sarvagnaraval5529
Жыл бұрын
My friend is using this now.... You can trust...do all connections as shown in video
@user-xe2qv7pv2l3 жыл бұрын
nice work!!
@user-bf1kt3zf9l Жыл бұрын
Quality content 🔥🔥🔥
@thakurranjeet0203 жыл бұрын
Working or not?
@sarvagnaraval5529
2 жыл бұрын
Yes bro 100%
@thakurranjeet020
2 жыл бұрын
I will also try it
@sarvagnaraval5529
2 жыл бұрын
@@thakurranjeet020 wow 😁😁 good luck
@MdAsif-gp9ry2 жыл бұрын
bhai kya ham aisa kisi smartphone main kar sakte hai bataoge please.......................
@sarvagnaraval5529
2 жыл бұрын
Dekho bro.. maine yeh banaya to thha lekin ise Phone mai karna thoda mushkil hai.. kyoki I am not a professional . 😉😉 But in future I will try it .... Please support my channel to complete 1000subscribers I will try this in this month so stay tuned👌👌🤞🤞😀🙏🙏🙏
@sarvagnaraval5529
2 жыл бұрын
Thanks for your suggestions 😃🙏🙏
@MdAsif-gp9ry
2 жыл бұрын
@@sarvagnaraval5529 you're most welcome ! And thanks for reply my comment. aur bro mai pahle se aapka subscriber hoon.
@sarvagnaraval5529
2 жыл бұрын
@@MdAsif-gp9ry THANK YOU SO SO SO SO MUCH FOR YOUR SUPPORT 🙏🙏😁🤩🤩🤩❤️❤️
@sarvagnaraval5529
2 жыл бұрын
@@MdAsif-gp9ry sorry for late reply 😞😁
@lord-of-the-planet2 жыл бұрын
Can you change my phones port to type c
@sarvagnaraval5529
Жыл бұрын
Yes , but it's not my buisness 😂
@fakhriannabi3441 Жыл бұрын
it should not work, you need to add resistors
@sarvagnaraval5529
Жыл бұрын
Hey , i just connect two wires with main usb port which is output port so we don't need to add resistors .... Also I Have An Electronic Engineer at my home 😉
@itemsofmc3872
Жыл бұрын
@@sarvagnaraval5529 emberrassing for him not to tell you how to do it properly and then posting not working shit to youtube and acting like you did great
@debentertainment78609 ай бұрын
Micro usb connector jaise ukhada🥲
@adamspits5067 Жыл бұрын
Why are you wearing gloves
@sarvagnaraval5529
Жыл бұрын
Why are you eat with folk instead of hand? Lol just kidding... I wear gloves to make my video more professional... 🙂 Hope you like my video please subscribe bro ... Namaste 🙏
Пікірлер: 50
Very nice pulling old micro usb with piler without worrying about poor little contact of pcb
@sarvagnaraval5529
3 ай бұрын
Yes when you are confident in your skills😂✌️
CC1 & CC2 need to be connected to GND with 5.1K Resistor for usb-c to usb-c charging.
@socke4306
Жыл бұрын
do you know what resistors i need for output? want to replace usb a output with usb c
@Junji101
Жыл бұрын
@@socke4306 I don't think it's possible to replace for output that way because you would need a chip to do the communicating for power
@socke4306
Жыл бұрын
@@Junji101 Its possible, i already have the answer from reddit. you just have to solder a 56k Resistor to allow 0,5A - 22k for 1,5A and 10k for 3A between on of the CC Lines and V. I tried it with 56k and it works perfect.
@Junji101
Жыл бұрын
@@socke4306 Oh cool. Thanks for letting me know. I had a misconception that it was more complex than that. Learn something new everyday.👍
мне сегодня идея пришла а почему бы не поменять на type-c начал искать и наткнулся на вас,мне нравится идея,супер!!!!💪👍
@sarvagnaraval5529
4 ай бұрын
Glad you think so...😄 Btw don't forget to subscribe 😄
Very satisfying video.
Bro we have to connect last two pin of bath side?
Which two pins carry data on the back of usb-c port? I have the lenovo yoga book YB1-X90F Which comes a older type USB Micro used both charging it and data transfer apart from mini HDMI port & 3.5m headphone jack it need the update hack used in your video but I do identifie data connection too Thanks
@chriscool7299
Жыл бұрын
where you able to mod your book. I am watching this video hoping to do the same with mine as well.
This person should have connected two pairs of + and - so the usb c could be plugged in either way. The way this video was done could not have worked. The two pins on the end are - and + is the 4th pin in from each side. The way this was wired on the video would have caused a direct short circuit whenever something was plugged in. Hopefully it wasn't important because it's probably broken now.
As I can see, you have only 2 pin on the circuit board. If I have the classic 5 pin, which ones I need to solder to the 2 cables
@sarvagnaraval5529
Жыл бұрын
It's So Simple.....First u need to find + and - pin with multimeter.. and when you find it just solder wires with it and it will done 👍
Hi sir. In the board, how to know which one is positive and negative ? This one have two terminals but mine have 5 of them.
@sarvagnaraval5529
11 ай бұрын
Can you text me the timeline? ... Which you want to say ..
Very nice
@sarvagnaraval5529
Жыл бұрын
Thanks ( dhanyawad )🙏
@aijazorakzai1396
Жыл бұрын
@@sarvagnaraval5529 MP
Nice How can you identify the + and - on the board itself?
@sarvagnaraval5529
4 ай бұрын
I used multimeter to identify it. Btw don't forget to subscribe 😄
@luckywetland
4 ай бұрын
@@sarvagnaraval5529 Yes I understand haha... I mean, it would be great if you start videos on teaching beginners how to user the multimeter and how to understand the PCB
Nice video, Bro can you please tell me I want to change y Romoss 25000 sense 9 power bank port from micro to type C, is it safe? Will it works as it is lie now? Just to place type c with micro and thats it?
@sarvagnaraval5529
Жыл бұрын
Yes 100%
@sarvagnaraval5529
Жыл бұрын
My friend is using this now.... You can trust...do all connections as shown in video
nice work!!
Quality content 🔥🔥🔥
Working or not?
@sarvagnaraval5529
2 жыл бұрын
Yes bro 100%
@thakurranjeet020
2 жыл бұрын
I will also try it
@sarvagnaraval5529
2 жыл бұрын
@@thakurranjeet020 wow 😁😁 good luck
bhai kya ham aisa kisi smartphone main kar sakte hai bataoge please.......................
@sarvagnaraval5529
2 жыл бұрын
Dekho bro.. maine yeh banaya to thha lekin ise Phone mai karna thoda mushkil hai.. kyoki I am not a professional . 😉😉 But in future I will try it .... Please support my channel to complete 1000subscribers I will try this in this month so stay tuned👌👌🤞🤞😀🙏🙏🙏
@sarvagnaraval5529
2 жыл бұрын
Thanks for your suggestions 😃🙏🙏
@MdAsif-gp9ry
2 жыл бұрын
@@sarvagnaraval5529 you're most welcome ! And thanks for reply my comment. aur bro mai pahle se aapka subscriber hoon.
@sarvagnaraval5529
2 жыл бұрын
@@MdAsif-gp9ry THANK YOU SO SO SO SO MUCH FOR YOUR SUPPORT 🙏🙏😁🤩🤩🤩❤️❤️
@sarvagnaraval5529
2 жыл бұрын
@@MdAsif-gp9ry sorry for late reply 😞😁
Can you change my phones port to type c
@sarvagnaraval5529
Жыл бұрын
Yes , but it's not my buisness 😂
it should not work, you need to add resistors
@sarvagnaraval5529
Жыл бұрын
Hey , i just connect two wires with main usb port which is output port so we don't need to add resistors .... Also I Have An Electronic Engineer at my home 😉
@itemsofmc3872
Жыл бұрын
@@sarvagnaraval5529 emberrassing for him not to tell you how to do it properly and then posting not working shit to youtube and acting like you did great
Micro usb connector jaise ukhada🥲
Why are you wearing gloves
@sarvagnaraval5529
Жыл бұрын
Why are you eat with folk instead of hand? Lol just kidding... I wear gloves to make my video more professional... 🙂 Hope you like my video please subscribe bro ... Namaste 🙏