In a humid climate compressing duct insulation will make it sweat. Panduits can only be used on inner liner and the outer liner cannot be crushed or touching other ducts. This method might work in the northern zones but in Florida, the Mech cons

Great video , there are a lot of ways to do this . I like to tape the inner liner first making sure that the tape is making contact with both the inner liner and the metal equally, then I put a strap around it , next I pull up the outer and insulation. I make what looks like a suction cup by folding the inner liner inside the insulation so no insulation is exposed , the put the last strap . It won’t ever leak and looks good .

This is why some people have mold problems from people who don’t know how to correctly fit hvac equipment

Thank you for this clear and concise instructional video.

We put mastic at the collars first Then we tie and then tape and seal with mastic again

@ronherkey148

Жыл бұрын

Thank you for setting that straight

Thank you. Great directions!!!

Any different method when connecting flex to an adjustable elbow? There is no neck ridge to protect the panduit (zip) to fall off the elbow.

ok so silly question: why do you need the panduit gun? Can I just use nylon zip ties and then just hand tighten them? Thanks

I have high static pressure on a new 3.5 ton heat pump. I know for sure the flex duct is the issue. I have two 12" coming out of the supply in opposite directions. I know I need an 18" for a 3.5 ton heat pump. I did a diagram layout of the duct in the attic. What would happen if I just replace the two 12" to 18"? Ignoring the downstairs, because everything is between the walls. The problem was even worse with an undersized return. The original and only return was a 24x18. The total static pressure on the unit was .9 W.C. I was able to drop the TESP to .66 by making the return 30x24. Since there is so much static pressure and the unit TESP is a .2 and I need an 18" for a 3.5 ton for 1400 CFM. How big does the supply plenum should be and what shape? Should the supply plenum split to 3 18" going out to each of the 3 distribution boxes? Do the other three distribution boxes also need to be larger? Looking at the triangle shaped supply plenum I have very little room up for a rectangle plenum. I think a 3 feet ductboard supply plenum should work. There is a foot from the Air handler to the ceiling and I think 2 feet from the attic floor to the roof. Now I am looking at two types of designs. Design #1 keeps the 18" ducts straight by having a single 18" coming out of the supply and then a distribution box splitting it to three 18". The sides would be coming out straight to the to side boxes and one going to the third box with a slight curve. Design #2 splits to three right at the supply plenum and goes to each box individually, but all three will have a slight curve. I will not be using any metal plenums..... it will be all flex duct and ductboard boxes, because of budget. I am not trying to make a perfect system, but trying to remove the restriction from the 12" undersized ducts installed and replacing the flex duct that was patched with mastic with new ones. Another question about the installation..... I have the flex duct running up and strapped to the roof for support. Since the supply plenum is low to the floor due to the roof..... Can the flex duct be run on the attic floor? Can you tell me which layout makes more sense and less restrictive? Thank you. Layouts: Current i.ibb.co/Ld9kmPM/Flex-Duct-Layout-and-Size.jpg Option #1 i.ibb.co/GHyS00g/2022-07-05-0002.jpg Option #2 i.ibb.co/PNN8mSB/2022-07-05-0001.jpg Air Handler Specs ibb.co/17VvF4B Video of attic kzread.info/dash/bejne/m32iq7BxadSed7g.html

Thanks a lot !!!

Appreciate the instructions on how to build the ducts, but you didn't mention Mastic Sealant to make them air tight.

Bringing a handheld mirror would help to know if the other side of the duct looks good.

What size is the inlet on the register and the size of the flex duct?

So am 8 inch flex duct would connect to an 8 inche duct register?

Good

I have a register I am removing as we removed the wall it was connected to, how do I plug the existing duct work? Not really any need to cut it all off, but I want to just plug the flex duct.

@vinnymac8127

6 жыл бұрын

You shouldn't just plug the flex duct it's definitely not the right way to do it. Remove the entire piece of flex duct and the collar that's in the trunk duct. Cut a piece of sheetmetal that's at least two inches bigger than the hole each direction and screw it over the hole in the duct with sheetmetal screws. For example, if you have a 6" round hole in the duct, just cut your metal 8" by 8" so it overlaps an inch each direction and screw it. Then seal it completely with mastic and put a piece of insulation over it so it doesn't sweat. Tape the insulation on good and you're done.

@yauck1

6 жыл бұрын

Vinny Mac usually plenums have insulation inside so don’t forget to mend it too.

I have one vent in a room that I just know it’s not blowing properly all other vents in the house I can hear significantly air blowing but this one vent is not. I had a tech come out today because I felt some cold air leaking from where that vent connected to the air handler in the attic. They came out an put tape around it to seal it better but I’m still not satisfied. Now thinking that that duct may have a kink in it maybe where the strap is holding the duct to one of the beams in the attic. Could that cause less air flow and how would I check that. Should I drop the strap that’s holding that duct up?

@skydemon02

2 жыл бұрын

I have the same problem

Hello

Reading through the comments there are many many different ways to do this, I have been written up for not doing it the company way and have been berated for not doing it the Texan way. If you are a Sheetmetal worker check with your Forman to see the way the the company you are working for at the time does it. fair warning.

Butter the inside zip tie and zip tie the outside your done ✅

No mastic?

Inner liner, then tape it, then ziltie then pull putter down and tape that to the duct

What are the local inspectors insist you take first on the collar. He will fail it for sure if you don't.

Let's start by getting our terms right. The "inner liner" is called FLEX DUCT. All the material around the flex duct is the INSULATION. Next, you want to attach the flex duct to the boot, zip tie it so it doesn't pull off. Then apply mastic to seal the air in. You can substitute the mastic with HVAC tape if you can get a good seal around the boot, but the result generally is not as high performing. Pay attention here: DO NOT ZIP TIE THE INSULATION. All you're doing is crushing the insulation, destroying the R value, and a zip tie can't really grip insulation anyway. You can simply use aluminum HVAC tape to seal the insulation to the insulated part of the boot (register box). And you're done!

Good thing your ballcap is protected by your safety glasses!

Tape first then strap then insulation then strap again

Good video. BTW it's pronounced "duct" not "duck".

@jstriker623

6 жыл бұрын

Ken K Quack Quack. It's duck! Aflack!

LOOKS LIKE NO INSULATION WAS GRAB BY THE ZIP-TIE AT ALL

@joefleming3023

3 жыл бұрын

Yep. That part of the duct will sweat heavy in a humid attic or interstitial space.

@rickmcphee4206

3 жыл бұрын

Shoddy work

sorry but you are wrong if you zip tie out side of the flex you kill the r value not sure what state you are in but in the state of florida that will not fly

@hvacrookie6208

5 жыл бұрын

Agreed. I did this sort of work in FL for a little bit. You have to be careful with your insulation down there. I am not sure whether the box is internally lined, but that should be insulated, as well (at least for FL). You also need to be careful not to create kinks in the flex. It should be able to extend straight up from your box/diffuser and not be angled in the way the final product was in this video. I can tell he works hard and takes pride in his work, but I think those small details will make a difference on a large project.

@adamscan4u682

4 жыл бұрын

I was wondering this same thing. Plus I noticed it made the edge of the insulation flare out and away from the takeoff

@nym5635

2 жыл бұрын

Ive had to change my ducts every year because in the winter months there are buckets of water in my ducts what can I do to remedy that ? 25 ft of duct is 124 dollars and it's really annoying me now .. did the guys who installed it made a mistake somewhere , should I close my ceiling vents In the winter ?

@decliv

2 жыл бұрын

@@nym5635 the insulation need to be push all the way touching the collard or you will have condensation. Oohh and mastic of course.

@kendalgee5808

Жыл бұрын

@@nym5635 They say if you don't use mastic when installing the plastic duct onto the metal, it will sweat causing moisture, which eventually will saturated all of your insulation. So, brush a nickel thickness of mastic around the metal duct, then slide the plastic duct over it, this will create a waterproof seal and stop gaps for moisture to enter. Then clamp over it, then , pull up the insulation and foil, and foil tape it. Don't quote me, im not a pro. Just my .02 cents.

For sure this duck will condensate terrible connection

@tylerdirden3416

3 жыл бұрын

how so, what would you do better. i like perfection, explain pls.

@kameronharrison3397

3 жыл бұрын

I've been installing and service for over 20 years in Florida when you put that Panduit strap on the outside of that duct liner you are killing the insulation value that duck will condensate you should only silver tape and maybe some Mastic let me explain one more time by you putting a Panduit strap on the outside of the installation of that duck you are destroying the R-value right where that Panduit strap is at on the outside of that duck will condensate and fail inspection in Florida other than that pretty good video

@brandonluker4285

2 жыл бұрын

@@tylerdirden3416 compressed insulation no longer insulates. So you have to wrap the connection with more insulation or that part of your ducting will be cold and condensate like a cold drink does

@kirkey99

2 жыл бұрын

Hah! Joke's on you! This is actually a chicken!

It's not good way to put flexible. It's use aluminium tape only he didn't use clamp. It's a temporary way.thanks

@tmuxor

Жыл бұрын

He did use a zip tie strap at around 1:20

Why can’t we just zip tie it only?

To any viewers: if a flex duct tutorial doesn’t include mastic, they’re not doing it right and you should find another video

Terrible

Ya who cares if its not air tight…. 😂😂😂

What's the point of the tape over the panduit? What i normally do is put the liner of the flex halfway down the collar, tape it from the base of the collar so that both half the collar and flex liner are taped. Then panduit and tightent the half that's on the collar. Otherwise, what you did seems to only have been putting tape over the liner and panduit, having it attached to nothing but that.