How To Code Diesel Injector With Op-Com Vaux-Com Z19DT Z19DTH engine
#OpCom #VauxCom #Injectors In this video I demonstrate where you need to change code for injector if you replace them.
Жүктеу.....
Пікірлер: 39
@marinvremes57023 жыл бұрын
Hi there, thank you for sharing your knowledge. Very valuable. Once quastion I have. If I didn't mixed up the injectors, is it still necessary to do recording. I just started my Z19DTH after full engine repair, but the injectors are over fuelling ( I didn't replace the nozzles yet). Thanks
@--unknown--
3 жыл бұрын
Well they need to be coded. But over fuelling can cause bad injectors too not just the coding. Try to code them and then check them.
@LabinotBahtiri10 ай бұрын
I see the option RESET ECU, in what case you need to reset the ECU Thanks
@--unknown--
10 ай бұрын
As far as I know then if you replace ECU from different car then reset function is used
@LabinotBahtiri10 ай бұрын
Shoud we also code the switched Ignition Coil?
@--unknown--
10 ай бұрын
Not aware of that but I believe that yes they needs to be coded as they do the same function
@mohammedazam89154 жыл бұрын
Would the engine still run if injectors replaced but not coded?
@--unknown--
4 жыл бұрын
Sure it will working but not corectly. Without coding can misfire some injectors.
@hanibara7951
8 ай бұрын
I tried to put a second hand injectors on a z19dt without coding and couldn't start it
@mbz46522 жыл бұрын
If I buy a new injector, will this injector have it's own number? Every injector has it's own number right? All these number are registered in the ECU? What if I buy a non original injector Ridex for example and not Denso will it also have its number eventhough not being an original injector?
@--unknown--
2 жыл бұрын
Each injector have own serial number(code).
@hanibara7951
8 ай бұрын
Plus if you send the injector to repair or recalibrate they gonna regenerat a new code , so thee code on the injector will not help u
@ZeeshanAhmed-iw8sz3 жыл бұрын
Does petrol injectors needs programming
@--unknown--
3 жыл бұрын
Never tried on petrol cars
@ericsson52074 жыл бұрын
Can I somehow tune the car so it spraying more diesel to increase power? Answer please, Opel Astra Caravan 1.9 CDTI
@--unknown--
4 жыл бұрын
Not with the Op-com
@toolman953 ай бұрын
Where can i et the software please
@--unknown--
3 ай бұрын
Read the comments there must be somewhere the answer 😉
@mikemorley48432 жыл бұрын
Do you need the car key pass to do this
@--unknown--
2 жыл бұрын
All you need is turn on ignition
@mikemorley4843
2 жыл бұрын
@@--unknown-- thanks appreciate it
@--unknown--
2 жыл бұрын
@@mikemorley4843 you're welcome 👍
@a.l.e.x70543 жыл бұрын
Hi, please tell me the version of op com. Thank you
@--unknown--
3 жыл бұрын
In this video you can see the version. kzread.info/dash/bejne/iatrupqAda2pZZs.html
@MrIgriX4 жыл бұрын
please make video with DPF regeneration.
@--unknown--
4 жыл бұрын
My car have removed DPF that's why I'm not able to help with that. I can make video where you have to go in op-com to do that if you want.
@korayevcin1900 Жыл бұрын
hi. 1st injector coding fails. others are ok. what could be the reason?
@--unknown--
Жыл бұрын
Double check the code on injector. Or try that code add in different cylinder. If it works then could be wiring issue. If not then check the part number which is in my case is 159. Might be injector fitted from different car.
@korayevcin1900
Жыл бұрын
thanks. What should I do if it is installed from a different car?
@--unknown--
Жыл бұрын
@@korayevcin1900 if it's not made for your engine type then you won't be able to code it with Vaux-com. You will need to reprogram all fuel system including the fuel pump pressure and many other things you will need to replace to get it running properly. And anyway, then you will need all injectors with same code which in my case you can see on top of the injector code there is part number which ends with 159. Those last 3 digits must be the same for all injectors.
@korayevcin1900
Жыл бұрын
These last 3 digits are all the same. but 1st and 3rd injector coding cannot be done🤷🏼♂️
@--unknown--
Жыл бұрын
@@korayevcin1900 could be wiring problem. Quite common issue. What is those last 3 digits?
Пікірлер: 39
Hi there, thank you for sharing your knowledge. Very valuable. Once quastion I have. If I didn't mixed up the injectors, is it still necessary to do recording. I just started my Z19DTH after full engine repair, but the injectors are over fuelling ( I didn't replace the nozzles yet). Thanks
@--unknown--
3 жыл бұрын
Well they need to be coded. But over fuelling can cause bad injectors too not just the coding. Try to code them and then check them.
I see the option RESET ECU, in what case you need to reset the ECU Thanks
@--unknown--
10 ай бұрын
As far as I know then if you replace ECU from different car then reset function is used
Shoud we also code the switched Ignition Coil?
@--unknown--
10 ай бұрын
Not aware of that but I believe that yes they needs to be coded as they do the same function
Would the engine still run if injectors replaced but not coded?
@--unknown--
4 жыл бұрын
Sure it will working but not corectly. Without coding can misfire some injectors.
@hanibara7951
8 ай бұрын
I tried to put a second hand injectors on a z19dt without coding and couldn't start it
If I buy a new injector, will this injector have it's own number? Every injector has it's own number right? All these number are registered in the ECU? What if I buy a non original injector Ridex for example and not Denso will it also have its number eventhough not being an original injector?
@--unknown--
2 жыл бұрын
Each injector have own serial number(code).
@hanibara7951
8 ай бұрын
Plus if you send the injector to repair or recalibrate they gonna regenerat a new code , so thee code on the injector will not help u
Does petrol injectors needs programming
@--unknown--
3 жыл бұрын
Never tried on petrol cars
Can I somehow tune the car so it spraying more diesel to increase power? Answer please, Opel Astra Caravan 1.9 CDTI
@--unknown--
4 жыл бұрын
Not with the Op-com
Where can i et the software please
@--unknown--
3 ай бұрын
Read the comments there must be somewhere the answer 😉
Do you need the car key pass to do this
@--unknown--
2 жыл бұрын
All you need is turn on ignition
@mikemorley4843
2 жыл бұрын
@@--unknown-- thanks appreciate it
@--unknown--
2 жыл бұрын
@@mikemorley4843 you're welcome 👍
Hi, please tell me the version of op com. Thank you
@--unknown--
3 жыл бұрын
In this video you can see the version. kzread.info/dash/bejne/iatrupqAda2pZZs.html
please make video with DPF regeneration.
@--unknown--
4 жыл бұрын
My car have removed DPF that's why I'm not able to help with that. I can make video where you have to go in op-com to do that if you want.
hi. 1st injector coding fails. others are ok. what could be the reason?
@--unknown--
Жыл бұрын
Double check the code on injector. Or try that code add in different cylinder. If it works then could be wiring issue. If not then check the part number which is in my case is 159. Might be injector fitted from different car.
@korayevcin1900
Жыл бұрын
thanks. What should I do if it is installed from a different car?
@--unknown--
Жыл бұрын
@@korayevcin1900 if it's not made for your engine type then you won't be able to code it with Vaux-com. You will need to reprogram all fuel system including the fuel pump pressure and many other things you will need to replace to get it running properly. And anyway, then you will need all injectors with same code which in my case you can see on top of the injector code there is part number which ends with 159. Those last 3 digits must be the same for all injectors.
@korayevcin1900
Жыл бұрын
These last 3 digits are all the same. but 1st and 3rd injector coding cannot be done🤷🏼♂️
@--unknown--
Жыл бұрын
@@korayevcin1900 could be wiring problem. Quite common issue. What is those last 3 digits?
Is it OPCOM 2016?
@--unknown--
4 жыл бұрын
Not sure! I think 2012