I didn't know that only the signal and ground camera wires should be twisted, I always twisted them all. I guess we never really stop learning new things in this hobby, Thank you! Got allot of useful tips and information from this that I'm going to use on future builds :D

@headmazta

Жыл бұрын

Glad to give new info bro 💜

Love your Videos, man. My comment about your soldering: when you solder the wires into the XT60 you should definitely give it a bit more time to completely heat through and let the wire sink fully in, to make good and solid contact. It is not good to cover up everything with a couple of blobs of solder. Just give it heat, let it all melt and let the wire „swim“ into the pole. One other thing: when you tin your XT60 wires: don’t place them vertically on your workbench. The solder will flow down the wires due to gravity inside the insulation and stiffen up your wires. It may become hard to bend or put them in place later.

@DroneAcharya9

Жыл бұрын

I was literally going to say that.. Also, its better to always use the male/female counterpart of the XT60 plugged in so that the inner pins dont move

@headmazta

Жыл бұрын

Sorry, I skipped the footage because it looked so boring lol, but I'm not just covering the wire with tin. Although I'm moving the soldering iron left and right, I'm not pulling it away and still in contact with the lead so it's still heating the entire thing down to the pads. But yeah I forgot to mention it.

@Johow

Жыл бұрын

@@DroneAcharya9 also a good idea. But the bigger metal surface area(created by the extra set of female/male pins) pulls away a lot of heat. I made a little jig to hold the plug while soldering.

Awesome man , super clean the way your build Came out . Thanks for the video

As always, perfect video )

Great Build video

Really clean, I didn’t see a smokestopper though, unless I missed that :) Would definitely recommend to someone new to the hobby!

@headmazta

Жыл бұрын

Yes, absolutely. But honestly, a smoke stopper trips when you have too much current so you'll have to disconnect LEDs and VTX etc. when using it so I don't use it anymore. It's better to just triple check the diagrams and your wires, and make sure that there's not a single solder bridge between any pads.

Fantastic high quality tutorial and I picked to many useful tips! Thank you, Headmazta!

@headmazta

Жыл бұрын

Glad it was helpful!

Great video idea bro

Nice dude

Quality video with a lot of efforts ! Really clean and easy to understand ! I will probably come back to this one for my first build !

@headmazta

Жыл бұрын

Thanks so much bro!!

Thank you so much for making this video, I am learning to built the FPV

@headmazta

Жыл бұрын

Good luck!

Many thanks for sharing your build process! It can be very daunting for new FPV hobbyists. You made the procedure very straight-forward and clinical, as you do so well. 🙏❤ Those motors look very nice btw!

@headmazta

Жыл бұрын

Thanks a lot!

That was fantastic, thanks for the content my dude! Also fun to see your full setup. 🤌🏻🤌🏻🔥🔥🔥🔥

@headmazta

Жыл бұрын

Thanks brother! Please note that i'm using FalcoX for this build now :D

Superb work always brother for real. I love it !!🏆🏆🏆

@headmazta

Жыл бұрын

Much appreciated my bro!!

Nice clean build!

@headmazta

Жыл бұрын

Thanks bro!1

idol talaga to

Make sure to melt all of the solder on the lead at the same time. If you do it only parts at a time, then it will result in a cold solder joint, which is bad. Great build btw. Keep it up👍

Pristine parts from Tmotor, clean build indeed. I like it that all wires are cut to the exact length so they don't dangle. red wire not wrapped around is new to me and it totally makes sense to twist only the ground wire to the vtx video or tx/rx.

@headmazta

Жыл бұрын

Yes bro, learned twisting signal and ground wires from another video. It's that or use a coax cable.

DQUAD ALL DAY BAYBAY

@headmazta

Жыл бұрын

💜💜💜

You forgot to update blheli, super important

No Talking Quad Build (great build vid!)

@headmazta

Жыл бұрын

Ahaha yes bro. Wait how did you put that emoji?

@kelsey7k

Жыл бұрын

@@headmazta lol it's called (colon)elbowcough(colon), but we all know he's dabbing. what a time to be alive hahaha

master...😁😁😁

@headmazta

Жыл бұрын

Thanks brother!! 💜

Me desculpa fazer esta observação mas o fio branco da camera liga no Vbat e não no CC. Parabens pela montagem, ficou muito bom.

Nice. Acro trainer angle # 20 Function??

I would say you should use higher temps for shorter durations, rather than lower temps for longer periods.. So instead of 400, you probably should use 430 or 440 and that will give you better joints.. the trick is to be quick in and out..

Thanks.interesting . talk you laterb.uddy, 🤘

nice FC i have a few of those, i dont like the holes in the pads i messed up a verry good and new esc from dripping solder through that hole

@headmazta

Жыл бұрын

Yeah actually

Can you build the drone with HD unit (not analog) like DJI 03?

most fpv people say to twist all the wires though

man, it was very good, only one point that catches my attention is where the capacitor is. I wouldn't do that in my build. I would try to use something as a stand or solder directly to the lipo pad. Another point is the RX, it could have put a heat shrink and used a tpu support for it and the antenna. Other than that, your assembly was very good, congratulations

@headmazta

Жыл бұрын

Thanks bro! It was a tight build, can't put the cap there. And the RX, i'm done putting them in heat shrinks, hard to maintain.

nice build. I'm wondering why you didn't / don't put nuts on the top of the stack screws (after FC)? No problems with it coming off the stack from vibration or crashes? I'm also wondering why you recommend only using Raceband for VTX. Thanks

@headmazta

Жыл бұрын

Oh, FlightOne recommends to mount the FC without nylon screws on top so it's been. I don't know what Befaflight devs say about that but I have replaced my firmware with FalcoX anyway. It's been the standard, especially when you're flying with your friends, it's easier to choose a channel. Allows up to 8 persons to fly at the same time.

brooo... that frame... wowww

@headmazta

Жыл бұрын

Yes bro! Wait until the final version is out, it's gonna be awesome 💜💜💜

@AnugrahPrahasta

Жыл бұрын

@@headmazta alrighttt

still freestyling analog? I just moved to digital myself. we fly the same motors and stack I just run 2080kv.

@headmazta

Жыл бұрын

Yeah lol. Sometimes I fly my friends' digital cinewhoops.

Don’t see the point of soldering onto the speedy bee vtx as it has a very useful plug that you can solder to the fc and in case you need to change vtx because you burnt the previous one, it’s a lot easier. However, great video, very neat and useful for beginners.

@headmazta

Жыл бұрын

Thanks bro. Hmm highly unlikely to burn a VTX and it's very important to not have a loose connection after repeated crashing.

@baptiste_nonat

Жыл бұрын

@@headmazta understandable BUT I use speedy bee vtx and I crashed a month ago in a field, my antenna unscrewed a bit from the sma connector and my vtx burnt by being 25 min in the field while I was searching for it. Then the replacement was extremely easy as y just had to unplug the pigtail and the connector and the problem was solved. Both options are good !

Paps t motor f55 pro II 32 bit Tapos Wild Willy's Special Juice 2306 Motor V2 2700kv Tapos 1000uf 50v cap.. 6s pero maganda din siyang 4s..

Goodbye to FlightOne? Lol...i am also now using Betaflight

@headmazta

Жыл бұрын

Nope, bought a FalcoX license for this a few days after.

please include prices of the parts you get in your home country. if not interested in doing that, can you tell the total price.

What AWG size wire can use for capacitor ?

@headmazta

Жыл бұрын

Same as the motor wires :)

5:44 - does anyone know what the purpose of covering the up at he cooling fins is? To me it seems like that would be a bad thing. I’ve very new so spry if that is a dumb question.

@headmazta

Жыл бұрын

Just covering the gaps temporarily to avoid lead going into it.

simplest way to remove insulation from silicon wires - yiur nails.

@headmazta

Жыл бұрын

It's harder to achieve the desired length of the exposed wire accurately so I choose the knife :)

Wow. degree gorpro? Link TPU please!

@headmazta

Жыл бұрын

www.thingiverse.com/thing:3955278, 25 deg :)

Why your Feed Forward Jitter Reduction is set to 12 ? This in not in the Supafly preset.

@headmazta

Жыл бұрын

Maybe it's updated, not sure tho

This frame no longer exists, which one do you recommend?

@headmazta

Жыл бұрын

It's not yet out, actually. For now I would recommend the LRX

Saan na kakabili Ng mga parts Ng FPV?

@headmazta

11 ай бұрын

PinoyFPV :)

mm yummy kwad

@headmazta

Жыл бұрын

Thanks bro!

𝓟Ř𝔬𝓂𝔬𝐒ϻ 😥

bro make me a new drone please message me

@headmazta

Жыл бұрын

No prob master!!

@TeamBeasty2147

Жыл бұрын

@@headmazta bro alam mo pa number ko ?

@headmazta

Жыл бұрын

@@TeamBeasty2147 Ay hindi bro eh, nag pm ako sa fb at ig bro. Not sure if active yun 🤔