This is a brief video on how to clean your hair clippers and products
Жүктеу.....
Пікірлер: 25
@lampshadesoapmaker6788 жыл бұрын
You take the blade off the clippers and get sit in barbicide for 10 minutes as is instructed by barbicide
@mountopia774 жыл бұрын
Just unscrew the blade off and set it in for 10 min.
@charlesnicholson963510 жыл бұрын
We got the same setup! Good video.
@rjcutsandgrooms
10 жыл бұрын
Thanks 4 watching! I'm learning more and more it's a process def..
@tjsandrasaliu456210 жыл бұрын
YOU should NEVER blow your clipper from the mouth because you're adding even more bacteria from your saliva onto the clipper....lol Great Vid though!
@rjcutsandgrooms
10 жыл бұрын
Lol thanks man much appreciated!
@thebigmann81
4 жыл бұрын
Can of compressed air will be better.
@larrythebarberman7 жыл бұрын
good stuff
@thebigmann814 жыл бұрын
You mentioned clipper oil but didn't mention the clipper grease for the motor.
@GarrickWhite9 жыл бұрын
Never, never wash your blades in water base solutions. That's the best way to destroy your clippers and blades. You can take the blade off and clean it with barbercide, but you have to make sure you dry it properly to prevent discoloration and rust. Best to just use petroleum base blade wash to clean your blades with ,such as andis or oster wash. You can use other petroleum base solutions such as lighter fluid, break fluid and the likes. Using water base solutions not only destroy your clippers, but put you in danger of an electrical shock.
@randyyoshi67809 жыл бұрын
thank you
@dawnoakwood47466 жыл бұрын
do you dilute the barbicide with water before soaking the clippers? Or do you use it full strength?
@qprince5678 жыл бұрын
You suppose to let it sit for over 10 min. !
@reservoirfrog18 жыл бұрын
Is that un-diluted Barbicide? I've go taken but not sure how to dilute with water
@duty5k7 жыл бұрын
Looks like the guy from the matrix
@thebigmann814 жыл бұрын
I heard barbercide is only for the combs,guards and holders and not the blades. Is that true? I heard it rusts the blades.
@danielcombs3207
4 жыл бұрын
Don't use Barbicide like that guy demonstrated. Detach the blades, brush off any loose hair, I wipe my blades down with 99% isopropyl alcohol, the higher 91 % or 99 % has little water. Immerse the blades in a mixture of Barbicide for only 10 mins. I thoroughly dry using tissue and air dry using my hairdryer. Reattach the blades and oil them. I brush off loose hair between cuts and spray the blades and housing with a disenfectant clipper spray by Andis and oil the blades after 2or 3 haircuts. Mix 2oz. Barbicide concentrate to 1 gallon distilled water. Just don't leave anything in Barbicide for more then 10 mins. It will destroy your combs and brushes and your metal cutting tools will rust. That's just what I do, good luck.
@danielcombs3207
4 жыл бұрын
There is a Barbicide certification course you can download , after completing the test you can print up the certificate and display it in a frame. It's easy and free.
@danielcombs3207
4 жыл бұрын
Sorry Kenneth , 2 oz. Barbicide to 32oz in your jar is the correct mix. The timing is definitely 10 mins for immersion. Then rinse off and dry. Forget the other mixing directions that's for other disenfectants.
@LSade058710 жыл бұрын
Never never never put clippers in pure Barbicide. Your supposed to dilute the solution with water. Then run your clippers into the solution.
@LSade0587
10 жыл бұрын
Also when sanitizing them they should be in the solution for ten minutes to correctly sanitize.
@rjcutsandgrooms
10 жыл бұрын
Thanks for the advice man il keep that in mind!
@ksjohnson2199 жыл бұрын
that's not a cleaner that's a disinfectant solution you need blade wash by oster or andis blade care solution not the spray
@Pura_pesca9192 жыл бұрын
Man this video quality is bad it makes it retro bad ass lol cheers hope you doing well bro it’s been 8years since you posted this
@reservoirfrog18 жыл бұрын
Is that un-diluted Barbicide? I've go taken but not sure how to dilute with water
Пікірлер: 25
You take the blade off the clippers and get sit in barbicide for 10 minutes as is instructed by barbicide
Just unscrew the blade off and set it in for 10 min.
We got the same setup! Good video.
@rjcutsandgrooms
10 жыл бұрын
Thanks 4 watching! I'm learning more and more it's a process def..
YOU should NEVER blow your clipper from the mouth because you're adding even more bacteria from your saliva onto the clipper....lol Great Vid though!
@rjcutsandgrooms
10 жыл бұрын
Lol thanks man much appreciated!
@thebigmann81
4 жыл бұрын
Can of compressed air will be better.
good stuff
You mentioned clipper oil but didn't mention the clipper grease for the motor.
Never, never wash your blades in water base solutions. That's the best way to destroy your clippers and blades. You can take the blade off and clean it with barbercide, but you have to make sure you dry it properly to prevent discoloration and rust. Best to just use petroleum base blade wash to clean your blades with ,such as andis or oster wash. You can use other petroleum base solutions such as lighter fluid, break fluid and the likes. Using water base solutions not only destroy your clippers, but put you in danger of an electrical shock.
thank you
do you dilute the barbicide with water before soaking the clippers? Or do you use it full strength?
You suppose to let it sit for over 10 min. !
Is that un-diluted Barbicide? I've go taken but not sure how to dilute with water
Looks like the guy from the matrix
I heard barbercide is only for the combs,guards and holders and not the blades. Is that true? I heard it rusts the blades.
@danielcombs3207
4 жыл бұрын
Don't use Barbicide like that guy demonstrated. Detach the blades, brush off any loose hair, I wipe my blades down with 99% isopropyl alcohol, the higher 91 % or 99 % has little water. Immerse the blades in a mixture of Barbicide for only 10 mins. I thoroughly dry using tissue and air dry using my hairdryer. Reattach the blades and oil them. I brush off loose hair between cuts and spray the blades and housing with a disenfectant clipper spray by Andis and oil the blades after 2or 3 haircuts. Mix 2oz. Barbicide concentrate to 1 gallon distilled water. Just don't leave anything in Barbicide for more then 10 mins. It will destroy your combs and brushes and your metal cutting tools will rust. That's just what I do, good luck.
@danielcombs3207
4 жыл бұрын
There is a Barbicide certification course you can download , after completing the test you can print up the certificate and display it in a frame. It's easy and free.
@danielcombs3207
4 жыл бұрын
Sorry Kenneth , 2 oz. Barbicide to 32oz in your jar is the correct mix. The timing is definitely 10 mins for immersion. Then rinse off and dry. Forget the other mixing directions that's for other disenfectants.
Never never never put clippers in pure Barbicide. Your supposed to dilute the solution with water. Then run your clippers into the solution.
@LSade0587
10 жыл бұрын
Also when sanitizing them they should be in the solution for ten minutes to correctly sanitize.
@rjcutsandgrooms
10 жыл бұрын
Thanks for the advice man il keep that in mind!
that's not a cleaner that's a disinfectant solution you need blade wash by oster or andis blade care solution not the spray
Man this video quality is bad it makes it retro bad ass lol cheers hope you doing well bro it’s been 8years since you posted this
Is that un-diluted Barbicide? I've go taken but not sure how to dilute with water