A little fast for newbies there bro. When you pushed up on the shell stop to disassemble the bolt mechanism, it would have been nice to see a close up of you working in that area.

Ive had the same 870 i got 25 yrs ago, think ive taken it down once, still works good!😂

What hung me up was the bolt assembly. You did say anything about the two latches

@Avery9Hopson

3 жыл бұрын

Upvote this boys. Also on my 870 I have to engage one latch then push the bolt carrier in slightly then engage the second latch.

@Prophecynut

2 жыл бұрын

This is in the Brownell vid

Very helpful my father just passed down his 870 to me and it needed a little love.

@concertjunkie8592

11 ай бұрын

Same here

The barrel is very susceptible to corrosion so make sure it's well oiled when storing. Good video. I love my 870.

@scottfulghum8408

3 жыл бұрын

I’m getting my old 870 back from a friend who was storing it for me since 1990. The gun is a late 70’s vintage and hardly used. I’m hoping the barrel has survived.

@JS-te4gz

3 жыл бұрын

Isn't it chrome lined....?

@TishaHayes

3 жыл бұрын

I have an 870 that was in storage and the clip that was holding the barrel was lined with carpet. The carpet sucked up enough moisture from the air that it left a rust half moon on the barrel, only where the carpet had touched it. It hasn't pitted the barrel but to make it look normal I will need to strip and re-blue the barrel. That is very annoying; I have had that shotgun since 1980.

@anthonyakers6374

3 жыл бұрын

@@TishaHayes had the same problem mositure must have gotton on mine somehow. Went to the range stored it away for a week weeks when i went to pull it out to clean it had a bit of rust on it very annoying. You think theyd come with some sort of anodized or rust resistant finish. :(

New shotgun owner here. Didn’t know what a lifting arm is. Another video got me there though.

@spconrad9612

2 жыл бұрын

Yeah, he should have slowed down a little. If the video was 30 sec to a minute longer it would have been a little better.

Very helpful video, worth the watch if you're new to the Remington 870.

Love my Hoppe’s Bore Snake Viper for the 20 gauge 870.

You did a VERY poor job of explaining the hardest parts, i.e., how to pinch and remove and restore the bolt carrier.

@Avery9Hopson

3 жыл бұрын

Trueeee. The bolt carrier balancing you have to pull off is so damn annoying

Nice job. Thank you bud.

Very helpful, thanks.

@Hoppesguncare

4 жыл бұрын

Glad to hear it!

Pretty epic, thank you for the tutorial

@GODWITHUS0712

3 жыл бұрын

Your a nobe

devoled a bit od surface rust any way to get rid of it seemed to have stained the finish

This was very helpful. I just picked up an 870. Any tips on releasing a stuck safety system? I turned it to the locked position and now it doesn’t seem to want to unlock.

So many people never care for the magazine on their pump shotguns. It is so easy to remove the cover, spring and follower then stack a few patches on a cleaning jag and see how much grime is in the typical magazine. Face it, every shotshell passes through the receiver on its way to the mag tube, so the shells are bringing dirt in with them. as much oil as is applied and wiped off the barrel should go on the inside of the magazine when done cleaning. Then wipe off the spring and oil it as well. And clean the follower. If you have never done it, go ahead, see what I am saying.

Does yours not have a stop and spring?

Is the barrel the only part of the shotgun being cleaned with cleaner?

@aronkovacs1386

Жыл бұрын

With bore cleaner yes, it breaks down lead fouling. Not necessary for other parts.

I'm new to an 870. Do you need to take the trigger assembly out to clean every time you shoot it?

@pedrobrando4606

Жыл бұрын

Absolutely not.I will just spray the inside of the receiver with a airasol gun cleaner,then finish with a airasol gun oil and then compressed air.Store the gun with a thin coat of gun oil in a climate controlled space.You do not have to remove the barrel to clean it. Maybe every 1000 rounds or 10 years would I disassemble a 870 for cleaning.

@you7219

Жыл бұрын

@@pedrobrando4606 that was helpful thanks picking mine up in a few days 👍🏽

So can I use a copper Brillo pad and a rod and some WD-40? Instead of the 50$ kits?

@robertmilkshake1013

2 жыл бұрын

I've heard that WD-40 works great initially but ends up gumming up.

@spconrad9612

2 жыл бұрын

True, look up a video on using WD-40. As the other poster stated, it works good initially, but the residue not removed gums up and is not good long term.

@markwinkel9104

2 жыл бұрын

These cleaning kits are not $50 they are cheaper than that. Don’t be a cheapskate take care of your guns properly and they will last a very long time

If I haven't used this shotgun in a few years should I do a full clean like this before I were to use it again ?

@T44m45

3 жыл бұрын

If it has been a few years then yeah, you should give it a good clean. Removing old grease and oil makes it that much smoother.

Can you just clean it with WD40? thanks

@wolfsegovia

10 ай бұрын

WD40 has solvents in it. Once these evaporate, there is little oil left to protect the metal. Perhaps using just to clean and then adding a layer of oil.

You went too fast. First time cleaning. Can’t reassemble.

@DaRealArtist

2 жыл бұрын

I’ve had my 870 many years and only shot it a few times. It’s keep in a designated area. But I know it’s needs to be cleaned now. Kinda skeptical of resembling it?!!🤷🏾‍♂️

@Prophecynut

2 жыл бұрын

Brownell Video

Oh lifting arm I know what that is 🙄

Why can't an AR barrel come off that easy?? I'll never understand. SMH

You didn't show all the steps.

@pedrobrando4606

9 ай бұрын

There are more detailed videos on YT.This one serves as a refresher.A complete video would take about 15 minutes.