These VQ 37 engines are a real gem. I have one in my 2019 370Z and was able to get about 55 crankshaft peak hp more out of it with an intake, exhaust and dyno tune. I did run a mixture of race gas with the pump gas to bring up the octane level from 91 to 94. This enabled the tuner to advance the timing more and extract more power.

@TheAutoTeacher

5 ай бұрын

Nice!

Thank YOU dearly! Did the cleaning first, so hopeful this resolved it. My car runs and idles very smoothly now!

@TheAutoTeacher

Ай бұрын

You’re welcome!

You’re an amazing tutorial guy. I liked how you recorded and explained everything

@TheAutoTeacher

2 ай бұрын

Thank you! Glad it helped.

thank you man just got my g37 coupe first car ive tried working on myself i know it wasnt serious but this taught me something thank you

@TheAutoTeacher

6 ай бұрын

You’re welcome!

Perfect video! Perfect explanation and execution! Just earned a new subscriber!! THANK YOU

@TheAutoTeacher

2 ай бұрын

Thanks and welcome!

So helpful. Thank you!

@TheAutoTeacher

2 жыл бұрын

You’re welcome!

Worked, thanks man! To get the engine light off disconnect ur negative on the battery for 30 secs or more and should go away

@TheAutoTeacher

2 жыл бұрын

You’re welcome!

Thank you

@TheAutoTeacher

Жыл бұрын

You're welcome

Ty so much

@TheAutoTeacher

Жыл бұрын

You’re welcome!

Thanks for the video. Would you recommend OEM MAF or do 3rd parties work just as fine

@TheAutoTeacher

2 ай бұрын

Your welcome.OEM is always preferred, it really depends on the price difference. A aftermarket part bought from a reputable place will have a better/longer warranty.

I got the P0174,P0300 and C1109 codes. Is it just cleaning the mass airflow sensors ?

@TheAutoTeacher

6 ай бұрын

A malfunctioning mass airflow (MAF) sensor is one of the most common causes of P0174 code.

What tools did you use for this my G37 threw that same code

@TheAutoTeacher

Жыл бұрын

You can see all the tools we used in the video description!

Like is it good if buy the maf sensors at o’reillys I don’t want to the dealership to pay a 1000 for the sensors

@TheAutoTeacher

2 жыл бұрын

Yes, you could get one from any major auto parts retailer, but I would get one with a lifetime warranty.

I got the p0304 and p0300 and I already changed my spark plug you think I just have to clean the (MAF) ?

@TheAutoTeacher

2 ай бұрын

Since you replaced your spark plugs and still have a misfire on cylinder 4, I would install a new coil on 4 and that should take care of both your PO codes .

Did you have to perform the relearn procedure after?

@TheAutoTeacher

10 ай бұрын

We used the OBD2 scanner to clear the code .

Is there any like reprogramming that needs to take place after replacing the sensors?

@TheAutoTeacher

Ай бұрын

No

im having trouble pulling the wire off the sensor, not sure why it wont come out even if i push on the tab, it doesn’t budge

@TheAutoTeacher

Жыл бұрын

They become old and brittle and accumulate dirt as the miles pile on, in a warm area try WD-40 and pushing gently down on the tab and wiggle back-and-forth. If that doesn't work, get a small screwdriver or hook and come in from the front.Once released, you will have to use electrical cleaner to remove the WD 40 .

@adambeck8180

Жыл бұрын

On my 2006 FX35, you gently pry the tab UP. Then the plug comes right out.

My g35 will stop and go , like you would press on the gas and instantly press on the brakes , you know what could be the issue for that ?

@TheAutoTeacher

Жыл бұрын

Do you have any PO codes?

I did this and it works sweet. Problem is, its 2009 so i'm going to replace both

@TheAutoTeacher

2 жыл бұрын

Awesome!

@issas4660

2 жыл бұрын

Anyone know iff i have to buy 2 seperate left and right maf sensors or does that even matter and all maf sensors fit the same left and right? I own a 2015 q50 3.7

@davidsontchi6979

2 жыл бұрын

@@issas4660 If u get them from Infiniti, u pay $370, a piece. I got mine off Ebay for $49 for Both. Infiniti uses Hitachi MAF meters. Just put that & ur type of car & see what u'll find. Good luck

@atbmts6

Жыл бұрын

@@davidsontchi6979 ty for this

@davidsontchi6979

Жыл бұрын

@@atbmts6 TY for telling whats up

What size is that to remove it 8mm doesn’t fit and my screw was stripped by the previous owner

@TheAutoTeacher

Жыл бұрын

It should be at 8 mm ,try a small Phillips screwdriver and if all else fails use a small pair of channel locks.

Wait for these g37x 13, do both sensors have a metallic side and black side ?

@TheAutoTeacher

Жыл бұрын

yes

I replaced my maf sensor because I had the code for the sensor the p010B or something like that lol anyways I replaced the sensor & my car is no longer misfiring during driving but now it doesn't always start the first time I start it. I usually have to try a second time & it'll start. I did get the part from autozone, could that be why bc it's not an oem?

@TheAutoTeacher

4 ай бұрын

Getting the part from AutoZone shouldn't be an issue. Have you checked your air filter to make sure it's clean and when was the last time your spark plugs were replaced?

@gsteel98

23 күн бұрын

These cars are very sensitive regarding sensors. When I replaced my crankshaft sensor with doorman it worked for a few months then gave problems on and off til i put in a denso sensor. The original denso I put in after the original failure was broken by the flexplate so my mechanic swapped a doorman in I didn't choose it. Get denso, hitachi or ngk when it comes to sensors nothing else unless you do research. Z1 has been a tried and true site for aftermarket parts. Rockauto has oem MAF sensors as well I think 60 each

Did you disconnect the battery or is it not necessary?

@TheAutoTeacher

2 жыл бұрын

Not Necessary.

@davidsontchi6979

2 жыл бұрын

Not necessary to disconnect it

If I get a new sensor and put it on will my engine light go away if that's the only problem, the sensor? Or would I have to delete the code install the new one then see if it worked???

@TheAutoTeacher

Жыл бұрын

Sometimes it will go away once you start driving , but it's easier and faster to just delete the code.

@pablogarcia8188

Жыл бұрын

@@TheAutoTeacher thanks for the reply, what are some other things I can also do before spraying the sensor, like new filters ? Or such

@TheAutoTeacher

Жыл бұрын

Replace your filters replaced every 15,000 miles .

@pablogarcia8188

Жыл бұрын

@@TheAutoTeacher when you say it's easier and faster to delete the code do you mean by deleting it and putting the new sensor in to wait and see if the check engine light comes back ?

I have a P006A, P0101, P0172 should I just clean them or replace it?

@TheAutoTeacher

Ай бұрын

I would clean it first.

Im having trouble pulling out the swnsor it self i was able to disconnect the wires and took off the screws but its like the sensor stuck 😩

@TheAutoTeacher

10 ай бұрын

Not sure why that would be, if you remove the two screws usually it pulls out super easy. There's only a small rubber seal, and it's made of plastic so there wouldn't be any corrosion. Try using pliers if you're replacing it with a new one.

My g35x 2007 drives but at 3k rpm it stalls and acts like a rev limiter could this be the issue ?

@TheAutoTeacher

7 ай бұрын

Yes. Check your air cleaners for limited flow and then I would clean or replace your MAF sensor. Do you have any PO codes?

Does anyone know why my bank 1 sensor 1 o2 sensor is throwing a code after replacing it with a new one

@TheAutoTeacher

Жыл бұрын

It may take a couple miles before the ECM resets and shuts off the light, it's easier just to do it with a scan tool if accessible.

I have code p0102 and code p0300.. could dirty MAF sensors cause this ?

@TheAutoTeacher

7 ай бұрын

Yes, a PO102 could be a Faulty mass air flow sensor. PO102 - Intake air leaks - Dirty mass air flow sensor - Dirty mass air filter - Mass air flow sensor harness is open or shorted - Mass air flow sensor circuit poor electrical connection The PO 300 is multi misfire, which is probably caused by your P102 code. I would address the PO102 first.

What size screwdriver you used?

@TheAutoTeacher

Жыл бұрын

You can use an 8 mm socket or a small Phillips screwdriver .

@carlos889574

Жыл бұрын

@@TheAutoTeacher thank you

Aye quick question i have a code p0174 and was just wondering how do i find out which side needs to be replaced??

@StrictlyBusiness-de6kg

2 ай бұрын

Also i dropped that screw while messing with it can i replace it?? If so where should i look for one!?

@TheAutoTeacher

2 ай бұрын

P0174 indicates Bank 2 of the engine has a lean fuel mixture. Drivers side.

@TheAutoTeacher

2 ай бұрын

For the screw, you can take one from the other side and go directly to a hardware store or the dealer to make sure you get the proper screw.

I replaced coils and sparks but I’m getting a random misfire

@TheAutoTeacher

2 ай бұрын

Any PO codes ?

Hello I have a 2009 FX35 drives normal However in park the rpm needle goes up and down every 15 seconds or so slightly not by a lot. And when I rev it in park the rpm dips before coming back to normal. Any help? Thanks in advance.

@TheAutoTeacher

Жыл бұрын

It could be a lot of things, I would start with the cheapest things first and go from there. Check your air cleaners, check for any vacuum leaks, clean the mass airflow sensor and when was the last time spark plugs were installed, as you can see the list can go on and on.

@mostafajbeily4529

Жыл бұрын

6 brand new spark plugs. I was told coils can cause this but I don't think so. It runs fine. It only shivers a bit when stationary.

@mostafajbeily4529

Жыл бұрын

How do I check for vaccum leaks.

@TheAutoTeacher

Жыл бұрын

Check for any split or deteriorating hose's , or anything disconnected. Some are easier to detect just with your ear, if not you can spray brake clean around the engine and get a variation in the idle and pinpoint where the leak is by doing this.

@mostafajbeily4529

Жыл бұрын

Thanks alot man. I've done a head gasket change on the engine about a month ago btw. Does that have anything to do withit

I’m having a problem where my Infiniti will lose acceleration power while driving but I still have power in the car but if I turn it off the car wont start back up unless I jump it😩

@TheAutoTeacher

Жыл бұрын

Are there any codes ? Sounds like you could have a bad battery with a dead short in it which can cause many different scenarios . I would take it out and have it tested at any local automotive parts store.

@lessmilez91

Жыл бұрын

@@TheAutoTeacher I got a new battery but it still said voltage low

@TheAutoTeacher

Жыл бұрын

Did they check the output of your alternator ?

@DrJames_YT

6 ай бұрын

@@TheAutoTeacherI got the voltage low code

Which one is the bank 2

@TheAutoTeacher

Жыл бұрын

Bank two is on the drivers side.

@pablogarcia8188

Жыл бұрын

Hey did your engine light go away after getting a new one ?

@juanrenteria4585

Жыл бұрын

I just got the code today PO101 & PO10B (Bank 2). Im going to clean both sensors tomorrow. Thanks for the video, this really helps. 😊

@violetaperez3489

10 ай бұрын

@@juanrenteria4585did it work ? i just got those today

@yungrichrico2159

2 ай бұрын

@@juanrenteria4585was your car having acceleration problem with those codes

What size are the bolts holding the sensor in?

@TheAutoTeacher

21 күн бұрын

I'm told it's Screw - Nissan/Infiniti (08360-41226). You can take one from the other side and try to match it at your local hardware store or proceed directly to your local dealer.

@gsteel98

21 күн бұрын

@@TheAutoTeacher thank you, I'll see today or tmr, hoping my 10mm will be enough to take them out since I noticed they don't have the slit for a screwdriver like the ones holding the tube