How to Clean a Paint Sprayer [Airless Paint Sprayer Cleaning Instructions] Graco Magnum X5 X7(2019)
Тәжірибелік нұсқаулар және стиль
How to clean a paint sprayer. Graco magnum x7 Airless Paint Sprayer Cleaning Instructions. Graco Magnum X5, Project Painter Plus, LTS 15, LTS 17, magnum paint sprayer.
1. Move intake tube from paint and move to clean water, leave waste tube in paint
2. With sprayer in prime position toggle power switch until water comes out of the waste tube.
3. Move waste tube to clean water
4. With sprayer is in spray position pull trigger then toggle power switch until water has cycled through the machine a few times.
5. Discard dirty water and start with fresh
6. Repeat as needed.
7. Subscribe to my channel kzread.info...
8. Thank you for your support!!
If you have a Graco Magnum X5 paint sprayer you will need to know how to clean a paint sprayer.. The process for cleaning a graco magnum x5 paint sprayer is the same process used to clean a Graco Magnum x7 paint sprayer. Cleaning the graco magnum x5 or x7 is also the same process as cleaning magnum lts 15 or graco magnum project painter plus. Follow the graco cleaning guide in this video and you will find yourself with a clean magnum paint sprayer.
00:00 I hope to earn your subscription today
00:06 How to clean a paint sprayer
01:46 Paint Sprayer Cleaning
03:16 Cleaning a Paint Sprayer
04:46 Graco Paint Sprayer Cleaning
5:45 I hope I have earned your subscription today. Thanks for watching.
#GracoMagnumX5
#paintsprayer
#gracopaintsprayer
Пікірлер: 118
Love your videos! So quick and concise! Makes it so easy. Thank you!
@DIYAllied
9 ай бұрын
Thank you. I appreciate that.
@user-oe3oo9vs8m
4 ай бұрын
Unlike the Graco Videos.
Thank you for recording this and for ignoring the critics.
@DIYAllied
7 ай бұрын
Thanks for commenting. I appreciate that.
I taking the whole machine apart. To keep your seals good..1 shouldn't leave paint in machine to dry. If it has paint and as long as no air is going in, paint will not damage seals, unless the paint freeze. So dont leave paint or any fluids in any freezing conditions. Once you clean it with water try to remove as much water from equipment and pour some pump fluid if you going to store machine or it will be in freezing weather. If you leave water in machine and air gets in it, you will built corrosion or any water build up minerals, with time if you do it alot it will wear out the metals and it will leak out from the piston.
Good video man. Good idea with toggling the power switch to get the rest of the paint out of the lines.
@DIYAllied
5 жыл бұрын
Thank you. I really appreciate it.
Great informative vid...thank you!
@DIYAllied
7 ай бұрын
Thank you.
Thanks for the vid! Thor's helped me a lot!
@DIYAllied
4 жыл бұрын
No problem. Thanks for commenting.
It was helpful and quick to do
Great Vid, Keep them coming.
@DIYAllied
4 жыл бұрын
Thank you. Thanks for watching.
thank you
@DIYAllied
7 ай бұрын
You are welcome.
I just found out that if you want to store your machine with water in the pump it will rust and break it, you gonna want to use mineral spirit, wind shield wiper fluid or that blue pump armor fluid it comes with the machine went you buy it. But yeah be careful with water it will rust out the pump.
@DIYAllied
9 ай бұрын
Agreed. Do not store your machine long term with water. I use pump armor when I do.
When you clean up after water based paint, it is better to connect Graco the the water hose. You will save some pump life as water will run by it self
@DIYAllied
Жыл бұрын
In the summer at least. Here where it freezes solid most people don't have access to a hose in the winter.
Great video and thankyou very much💪💪💪🍺🍺🍻
@DIYAllied
5 жыл бұрын
You are welcome. I'm glad you liked it. Cheers.
you never mentioned cleaning the filter in the gun handle. Its madatory to remove it and clean it or the filter will become clogged from hardened paint and the gun will not operate.
@DIYAllied
2 жыл бұрын
Its a good practice.
Thank you
@DIYAllied
6 ай бұрын
You are welcome.
This was the most concise video explanation I've seen so far. I knew there had to be a way to salvage some of the paint in the lines. Thanks for the info!
@DIYAllied
Жыл бұрын
Thank you.
I save a lot of Folgers coffee cans. They are great for painting with a brush. I see you like them too.
@DIYAllied
3 жыл бұрын
I don't function in the morning without about 4 cups of coffee💪
@zapatastyle
2 жыл бұрын
The best containers for painting with a brush are 2L juice cartons cut to about 4". Been using them for my work for over a decade.
I got one of these machines at a garage sale. 50 bucks. Only problem is that it has dried paint on it and in it. If this don't work can i run like paint thinner through the machine?
The filter inside the gun has to be changed on every painting service?
@DIYAllied
Ай бұрын
Nope. Just clean it as needed. Replace it if it has holes or is damaged.
Would you use water or mineral spirits to clean acrylic paint?
@DIYAllied
3 жыл бұрын
Water
Do you know if it’s clogged with debri or chunks of dry paint make it stop spraying and also when pressing the trigger nothing comes out or very little does but with no pressure at all
@derekd1203
3 жыл бұрын
Turn machine off. Turn to prime for few seconds than back to soray
@AntonAtan
2 жыл бұрын
Probably I'm too late with that comment. I spray only thick undercoat and whenever it gets clogged I turn the tip in reverse, spray once and turn it back to forward position. Ussually that helps. The spray gun have a filter in the handle. Make sure you clean it. Even after running water through the pump filter is still dirty.
@lcan9447
2 жыл бұрын
there is a filter in the handle that will cause that problem if its never cleaned after every use.
Why are you cleaning it this way when it’s fast flush compatible? Hook a garden hose right up to it don’t even need power?
@DIYAllied
2 ай бұрын
I use sprayers all winter long. It doesn't work to drag the hose through the snow to flush it. Feel free to come up with your own solution to cleaning it in the winter if this video doesn't help.
Question Are you storage this painter with water inside it It will not rust??? I'm cleaning mine for first time so ya I don't know
@DIYAllied
22 күн бұрын
You can store it for short periods of time with just water. Longer than 7 days i would use pump armor.
Can you store the machine with warm water inside for a month between usages if you relieve the pressure to protect the seals and Gaskets?
@DIYAllied
4 жыл бұрын
I have done that in the past but wouldn't recommend it.
@aaronstestlab
4 жыл бұрын
Not unless you want to corrode your pump. You should store it with pump armor, antifreeze or mineral spirits.
@tundrawhisperer4821
3 жыл бұрын
Incorrigible Aaron is it true that pump armor can dry up on the internal parts over time? Better to use mineral spirits for long term storage? Thx
Is this the process or at least the same process for latex paint?
@DIYAllied
5 жыл бұрын
Yes it is
Great! I just did it! Graco pump armor.
@DIYAllied
4 жыл бұрын
Awesome. Thanks for watching.
No pump armor for storing??? Works great.
@DIYAllied
3 жыл бұрын
For long term storage, yes I do.
I forgot and left water in my Magnum X5 for about 5 days. It is a brand new pump and I only painted with it once. I cleaned it with water and forgot to go back and add the cleaner. Did I do damage to the pump? How can I tell?
@DIYAllied
4 жыл бұрын
It should be fine. Try to run it with some more water on low pressure. If it primes and makes pressure It's good to go. If water leaks from the bottom of the machine when pressurized the seals are toast.
@shawnlewis389
4 жыл бұрын
@@DIYAllied Thanks. I did that and it works fine. Ran some paint through it to paint some 4X8 foam insulation board. Then I cleaned it with water and ran the storage solution through it.
@DIYAllied
4 жыл бұрын
@@shawnlewis389 Excellent.
Do you leave the water in the tube or do you drain out all the water?
@DIYAllied
2 жыл бұрын
I leave the water in the machine unless I'm storing it long term. Pump armor should be used if you are storing it for longer than 2 weeks.
I just flushed both sides until clear. Way faster and looks like new still.
@DIYAllied
Жыл бұрын
That method works fine in the summer but in cold climates in the winter its just not possible to simply connect to a hose.
leaving the waste in the paint and intake in the water, does that not pull water into the paint?
@DIYAllied
3 жыл бұрын
It does yes. Just void that paint/ waste when you set up the next time.
Fuckin a buddy good video. If you were in Colorado I'd buy you a beer
@DIYAllied
4 жыл бұрын
Thank you sir. Cheers
Messy, messy messy. So, what do you do with the filters? And where do you dispose of the waste water? OSHA and the EPA would like to know...
@DIYAllied
2 ай бұрын
Bring it.
It should be in here but it's not. Clean the filter in the gun handle also.
@DIYAllied
2 жыл бұрын
Yup. I have a seperate video on that but i should have included it in this one as well.
My sprayer primes but when I go to paint nothing comes out of the gun or it just a spirt. I dont know what to do and can't find any help. Can you help?
@DIYAllied
3 жыл бұрын
Have you checked the filter in the gun? Make sure to release all pressure before attempting to check it. The tip may be clogged also. Did you try reversing the tip?
@jtoborkey
3 жыл бұрын
@@DIYAllied yes I cleaned both really well. I also tried the unclog method on the tip, still nothing. I only used it once and cleaned it afterwards
@DIYAllied
3 жыл бұрын
@@jtoborkey This sounds like a tip clog to me. You might be surprised how many times they clog repeatedly if there is debris in the paint. Just a few chunks of dried paint breaking off from inside the tip can cause repeated clogs. I would clean the tip with a pin until I could clearly see light through it. Cycle some paint through the machine, reinstall the tip and give it another shot.
Looks like a PIA to use
@DIYAllied
Жыл бұрын
As paint sprayers go, this is one of the easier ones to use.
Is there any way if spraying pipe is all clogged with paint inside
@DIYAllied
2 жыл бұрын
Yes it is possible.
@AnkushKumar-xv6tr
2 жыл бұрын
@@DIYAllied I just bought this machine in an auction and found its all clogged up moter runs but no suction and pipe is also blocked what should I do Thank you for your reply tho 😊
@DIYAllied
2 жыл бұрын
@@AnkushKumar-xv6tr I would first check to see if the hose is completely clogged. If it is you may need to get a new one. If not you should check the intake and outlet valves. I have a video on my channel that can help you.
need to clean filter in the handle..
@DIYAllied
4 жыл бұрын
Yes. I have a separate video for that.
I know how to clean paint from my sprayer, but what about cleaning lacquer ..... HOW TO?
@DIYAllied
5 жыл бұрын
Will do.
What do you do with all of the dirty paint buckets filled with water/paint in them?
@DIYAllied
4 жыл бұрын
We almost always use latex or acrylic/latex which is non toxic so it's safe to pour it down the drain. Just dilute it. Oil based products require flammable-toxic liquids to flush the spayer and need to be disposed of properly.
@terrywalton4081
3 жыл бұрын
Lk
أعرف كيف أنظفه من الصباغة المائية لكن كيف أنظفه من الصباغة الزيتية 👋👋👋💖
@DIYAllied
3 жыл бұрын
استخدم المشروبات الروحية لتنظيف المنتجات الزيتية
lol this guy dont look like he ever cleaned his sprayer
@DIYAllied
2 жыл бұрын
Funny.
Next video is how to replace a broken switch. Just kidding. Interesting way of avoiding that annoying sound. Would you clean the other Graco pumps this way?
@DIYAllied
5 жыл бұрын
Lol. Probably right. Although it hasn't happened yet.
@DIYAllied
5 жыл бұрын
Honestly I think you could clean the others this way, if you wanted to.
@craigcode7103
4 жыл бұрын
@@DIYAllied When is your video on how to replace a toggle switch?
@DIYAllied
4 жыл бұрын
@@craigcode7103 Switch is still going strong
Thanks for the video. I paint twice a week two days in a row. How would i go about storing it for the five days in a row i don’t use it? Do I need to use the pump armor? Also what about overnight between jobs? Thanks again.
@DIYAllied
5 жыл бұрын
For overnight jobs I usually leave the sprayer set up but I let the pressure off by switching it off and switching it to prime. Leave a wet towel over the intake tube and paint can to prevent it from forming dried skim of paint in the can. If it does dry a little just remove the dried stuff before you start the next day. If you are going to leave it for more than a day of two I would suggest using the process in the video but there is no need for pump armor. I only add pump armor when I'm storing for more than a week, which is pretty rare in my case.
Why are you cycling that dirty water? Lol.
@DIYAllied
4 жыл бұрын
It's paint and water. What's dirty about it?
@MrC9Oh3
4 жыл бұрын
@@DIYAllied the paint in the water, pointless to cycle that
@DIYAllied
4 жыл бұрын
@@MrC9Oh3 Do as you like man.
Nothing about cleaning the filter in the handle... or did I miss that?
@DIYAllied
5 жыл бұрын
I have another video explaining how to clean the gun
Did you forget to clean the gun filter?
@DIYAllied
4 жыл бұрын
Yes, I did leave that out of this video but I do have another video about that. I should have included it.
Totally wrong way too do it
@DIYAllied
3 жыл бұрын
Ah I see. Lol
Look how filthy my spray gun is and let me show you how to clean yours
@DIYAllied
2 жыл бұрын
Nice. I subscribed.
Thank you
@DIYAllied
2 жыл бұрын
You are welcome.