Watch this video to learn to proper way to check and set rollers!
Жүктеу.....
Пікірлер: 63
@stewartpereira54422 жыл бұрын
Thank you for an informative video, heidelberg has made it so easy , Happy Printing!!
@Loosu12 жыл бұрын
Thank you very much. You are a really back bench student in engineering college. 😁😁Your pronunciation is easy to understand for non English speaking country people.
@rons91973 жыл бұрын
The auto set film guide is a handy tool. That is what the master pressman would have known with his experience. Now you just need a company that believes in keeping good rubber on their machines and giving the time for maintenance.
@Kegga_6
2 жыл бұрын
Exactly, put in 8 sets of westland epmd with loto tec pans 6 months later still running strong with minimal adjustments. The roller assistant is a really good toll in a crunch
@dangquesadilla
Жыл бұрын
I always said.... you're either gonna have scheduled maintenance or unscheduled maintainence. Your call boss
@manokaranrajan57087 жыл бұрын
sir tell me about roller setting of sx 52 machine on plates where is the setting bolt please send me the video.
@FridayBluemoon5 жыл бұрын
Thank you my friend.
@dirkayala58127 жыл бұрын
Whats the specific name of that foil at 4:33,(for ordering purposes)?...Thanks
@zubizubair80935 жыл бұрын
How much rubber rollers plate cylinder hadnes . ?
@richardprasad23669 ай бұрын
Thanks sir. Lessons good.
@godfreyadede19756 жыл бұрын
THAT WAS A WONDERFUL DEMONSTRATION,KINDLY DO ONE ON DAMPENNING SETTINGS SINCE LITHOGRAPHY INVOLVES INK AND WATER AT THE SAME TIME.THANKS AGAIN
@peterhalbert1783
3 жыл бұрын
I did one on the dampers, Heidelberg USA thought it was too long at over 30 mins. Sorry for that.
@rohitchettri10312 жыл бұрын
Sir i m operating mov from heidelbrg usa and it has inkdock problem can u give me some solution about that
@miankhuram78694 жыл бұрын
Nice job dear
@renegagnon997 жыл бұрын
Great video.
@peterhalbert1783
3 жыл бұрын
Thanks
@sampharom85102 жыл бұрын
Could you show the tips how to setting paper run ?
@HoPrinting6 жыл бұрын
Best person to advice
@johnhflee64352 жыл бұрын
Hope many print engineers watch this and apply to daily operatiom.
@tommcdonnell45317 жыл бұрын
Helpful. Could you make a video to show the best way to adjust the water unit settings and also if possible step by step on the ink rollers. XL 105 if possible. You don't do it every day and the video is helpful when it's time to do it
@druckerman247
4 жыл бұрын
The skew setting on the dampeners is a bitch but it works well when you understand it.
@idreeskashi1253 жыл бұрын
Hi sir can you make another more videos about different kinds marks in our printing then how to solve that's problems to machine from roller and dampening thanks
@makeitperfect55136 жыл бұрын
Any job vacant in your company
@s.m.abidabid30826 жыл бұрын
i want to talk and help on printing machine
@antoniomoreira73 Жыл бұрын
I love your content, but I don't know English. Could it have subtitles in Brazilian Portuguese? Thanks.
@user-zq1dr3yh6o2 жыл бұрын
Bonjour. J'ai ma machine speedmaster 74 5 c année 2000 la l'arme de lubrification commence à sonner à partir de la vitesse de 3000 . J'ai changé l'huile,et le filtre. La pompe travaille la lubrification se fait ,la l'arme ne s'arrête pas. pourriez-vous m'enrienter.
@rexhenderson8503 жыл бұрын
I have a question, I have a one to two inch stripe across my blanket six to eight inches back from the lead edge of the blanket also I have a one to two inch stripe about six to eight inches back from the tail end of the blanket plate is clean can anyone tell me how to get rid of that never seen it before this is a new problem I have tried different inks and different fountain solutions next I'm going to try different plate material this is just started up this year any suggestions for me to try thank you
@beijingbiden5931
10 ай бұрын
So is it a waterline? I print folding cartons and I know on dark inks like frosted flakes for example I would get the image of a line across the box.
@katinta3702 ай бұрын
Nice
@jimbrown44566 жыл бұрын
A good scotsman by the sounds
@peterhalbert1783
3 жыл бұрын
Yes, you’re correct Jim.
@peterhalbert1783
3 жыл бұрын
Yes Jim, you’re correct. 🏴
@dimitrydaviddimi51257 жыл бұрын
mantap price
@mirzaubaid902310 ай бұрын
❤
@ramprabeshshaw22633 жыл бұрын
Describe detail about automatic work
@atanasoft19907 жыл бұрын
WOOOW
@rafaeljesus64363 жыл бұрын
muito legal! #speedmaster
@beijingbiden593110 ай бұрын
Lol that press prints with 4 ink forms. Thry took 3 of our i k forms out and i only print with 1 ink form and of course the water form.
@Raslinkprom5 жыл бұрын
Rolers bottcher or Westland?
@Kegga_6
2 жыл бұрын
Westland
@BDTubeJohir6 жыл бұрын
Please Damping Roll Settings video
@slcryptodc
5 жыл бұрын
yes i want
@edoybolo-bolo4461
5 жыл бұрын
Amazing question
@peterhalbert1783
3 жыл бұрын
I made a video on setting dampers, unfortunately Heidelberg USA thought it was too long.
@Kegga_6
2 жыл бұрын
The diagram and literature that Heidleberg provides on rollers setting is easy to use , yes it's nice to have a video but it does work, if your company can afford it a demonstrator can come in to show you, also Peter any openings in Kennesaw lol
@razibahamed64563 жыл бұрын
Wow good job.do you have a job
@ramukrish6053 жыл бұрын
Please job saving video sir.
@blessondaniel3 жыл бұрын
Happy Printing
@manokaranrajan57087 жыл бұрын
thanks for your good information sir
@vinodsunhare79884 жыл бұрын
RYOBI 524 HXX'S CPS MONITOR SYSTEM ABOUT WATER, INK, REGIGTER INSTRUCTIONS
@safikulislamrana45332 жыл бұрын
Ok sir
@SteveMK2 жыл бұрын
You didnt mention the recommended width of stripe on plate..
@Kegga_6
2 жыл бұрын
All forms to plate are 4-5 millimeters, except the water form which is 6 millimeters make sure your ink train is set in 1:2
@SteveMK
2 жыл бұрын
@@Kegga_6 thank you so much. I really appreciate thay
@Kegga_6
2 жыл бұрын
@@SteveMK no problem, may I ask what press your are running
@SteveMK
2 жыл бұрын
@@Kegga_6 gto 52 single.
@Kegga_6
2 жыл бұрын
@@SteveMK wow don't think I've seen a gto in 20 years, I started out running a 2c sorzs, here I am now running a 8c xl 106 new gen 2020 with 2 coaters and cold foil 30 years later it amazing how far the printing industry has come, but those older heidelbergs will never stop, I was running a 1956 windmill helping a freind out not to long ago
Пікірлер: 63
Thank you for an informative video, heidelberg has made it so easy , Happy Printing!!
Thank you very much. You are a really back bench student in engineering college. 😁😁Your pronunciation is easy to understand for non English speaking country people.
The auto set film guide is a handy tool. That is what the master pressman would have known with his experience. Now you just need a company that believes in keeping good rubber on their machines and giving the time for maintenance.
@Kegga_6
2 жыл бұрын
Exactly, put in 8 sets of westland epmd with loto tec pans 6 months later still running strong with minimal adjustments. The roller assistant is a really good toll in a crunch
@dangquesadilla
Жыл бұрын
I always said.... you're either gonna have scheduled maintenance or unscheduled maintainence. Your call boss
sir tell me about roller setting of sx 52 machine on plates where is the setting bolt please send me the video.
Thank you my friend.
Whats the specific name of that foil at 4:33,(for ordering purposes)?...Thanks
How much rubber rollers plate cylinder hadnes . ?
Thanks sir. Lessons good.
THAT WAS A WONDERFUL DEMONSTRATION,KINDLY DO ONE ON DAMPENNING SETTINGS SINCE LITHOGRAPHY INVOLVES INK AND WATER AT THE SAME TIME.THANKS AGAIN
@peterhalbert1783
3 жыл бұрын
I did one on the dampers, Heidelberg USA thought it was too long at over 30 mins. Sorry for that.
Sir i m operating mov from heidelbrg usa and it has inkdock problem can u give me some solution about that
Nice job dear
Great video.
@peterhalbert1783
3 жыл бұрын
Thanks
Could you show the tips how to setting paper run ?
Best person to advice
Hope many print engineers watch this and apply to daily operatiom.
Helpful. Could you make a video to show the best way to adjust the water unit settings and also if possible step by step on the ink rollers. XL 105 if possible. You don't do it every day and the video is helpful when it's time to do it
@druckerman247
4 жыл бұрын
The skew setting on the dampeners is a bitch but it works well when you understand it.
Hi sir can you make another more videos about different kinds marks in our printing then how to solve that's problems to machine from roller and dampening thanks
Any job vacant in your company
i want to talk and help on printing machine
I love your content, but I don't know English. Could it have subtitles in Brazilian Portuguese? Thanks.
Bonjour. J'ai ma machine speedmaster 74 5 c année 2000 la l'arme de lubrification commence à sonner à partir de la vitesse de 3000 . J'ai changé l'huile,et le filtre. La pompe travaille la lubrification se fait ,la l'arme ne s'arrête pas. pourriez-vous m'enrienter.
I have a question, I have a one to two inch stripe across my blanket six to eight inches back from the lead edge of the blanket also I have a one to two inch stripe about six to eight inches back from the tail end of the blanket plate is clean can anyone tell me how to get rid of that never seen it before this is a new problem I have tried different inks and different fountain solutions next I'm going to try different plate material this is just started up this year any suggestions for me to try thank you
@beijingbiden5931
10 ай бұрын
So is it a waterline? I print folding cartons and I know on dark inks like frosted flakes for example I would get the image of a line across the box.
Nice
A good scotsman by the sounds
@peterhalbert1783
3 жыл бұрын
Yes, you’re correct Jim.
@peterhalbert1783
3 жыл бұрын
Yes Jim, you’re correct. 🏴
mantap price
❤
Describe detail about automatic work
WOOOW
muito legal! #speedmaster
Lol that press prints with 4 ink forms. Thry took 3 of our i k forms out and i only print with 1 ink form and of course the water form.
Rolers bottcher or Westland?
@Kegga_6
2 жыл бұрын
Westland
Please Damping Roll Settings video
@slcryptodc
5 жыл бұрын
yes i want
@edoybolo-bolo4461
5 жыл бұрын
Amazing question
@peterhalbert1783
3 жыл бұрын
I made a video on setting dampers, unfortunately Heidelberg USA thought it was too long.
@Kegga_6
2 жыл бұрын
The diagram and literature that Heidleberg provides on rollers setting is easy to use , yes it's nice to have a video but it does work, if your company can afford it a demonstrator can come in to show you, also Peter any openings in Kennesaw lol
Wow good job.do you have a job
Please job saving video sir.
Happy Printing
thanks for your good information sir
RYOBI 524 HXX'S CPS MONITOR SYSTEM ABOUT WATER, INK, REGIGTER INSTRUCTIONS
Ok sir
You didnt mention the recommended width of stripe on plate..
@Kegga_6
2 жыл бұрын
All forms to plate are 4-5 millimeters, except the water form which is 6 millimeters make sure your ink train is set in 1:2
@SteveMK
2 жыл бұрын
@@Kegga_6 thank you so much. I really appreciate thay
@Kegga_6
2 жыл бұрын
@@SteveMK no problem, may I ask what press your are running
@SteveMK
2 жыл бұрын
@@Kegga_6 gto 52 single.
@Kegga_6
2 жыл бұрын
@@SteveMK wow don't think I've seen a gto in 20 years, I started out running a 2c sorzs, here I am now running a 8c xl 106 new gen 2020 with 2 coaters and cold foil 30 years later it amazing how far the printing industry has come, but those older heidelbergs will never stop, I was running a 1956 windmill helping a freind out not to long ago
Nice