How to change the Unloader | Kranzle Pressure Washer
Was this video helpful? Please LIKE|SUBSCRIBE|COMMENT
Check us out on Instagram - bit.ly/kranzle_
For the latest prices and specifications visit - bit.ly/kranzleunloaders
_____________________________________________
📞01925 44 44 64
💻 www.kranzle-pressure-washers.c...
📧 info@aquaspray.co.uk
📸@kranzle_
🐦 @kranzlepressure
📺 Kranzle Pressure Washers
-------------------
#kranzle #aquaspray #parts
Disclaimer: you accept all responsibility for any damage or injury to yourself or others if following any of my videos.
it is sad I have to put this, but if you do something wrong you could damage your machine or hurt yourself or someone else.
Пікірлер: 51
Wow, can't believe my grandfather's West German pressure washer had the unloader valve locknuts set at the wrong threads all these years. It had full pressure all the years but wouldn't do lower than 60 bar. Goes all the way now without the nylon nut backing out all the way. I suspect it might be the original unloader valve as it needed some new grease but other than that, no blockages, marks, cracked or rotten o-rings etcetera. And its been used by his painting/all-round maintenance business ever since the fall of the berlin wall. Still rocking the old 125.
Great sir
Super
Hi, my kranzle is only giving low pressure that red nob usually springs out when I pull the trigger on lance but has stopped doing that, resulting in low pressure I adjust it but no difference?
@KranzlePressureWashers
3 жыл бұрын
DM me on Instagram with a video of the pump @kranzle_ 👍
Is there any maintenance on the other side of unloader. Or as long as the spring in the valve works is it all good?
@KranzlePressureWashers
4 жыл бұрын
yes there is a Ball, Seat and Spring at the other side of the unloader, are you having troubles?
@garybyrne2420
4 жыл бұрын
Kranzle Pressure Washers the unloader doesn’t increase or decrease the pressure at the gauge. Only goes to about 650 psi. Will it be the O rings on the unloader as the end of it doesn’t seem to be distorted in any way?
Might be a stupid question but should you wind (clockwise) the unloader valve all the way in?
@KranzlePressureWashers
Жыл бұрын
If the unloader is set up correctly and the unloader is wound in the machine will be on full pressure If it’s wound in and the unloader is not set up correctly then the machine will unload at a too high pressure
I have a kranzle160 TST. Left it out in the recent heatwave doubt that was the real cause lol. However the actuator is not operating the push switch. It's a attach to the pump body behind pressure gauge. Any suggestions please
@KranzlePressureWashers
Жыл бұрын
It would be better if I see it running find me on Instagram @kranzle_ send a message
@MrSagsta
Жыл бұрын
@@KranzlePressureWashers managed to fix it. It was a limescale build up in the actuator. It's hardly used so guessing sitting there for prolonged times can be enough for it to build up. Gave it a good clean, and a little silicon grease. Still figuring out what the two grub screws are for at the top. Look like a service points, but can't see it to be used for oiling actuator as there's water in there. Thank you for your quick response
Hi, How to modify a Kranzle HD 7/122 becomes a HD 7/122 TS, using original parts?
@KranzlePressureWashers
3 жыл бұрын
Only a few 7/120’s where made with a pump that you convert to the TS by adding the switch and piston, if you don’t have that style pump then it would be too expensive to convert
How do I adjust the psi I noticed mine only goes to 1300 when it’s rated for 1800. Also need to state is I barely use mine and don’t have much knowledge about these pressure washers 😬
@KranzlePressureWashers
3 жыл бұрын
Normally screw the red knob in all the way, Sometimes if it’s mot set right and the red knob stops before getting to full pressure you may need to adjust the 2 nuts a few threads
@jspecmedia
3 жыл бұрын
@@KranzlePressureWashers thank you so much I’ll try both of those methods and get back to you!
My kranzle 1322ts is surging when stopped. When the trigger is pressed it works fine. No drop of pressure on gauge when pressed. When the trigger is released it surges every 15-20seconds. What would cause this issue? Thanks
@KranzlePressureWashers
3 жыл бұрын
Check for any small leaks anywhere 1st If not that the back stroke ball may need reseating
@kidbanga10
3 жыл бұрын
@@KranzlePressureWashers no small leaks
@kidbanga10
3 жыл бұрын
@@KranzlePressureWashers do you have a video on reseating the back stroke valve?
@KranzlePressureWashers
3 жыл бұрын
@@kidbanga10 either email me or contact through Instagram @kranzle_
Where can I get a new unloader?
@KranzlePressureWashers
3 жыл бұрын
Check the link in the description 👍
@motomuscl3
3 жыл бұрын
I’m in US
@KranzlePressureWashers
3 жыл бұрын
@@motomuscl3 I can recommend Detail division, or kranzle USA (dirtkiller)
Any info or links at all?????
@KranzlePressureWashers
3 жыл бұрын
Give us a call or email kranzle-pressure-washers.co.uk
I’ll be doing this in a couple days : I received my machine with a bent unloader 😔
@KranzlePressureWashers
3 жыл бұрын
Oh no 🥺
@jjjjjjjjjjjhjjjjjhjj
Жыл бұрын
Yeah same here
I've tried an 8mm socket and it doesn't fit in and I've got a thin socket and still doesn't fit any help
@KranzlePressureWashers
3 жыл бұрын
Needle nose pliers and just hold the nut 👍
@nathanbarker3789
3 жыл бұрын
Just tried it, still no luck. What socket did you guys use
@KranzlePressureWashers
3 жыл бұрын
@@nathanbarker3789 screw the unloader in tight you should be able to get the socket or spanner to catch
@nathanbarker3789
3 жыл бұрын
@@KranzlePressureWashers I am replacing the full unloader as its failed and is stuck on low pressure
@kerndetailology7632
3 жыл бұрын
You ever get it?
Bought one of these brand new, 1152 tsp , £750 from a main dealer, pulsing straight out of the box, checked the unloader and the soap pick up hose junction for grit, nothing! At least the Karcher with its crappy plastic pump waited 5 years to start it! Best in the world, bombproof, never give bother!.........yea right, going back for another crappy karcher.
@KranzlePressureWashers
3 жыл бұрын
An brand new 1152tst pulsing straight out of the box, sounds like the outlet “back stroke” valve needs reseating & would be a 5min fix for the dealer you bought from. It is uncommon for a new machine to do that so you are unlucky, but hey that’s why you get a proper warranty 👍 hope you get it sorted and don’t get to disheartened
@beano6584
3 жыл бұрын
Thanks for the prompt reply! Just bugs me a brand new unit has to be messed about with, don’t suppose you have and vids or links as to how to do that? Dealer is over an hour away from me and god forbid I let them fix it and it happens again!
@beano6584
3 жыл бұрын
Sorry for venting, just a bit miffed, great vid btw :-)
@KranzlePressureWashers
3 жыл бұрын
Go to our website and Send me an email or give me a call
Can I heck find a 8mm socket with a thin enough wall to fit.
@KranzlePressureWashers
Жыл бұрын
The 8mm nut should not be screwed into the red knob it’s only there to stop the knob unscrewing and coming off, if the threads are gone and the knob can’t screwed in to reveal the nut, you may be able to hold the nut with a small screwdriver and turn the knob to take the nut off
@falcondetailing2564
Жыл бұрын
@Kranzle Pressure Washers got it off...the threads stripped down by the 2 10mm nuts shards of what I assume is the washer in the thread too that's why the red handle popped all the way back I think. If I Spin the handle all the way to the spring it doesn't tighten there just spins...New part needs ordering...least I found the fault thanks to your video mate
@KranzlePressureWashers
Жыл бұрын
@@falcondetailing2564 kranzle-pressure-washers.co.uk/products/genuine-kranzle-red-knob-only-for-unloader-pressure-adjuster-valve-43049?_pos=1&_sid=03e559d90&_ss=r
My unloader valve arrived bent and I am trying to replace it , it is so difficult I just can’t do it :(
@KranzlePressureWashers
Жыл бұрын
What’s causing the issue it should just unbolt with 19mm spanner