I wont believe that this is a functional turbo until you make a video of the bike running

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

@jbrennan381

3 жыл бұрын

@Elliot Dane you're a terrible scam artist, but I admire your dedication

@pleasedontwatchthese9593

2 жыл бұрын

@@HiteshMistry0 keep up the good work, dont let the haters get to you

Thank you for this video.💕. tomorrow is installing to new turbo charges in my motorcycle

@sachingehlot3129

3 жыл бұрын

Bro you installed ??

@desilonde3213

Жыл бұрын

Tell me bro u installed ??

The turbo oil return should be at the highest point of the crank case.... nice work bro 👊

@shortattentionspangarage1312

2 ай бұрын

Not necessarily. The oil just needs to be able to drain down out of the turbo and above the level of the oil in the pan.

Turbo not recommend in single cylinder engine. due to the timing mismatch between the exhaust stroke, when the turbocharger is powered, and the intake stroke, when the engine intakes air.

Legend says this guy still figuring out how to start this bike.

Wats the size of the turbo installed and is it petrol or diesel turbo

Bro where did you buy the parts for those turbo

When i started the video i got surprised because i wanted for same bike 😁 Perfectly. Can i get link for the product (turbocharger)

I didn't understand why did you had to change the position for the carb. When the air pipe from the turbo could have been supplied directly into the air box

@ShailuBoi

3 жыл бұрын

Yeah. He should've added the turbo air outlet to the carb directly. Carburettor attached to the turbo intake manifold is wrong

@shameermalik5540

2 жыл бұрын

Turbo compresses the air, there is no room in it for fuel that will be sent by the carburetor in this setup.

@MrBobby-yg2nv

2 жыл бұрын

@@shameermalik5540 isn’t the bike fuel injected

@ferrumignis

Жыл бұрын

Blow through is more difficult to set up, you can't just pressurise the air going into a carburettor as it will push all the fuel out of the fuel bowl. You have to have a pressurised fuel feed with a regulator referenced to boost pressure.

How the engine gets gasoline you put down the carborator. does it have gasoline pump ..can you start the engine so that we can believe that..

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

What turbo did you use? Where did you get it, whats the size

@nikhilkharate7493

3 жыл бұрын

I need the answer too

Can we fit turbo charger in 220f ?

If I put a turbo on my SSR 125, will it last as long as without and if I turbo it does that mean that it will break a lot and I will have to fix it?

Stock speed 75 MPH, Turbo charger add speed 75.2 MPH

@nikhilkharate7493

3 жыл бұрын

😂😂😂

Bhai kon sia gade ka turbo use keya hia ?

How to select suitable turbo for 500cc bullet classic

Does it work??

Cuánto de aceite tiene que llevar después de una modificación de turbo moto.??? Quiero saber si se deja con su misma medida ho cambia.

Bro great video 🔥🔥🔥

what turbine compressor is that?

अच्छे तरह से फिटिंग किया टरबो को किसी छुपने वाले जगह पर सेटिंग करो, अच्छा लगेगा! Your work is perfect👍

Bhai tried well 🖤

bro, I think carborator se ek line engine me jani chahiye thi naki filter box me 🤔

Good job parmatma apko saffal ralhe sur spp ese ese project bna te rho

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

what is the model of that turbo?

Good. I will try this. 👍👍

Can I do this with a ktm 690 smc r? How?

Would it be the same concept on a predator motor on a motorized bicycle

@GODSWORD11

5 ай бұрын

No

does it make it fast

Awesome bhai 🔥🔥

Major props

Sir yamaha bond use karo oil leak band ho jaaye ga

Nyce bro you did great

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

Will it run??😅 postion of carburetor is not olay

I heard that putting 1 cylynder engine with turbo is not good that can cause and high presure explosion they say

the turbo can spooling in 7000-8000rpm.to high to increase boost.set on blowthrough carb.fuel pump and fuel rgulator.get small turbo rhbvz21 can spooling in single cylnder at 6000rpm.but problem oil pump in mtrbike not enough pressure to lubricant journal bearing .

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

Price of the turbos...?

Hitesh bhai turbo konsi gaadi ka h.

Is it working or ?

Mujhe diesel bullet me install karna hai kis tarah hoga

What's the cost of turbo?

Turbo usi engine me legta hey jis gadi me direct injecter hotata hey kay bullet me direct injecter hey

How can he use the brake pedal?

Those funnel fittings will choke airflow going into the engine..

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

amazing idea

it cannot work properly because the turbo will create overpressure in the carburetor pushing the mixture into the float

Bjai muje bhi kerna hai fit kha se milega and konsa turbo use hoga

Excellent bro 😍 ATLEATS you try it Love from Pakistan

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

Wht! How are you installing the inlet line from the turbo? No intercooler, no bov and not even a EFI engine.....dont do that bro....it might explode

@amardeeplmz8068

3 жыл бұрын

No bro it really works and once police there booked this bike rider for riding out at lightning speed of +300km/hr like Kawa-H2R in a public road illegally... Thankyou

@suprimksh8491

3 жыл бұрын

@@amardeeplmz8068 300km/hr + on the vm type carb 🤣🤣🤣 with no intercooler even bov no way bro...

Startup sound?

Abe exhaust pipe me turbo install kr rha ha bike start hote ho garam hawa se ya turbo ka swaha ho jayega

Turbo specifications

Were i can buy this turbo bro

Mario and Luidgi couldn't have done it better 😆

How to install Honda unicorn bro and price details

It has only added more weight to the bike. Now the 100 cc engine has to work harder to carry all that weight. Not sure if it would even start.

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

Awesome

Bhai kon se gaddi ka tarbo he tell me please

Turbo model ??

I don't think a "draw through" system will work when the carb is placed below the suction point try using "blow through" system and the inlet manifold seems restrictive compared to normal.

@neeljinwala

4 жыл бұрын

Totally. Useless.

@Dmzhunts

3 жыл бұрын

You.mean like she'll idle but run like shit under revs

@varunr2293

3 жыл бұрын

@@Dmzhunts yup exactly

@varunr2293

3 жыл бұрын

@@Dmzhunts the bike will become even more slower than before

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

bhai mere ko ntorq me laga na he turbo support karoge

How much it cost for this bro

Turbo price....Plz...Where is available turbo

Exhaust kidhr hai bhai

What's the benefits of adding turbo charge?

@HiteshMistry0

4 жыл бұрын

kzread.info/dash/bejne/nKhmt7aFZKTOoLg.html

RIP right shoes

Exhaust output kaha se

We'll try 👍👍

А куда делся карбюратор?

सर कोणसे गाडी का tarbo हे ? Plz बताव ना.

I admire your dedication and work, but you have a lot of flaws on your setup, biggest one is that your oil return is underneath the engine, and therefore underneath the oil. Oil return has too be over the oil line in the crankcase, it needs free flow without restriction. If you are still using your trainplug as a return, you need to use a scavenger pump too suck out the oil from the turbo, otherwise you’ll get oil leaks on the compressor or the turbine side of the turbo 🤷🏻‍♂️

bro atleast on mechanism u would hve left d braking space proper

bro .. carburetor is in wrong place .. put it direct to the engine again and then boosted it..

@jonathantang86

3 жыл бұрын

you got the right point

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

@HiteshMistry0

3 жыл бұрын

@@jonathantang86 kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

why did u put the carb between the turbo and airfilter? u have to filtering the petrol? lol

@johnroelpangaliman9673

26 күн бұрын

I was figuring out the same thing, its supposed to be air compressed not oil😂😂

Fz 16 me Jo sakta hai kya

Hello. Is this non-watercooled turbo?

@SurajSingh-zl9zt

4 жыл бұрын

Oil cooled

Bhai hf Deluxe par bhi turbo video banao

Everything is fine but the placement of turbo is towards the right so how come the bike would ride in an align form it would definitely get wobbled towards right side because the weight is more towards the right now

Tum sub vloger ko 1 hi music milta hi kya be

@Fatehyan

3 жыл бұрын

Tumhe kuch takleef hai kya be?

@coverbox1833

3 жыл бұрын

Aur vo vloger toh h ni

total cost kay huva

Ye turbo indica vista qutrazet ka h

Nice think but my things bike not produce best thrust for turbine work

Bro, mechanical engineering ke bad kya scope hai?

@shaswatsahay9326

3 жыл бұрын

Bike ki dukan khol lo😂

@advvaibhavvashisht9399

3 жыл бұрын

@@shaswatsahay9326 Hahaha vo toh khul ji jaege bhai uske elawa

Best video

I'm not a specialists about turbos and vehicles and i have zero experience, but i know the basics. A turbocharger is taking the air from already used gasses from the combustion chamber, that air is hot as fuck and the more you drive, the more hotter it will get. First things first, don't put a plastic pipe there. At first it will not break, but with time, you'll get issues beyond your imagination. I'm not talking about plastic dripping on your foot, i'm talking about plastic pieces in your engine. What? You think manufacturers are not going to use plastic pipes if they could? *They'll use plastic on every chance they get!* It's just that they use metal pipes *for a reason* Second - a turbocharger needs to put cold air into the combustion chamber and for that role an intercooler is needed. The main role of the intercooler is to reduce the temperature of the hot air compressed by the turbocharger, before it reaches the engine's combustion chamber. At this point, if you have issues with the boost, i am not going to be surprised at all. Cooling air into the engine is always going to be a good idea, as heat soak reduces the power of an engine. A turbo does heat air, simply by compressing it, but you will still get a direct benefit from any cooling you can do, either before or after the turbo. Any given volume of air has density. The difference in barometric pressure between observation sites at different elevations is a measure of the density of air in a column of air between those two elevations. Cold air is denser than warm air. In a nutshell, you need dense air to expand the explosion in the cylinder, but in reality, you're circulating hot air into a hot chamber and there's a chance that this air will get *even hotter* after driving for a while which can damage your engine BEYOND YOUR IMAGINATION ! :D

Good detail informative video keep it up। 10k like fore video editing and procesa stel by step

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

Cant saw the exhaust

he made of what he had at hand so

👍👍👍

Bhai ise start kakre to dikhata hume kase pata chale ga ye kam bhi karta hai ya nahi. Aise

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

Where is exaust . why not u start it

For turbo charger should be minimum 2 cylinders

@shaanamir4631

3 жыл бұрын

who said that?

@GODSWORD11

5 ай бұрын

Y is that???

Giving Cause for Fire in the Hole...

Does this engine start ? 🙃

@SajidKhan-xf2sw

3 жыл бұрын

😂😂Million dollar question

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

@gottetidineshbabu1078

3 жыл бұрын

There is the answer

Super

Orrr bhai break kaise lagani h ab

फायदा किया हुआ ,,,, इत्ती मेहनत के बाद में बाइक चलाकर दिखाई नही की किया परफॉर्मेंस रहा

@HiteshMistry0

4 жыл бұрын

This was our mechanical engineering final year project, we tried to put turbocharger in a single-cylinder engine but unfortunately, we failed. Because the turbo was not working well due to oil leakage.

@akashvishwakarma2929

4 жыл бұрын

@@HiteshMistry0 why you not put mini tubrochager and make a nozzle which is placed at carb side

Dai caiu da cama e acordou!!!

Bhai fuel itne lambe pipe se nhi jayega...

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html

I feel like that won't start.. what like a fuel will magically travel to the turbo then the carb to the bore

@jonathantang86

3 жыл бұрын

abslutly

@HiteshMistry0

3 жыл бұрын

kzread.info/dash/bejne/dXmLmdGYf6m_hdY.html&lc=UgyolMUUDZY1N4Eqpw94AaABAg

@sociallyawkwardguy7106

3 жыл бұрын

@@HiteshMistry0 but it's in the wrong side of the block Did you flip it You put the carburator in the exhaust port And the exhaust pipe In the intake did you change something like if the block is flip?

@sociallyawkwardguy7106

3 жыл бұрын

@@HiteshMistry0 oh wait I understand it now

@sociallyawkwardguy7106

3 жыл бұрын

@@HiteshMistry0 it's not flip the carburator fuel is moving up the in take sorry for misunderstanding