Isopropyl alcohol on a tooth brush for that flux splattering. Takes it right off and cleans up the flux crud from around your solder joints too for extra pretty builds.

@mrb2917

6 жыл бұрын

This is a must, the flux is corrosive you have to clean it up

Hey Bob, you wraskeley Builder!! I tuned into this video to learn a thing or two about a 'build'. I was not disappointed - as I followed along with your tutlage I found myself falling further and farther behind as the subject matters thickened. But I decided to hang on thru that build -my own excitement began to pump right along with you and that sweet drone would be ranked up there with the Chariots of the Gods!!! Maybe I didt not look hard enough but, I could find no trace of any follow-up. I dearly wanted to see that multi layer creation take the wind! I don't think that to fair for your troops of followers. And I'm sorry but, well I am very dissapointed in you... In fact, I was prepared to purchase a fresh new soldering iron and try mailing it out to you. A fresh can of pro flux-a roll of the finest solder available. Not to say anything negative about your work but, a proper rank of operating equiptment is essential. .........good lord >> did you botch that build? I think you did! GET A NEW SOLDERING IRON AND maybe take a class... thanks

The aikon ak32 Is another top 6s esc th top racers are using.

You short circuited the mosfet pads on the minute 19:04

@fpvdetailz712

6 жыл бұрын

Loudbeat FPV good eye... played back in slow 0.25 and sure enough solder splatter jumped over to mosfet

@loudbeatfpv560

6 жыл бұрын

Ty Adam schlichting, I just hope he sees it before he plug the battery or something will go wrong.

@PerBuch

6 жыл бұрын

Quite easy to se :-) Hope he gets it

@ShahZahid

5 жыл бұрын

They are all drain pins so no worries

@ShahZahid

5 жыл бұрын

@@PerBuch they are all drain (output) pins so no worries

It is an F7 board (and like the F3 boards) all the UARTs are uninverted/inverted :-)

Hobby wing g2 4 in 1 I the best esc now can't wait till you test one.

*Dj Khaled voice* ANOTHER ONE! Nice built as always. I wish all flight controllers had a better mic. Anyone knows of better mics. It's the same on everything that we use in fpv. I have it in a split and it could be better.

Nice good im in to building another one probably by next week. This video refresh my mind. Thank u for the video.

i have almost the same bild and its grate only down side to this vtx (this stac its realy tight and in front crush my battery strap riped of this white connetor from vtx with pads... i suggest to desolder this white connector and solder wires directy to bord you gain this way a lot of space and your vtx is secure.

You need the vtx telemetry to operate the atlatl.

F7 .. all uarts can be inverted :-)

you did it again! 👀 can't wait to watch the whole video 👻

F7 boards have automatic inversion.

You’re very brave using such a large soldering iron tip for such a small job...

Didnt leave the link for the SMA rubber grommet

Fantastic work, dude... It's already looking fast! 😮 That's going to be a beast!

@nikolasaustin916

3 жыл бұрын

i guess I'm kinda randomly asking but does anybody know of a good place to stream new movies online?

@bodietitan557

3 жыл бұрын

@Nikolas Austin Flixportal xD

@nikolasaustin916

3 жыл бұрын

@Bodie Titan thank you, signed up and it seems like a nice service :D Appreciate it !!

@bodietitan557

3 жыл бұрын

@Nikolas Austin No problem =)

Sweet build!!!! Cant wait 4 flight footage!!!!!! 👍😀👍

another badass build!

keep it up.. you do a awesome build video and explanation

I think there is smaller F7 chip out there, its of the size of f4

@Asu01

6 жыл бұрын

STM32F722 package

@patrickm5790

6 жыл бұрын

Yeah, the holybro kakute f7 uses the f745. The matek f722 uses a f722.

were can connet one relay, if need light or pump or somethink remote controll tranceiver switch,

What about GPS, getting into the hobby but I would like a fail safe?

F3 and F7 dont need inversion :)

I bought this flight controller. In the 8 pin plug, there is a pin tagged "I", between M1 and G. What is it?? It is not explained in manual. I ve a tekko32 metal 4in1 esc, and relative pad on ESC on the 8-pin plug is pin tagged "CURRENT". Dont understand :/

B-e-a utiful build. I've got some f60 pro ii's waiting to mate with those taco 32s (lol) I got from your shop. Can't wait to finally fly some t-motor and tekko32 awesomeness.

I was hoping you might add camera control as I'm trying to figure out if this works on bf 3.5. And if I'm using motor 5 what this looks like in setting up bf. Nice build vid though thank you

Looks fly as hell! Super Clean bro and the rubber grommet for the sma #softmounteverything lol

Test the foxeer lollipop on the atal mmcx

Why not soft mount the fc???

@rithiksawant

6 жыл бұрын

This fc does not need to be soft-mounted. I have the same stack and the kakute f7 already has a soft mounted gyro.

just a question, what will be the best suited motors (kv) and also propellers for a vet efficient and fast racing drone with 14.8 4S

Where to connect ibus

please give link to the sma rubber that you used.. good video :)

I would like to know if the "I" pin one the socket is for the current wire of the pdb

Good choice on flight controller and not using the Helios....

Can I watch some video flying this drone ?

Bro what is the Best Fc and ESC for 6S . Most reliable? Don't care about price

Current sensing is telemetry ??? Please ?

Other than pitching all the merch to pick up a tiny commission, did you ever add up the cost of all the parts? it'w well over $800 not including a controller. Might as well by the Mavic pro 2

@alexandert5960

5 жыл бұрын

J Smith mavic and fpv quad are very different

@mattivirta

4 жыл бұрын

thats controller cost maximum 20-24$ wery cheap and this frame cost 12-90$ and all other stuf together about 20-40$ not expensive. cheap can made this drone.

18:07 from where do you know wich wire you have to put on the right and wich one on the left?

Thanks for the video, can I use this board to power the DJi digital system? The system takes 4s but I plan to take advantage of the 6s capability of the board, but idk how to send power to it on this board

@Anonymous9683

5 жыл бұрын

You can wire up the power to a 9v output or any voltage within the permissible range, which I think is 7.4 - 17 volts or so. Just look at the wiring diagram of the board and find a voltage output in the range, then wire the red power lead to that and the black ground lead to the most convenient ground pad on the board.

There are less caps on this esc or not? Btw is it there also that hot as in the Netherlands?

Do you have the link to the solder you use? And what was the name of it again??

How tall is the whole stack FC+ESC+VTX? I wanna use it on a Martian 215mm anniversary edition, ty :)

God!! Why do so many people call it Holly bro????,the clue is the spelling "holy bro" it's a play on the phrase "holy brother"

This is waterproof?

"There's a newer virgin out"

Did you say you got your solder from Tesco ?

@mattivirta

4 жыл бұрын

ts100 have RC world popular solder tools, have more than all other solder tools. its best. only this board need change little tip better solden little pad.

6 inch arms have super mini micro small drone, why peoples buildmicro size mini mal drone, lot better and usefull have big 1x1meter or 0,5x0,5 meter ower 40 inc or mini size 20 inc drone have lot better size fly.

Atl-Atl... Same word twice..😁

69th like 😏

340 gram drone, this is joke, not drone. my next drone weight have about 20-23KG not gram. hahahaha or made little drone only second 10-12KG weight. same controller i think or kakute F7 board, and 80A ESC 8 pcs and 170KV motors 8 pcs. thats is perfect DRONE not joke.