That’s great info walkthroughs to bind TBS crossfire with TX16. I appreciate for the information. Thank you!

@RCVideoReviews

3 жыл бұрын

You’re very welcome.

One of the best walk throughs I have seen in a long time. I just got my micro V2 starter kit today and this will have me in the air tomorrow.

@RCVideoReviews

3 жыл бұрын

Thanks for watching and commenting. Make sure to wait for that solid green led. If not, the recovery procedure posted in comments does work. I've seen it go both ways :) I haven't flown mine yet, but I'm printing an Immortal v2 Antenna mount for my Mini Talon right now.

@petebuttons210

3 жыл бұрын

Agreed.

(DOUBLE GREEN BLINK FIX FROM TBS SUPPORT) The double blink means authentication failure. Please redo binding and follow the steps below. 1. Power off Tx & Rx. 2. Power on Rx. 3. Press the bind button on Rx. 4. Power on Tx 5. Start bind mode on Tx. Remember to check the antenna before rebind.

@RCVideoReviews

3 жыл бұрын

This is a good tip. I had to go through this with my first one because I disconnected too early. Thanks for sharing it here so we don't have to hunt for it :)

the "tool" I used for pressing the bind button is a "Q-Tip" with the cotton bulb cut off, you want to cut off the bulb with a sharp blade leaving a flat and smooth end cut. And the best part about the "tool" is it isnt conductive like metal etc. Its stiff enuf so you can feel the button click when it is pressed down.

@RCVideoReviews

2 жыл бұрын

Good tip.

Been flying flysky for a while now, when the weather let's me, I've watched this vid 3 times now and will watch it again tomorrow when my cross fire comes. It's easier to follow vids if you have tx16, crossfire, as every one uses them. 3 years of fighting with radio set ups. Hope this makes it eiser

@RCVideoReviews

2 жыл бұрын

Crossfire is a very good system--not perfect--but very good.

The intro music made me think of a chief John's video on how to cook something.

@RCVideoReviews

3 жыл бұрын

I've heard that a couple of times. I'll have to watch one of his videos to check it out.

Great video - very informative and well-paced.

@RCVideoReviews

3 жыл бұрын

Glad you enjoyed it!

Great job John well done looking forward to next video take care

@RCVideoReviews

3 жыл бұрын

Thanks Robert :)

Great video. I took a break also and I am changing my flysky gear over to crossfire and now I feel ok ordering it after watching your video.

@RCVideoReviews

2 жыл бұрын

Crossfire is excellent equipment.

Ola amigo, as traduções voltaram a funcionar estou estudando seus vídeos muito obrigado pelo seu trabalho. Aqui no Brasil indico sempre o seu canal. Aqui temos muito caras competentes no LR. Obrigado

@RCVideoReviews

3 жыл бұрын

Estou feliz por você ter descoberto e os vídeos podem ser úteis para você. Obrigado por referenciar pessoas ao meu canal. Gracias.

And to just add. A solid bind is also the blinking green on the module turns from blinking green to solid green

@RCVideoReviews

3 жыл бұрын

Yes. Thanks for clarifying.

Great vid, all my quads are on Crossfire with the TX16S. Another good feature for fpv is running smart audio from the vtx to the Crossfire Nano!!!

@RCVideoReviews

3 жыл бұрын

I have smart audio setup on my F722. That is such a nice feature.

@ab7rs

3 жыл бұрын

@@RCVideoReviews maybe a video on that....smart audio VTX control with crosfire and TX16S?

@reefercrazy1

3 жыл бұрын

what's the purpose of smart audio

@markb9896

3 жыл бұрын

@@reefercrazy1 smart audio is a communication protocol between the flight controller and the transmitter which allows, via your goggles, to change settings such as PIDs, vtx settings, etc.

@reefercrazy1

3 жыл бұрын

@@markb9896 I will go investigate this

I have had many issues with binding my Micro TX 2 with the Nano RXs. Had to contact TBS Support for fixes. I posted the 2 possible fixes that may help some stumbling across this video. Another tip. Make sure you have the latest Micro TX beta update installed via the TBS Agent.

@RCVideoReviews

3 жыл бұрын

Thanks for leaving the tips...I actually had to do this on my first one but it's because I unplugged it too soon which is why I put the callout in the video to leave it connected until the led goes solid green.

Great content and another great video. Thank you for explaining everything in great detail.

@RCVideoReviews

3 жыл бұрын

Glad you liked it!

Love the walkthrough. Thanks

@RCVideoReviews

3 жыл бұрын

Glad you enjoyed it!

Thanks for the walk through. Really helped.

@RCVideoReviews

3 жыл бұрын

Glad to hear it!

Really it's very much helpful. Thank you for your work.👍

@RCVideoReviews

3 жыл бұрын

You are most welcome

Great vid and overview. Thanks for the effort .

@RCVideoReviews

3 жыл бұрын

Glad it was helpful!

Great video as always 👍. Definitely going to save up for this addition to my new TX16S Max.

@RCVideoReviews

3 жыл бұрын

Good choice!

@AngryPepper1964

3 жыл бұрын

@@RCVideoReviews Great to know that, Thank you.🤟

Great video. Helps me a lot! Thanks man.

@RCVideoReviews

3 жыл бұрын

Glad to hear it!

Can't wait for my tx16s and cross fire nano kit to get here Monday ❤️. Thinking about taking a vacation day just so I can play with it early. And so it's not on my front porch all day, because my mail comes at 9 am

@RCVideoReviews

3 жыл бұрын

I would ;) Best thing about Crossfire is you'll never wonder about your RF link again.

@teourbs

3 жыл бұрын

@@RCVideoReviews I been debating it. Been watching alot of videos on it. I'm worried flying spektrum now without knowing my link quality is definitely scary. It's like a guessing game hoping not to go down and hunt for your quad. It gives me anxiety because I've almost lost a quad once from a failsafe.

@RCVideoReviews

3 жыл бұрын

@@teourbs Unfortunately, they aren't cheap. They're not terribly expensive either, but they're not cheap.

@mthompson3313

3 жыл бұрын

I got a nano, but it doesn't seem to fit the radiomaster tx16s

(EMERGENCY UPDATE FROM TBS SUPPORT) 1. power off the RX 2. hold the bind button on the RX 3. power on the RX 4. if green led is blinking very fast, hold the bind button again for 10 seconds 5. wait until the led turns solid red 6. power cycle the RX 7. rebind 8. resetup

@cognetic

3 жыл бұрын

@Mack Premo ?

@RCVideoReviews

3 жыл бұрын

Good tip...I did this on my first one.

Crossfire all day !!!

@RCVideoReviews

Жыл бұрын

Crossfire is a great RF tech. Glad to have it as an option.

Thanks Crossfire Micro is en route!

@RCVideoReviews

3 жыл бұрын

You're going to love it. When I fly with Crossfire I don't even think about my RC link.

Nice job...THANKS!!

@RCVideoReviews

Жыл бұрын

No problem 👍

Great video, very informative...

@RCVideoReviews

3 жыл бұрын

Thank you!

I made a coffee @8:45- 9:50 then some biscuits till 10:12 lol

@RCVideoReviews

3 жыл бұрын

I only let those run so people get an idea of how long it should take. Trying to offer a frame of reference.

SUPER vídeo tutorial 👍🔝🔝🔝🔝🔝

@RCVideoReviews

2 жыл бұрын

Thank you.

I'm in love with Matek products. Really not sure why.

@RCVideoReviews

3 жыл бұрын

They make a quality product as far as I'm concerned. I haven't found a fault yet.

Very informative, but do I need SBUS? What is SBUS for, can't i just fly when it's bound?

@RCVideoReviews

3 жыл бұрын

Crossfire receivers don't have PWM output unless you add special adapters. s.bus is what communicates between the Crossfire receiver and the plane.

I have a solid red light on the crossfire receiver. put the button but nothing is happening(its new never bind before just got the drone with the crossfire already install) thank you!

Hey pretty sure I know this but just in case All my rigs ( CrossFire ) can be bound to the single Model in the radio right . That's the way I had it in my Taranis. You shouldn't have to re bind every receiver to the radio right,

thanks!

@RCVideoReviews

Жыл бұрын

Welcome!

Also just to help you out. You do not need to use that bind button. You just go into the crossfire luascript and hit bind and it will detect the receiver update it and bind it automatically. When I learned that it made it so much easier to bind.

@RCVideoReviews

3 жыл бұрын

I thought the bind button had to be pressed on the initial pairing. I will try next time I get a new one without pressing the bind button. Thanks for the info.

Спасибо )) Thank You )))

@RCVideoReviews

2 жыл бұрын

You're quite welcome.

theres some nuance differences now in OpenTX July 2012 No Receiver No after selecting CRSF

I just got my TBS crossfire module. But I don't get those choices for binding. I get Tracer Micro TX, xf wifi, tracer nano tx, and Betaflight. I don't know what to choose. Bye the way, I admire all your videos.

Very good tuturial good job 👍👌🔝🇵🇹

@RCVideoReviews

3 жыл бұрын

Thanks! 😃

I bought this transmitter and receiver package and this video was perfect for me. Everything bound up exactly as instructed. But then I ordered more receivers and they won't bind. It says "Reload Crossfire FW". I can't seem to find any helpful videos. Any suggestions? Please help?

following along and have an AR wing working now with Crossfire and the TX16S, thank you. OpenTX is new to this former Spektrum user. Telemetry LUA is next.WHY did you switch from CRSF to SBUS??? Thanks.

@RCVideoReviews

3 жыл бұрын

I didn't switch from CRSF to s.bus permanently for any Crossfire RX that I use with iNav. ALL of my iNav FCs that have a Crossfire use CRSF.

Any possibility you could modernize this? None of my menus look anything like this after I updated to the latest firmware.

So I’ve got 2x nano Xf I have done the reset and repair process and get the green light to bind on both as soon as I hit bind the nano flashes red and tango 2 say connect agent x I do this and nothing. No bind just flashing red light. It doesn’t even let me update anything? So then I reset it again and all looks good but it’s just a viscous circle of disappointment and broken promises. Please help 😉🤘🏾🔥

After the firmware updates it says binding but then never binds.... The green LED is flashing very quickly

@RCVideoReviews

3 жыл бұрын

You need to look for the Crossfire Green Flashing Light recovery process. Something went wrong and the only way to solve it is to run through that recovery process. Have no fear though--it works just fine. You can't brick Crossfire Rxs.

Just in case others are here because they can't get the module to work, make sure your pins are lining up from the radio to the module. I had to bend mine a considerable amount to line them up and thought I had a dead module.

@RCVideoReviews

3 жыл бұрын

Good tip. Thanks for sharing. 100% agree.

What difference does it switching to sbus instead of leaving csfr?

@RCVideoReviews

3 жыл бұрын

CRSF supports two way comms and theoretically has lower latency. I would use it given the option.

Is the lua script pre installed on the radiomaster or do you need to dl that on a SD card first.. I m asking cuz im thinking about the buy the radiomaster boxer

After I switch the external RF over to crossfire for some reason I do not see the receiver option to even pick a receiver number. Can you tell me why?? Also whenever I go to bind the crossfire, after choosing bind it just sits there and says binding. It doesn't go into updating mode for some reason .. something is going wrong.. Lastly while I'm binding mode if I press the green button on the back of the crossfire only then will I see binding ok but when I go back to Setup Nano tx doesn't appear. Smh I'm having issues at each step

Can someone, anyone do this exact same set up video for this same crossfire module, but for the Radiomaster Boxer? I'm really struggling to get my new Bind n Fly set up. I've bound my goggles and 03 air unit, but I have a boxer and crossfire module and don't know where to go from here. Really want to get up in the air?

To clarify my thoughts, If I'm buying the Explorer LR 4 V2 HD Micro Long Range FPV with an option for the TBS Crossfire Nano RX, do I just need to purchase the Crossfire Module and Antenna for the Radiomaster TX16s? Thanks!

@RCVideoReviews

2 жыл бұрын

Yup. Sounds right to me.

Will this be a similar process for setting up the radiomaster boxer and crossfire module? I bought a bind n fly Bob57. I planned on getting tbs Tango 2 but they’re literally not available anywhere so I ended up buying the radio master Boxer and the crossfire module. I’m a complete newb so it’s all truly confusing.

@RCVideoReviews

Жыл бұрын

Yes, the crossfire module configuration will be very similar on the Boxer. It will look a little different being a B&W screen of course, but the process will be the same.

what model and where did you get your sbus meter?

will this fit in the jumper t18 pro?

@RCVideoReviews

2 жыл бұрын

The TBS Crossfire external module? Yes it will.

Hello helpful video...can u bind a nano Rx to a micro transmitter or vice versa and so on since they're from the same company?

@RCVideoReviews

3 жыл бұрын

I don't have first hand experience doing it, but I would expect the answer to be yes. You may have to contact TBS for a precise answer.

HI, if your quad is CRF BNF, do you need to select SBUS OUTPUT as you do in the TR16S settings ? I don't understand why changing CRF to SBUS if your TX and RX are CRF please. ( I'm about to receive my tiny whoop CRF quad in the next hours ! )

@RCVideoReviews

3 жыл бұрын

It depends on the flight controller. If your flight controller can use CRSF then use it. If it can't (many can't) then you need to use sbus. Think of CRSF and SBUS as multi-channel/single wire. It's not the RX and TX you need to worry about, it's the RX and the FC that both need to speak SBUS or CRSF.

I just got my crsf xt module and followed all the steps, for my Radiomaster tx16s , when i press discover all sensors, i only get 10, no rxbt, Curr, CaPa, or Bat_ any ideas what is not correct, have all the current updates.

@RCVideoReviews

3 жыл бұрын

I don't know why they show Curr/Capa as options. I don't know how to get current readings from a straight BEC connection. I believe that has to come from a FC or some other device with a current sensor. Power supply monitoring is only good up to 2s LiPo but that should show up. There's a note in the manual to select Ignore Instances if sensors are missing. It might be worth a try??

Great video, but I am unfamiliar with the ToolkitRC monitor that you are using. What is it used for and how much can it do? Thanks. - Jim

@RCVideoReviews

3 жыл бұрын

This should answer most of your questions: kzread.info/dash/bejne/ppacs7Rrpte2qs4.html

Well.. I did not see You pressing that tiny button on the receiver for crossfire at any point as You mentioned in the beginning of the video and You still have bind those without any issue.. Did You forget to put show this in Your video or it was not necessary than?>

@RCVideoReviews

3 жыл бұрын

I've had feedback from some that the button press isn't required. I had already bound this receiver in prep for the video.

@VictorSeedorsky

3 жыл бұрын

@@RCVideoReviews that's not quite true as in my case (both Nani receiver and tx micro V2 brand new) nothing has happened when I pressed "bind" on the tx.. and Rx was just red light stand still for ever. I than had to unscrew my long range drone too cover and thanks to your video localise where that tiny button is and depress it so it could find eachother with tx and update aromatically. What sort of range on this setup should I get with T-immortal antennas?? I recon it is not going to be more than 4km? Definitely not (up to) 40km as they advertise this.. and on what power ?

@RCVideoReviews

3 жыл бұрын

@@VictorSeedorsky I never tried binding without pressing the button which is why I qualified the comment. I haven't flown it out of range and given the state of governance these days I wouldn't be willing to say how far I have flown it. It's one of those things you'll need to test.

What is the difference in choosing sbus or crsf? Why choose one or the other?

@RCVideoReviews

2 жыл бұрын

Crossfire is bidirectional. Sbus is not.

Nice one👍 but I have updated my and tx module now all my binding in all quads have gone. Its solid red and pain to reach the bind button on the rx. Is there anyother way to get the rx into bind mode without pressing bind button?

@RCVideoReviews

3 жыл бұрын

Did you try just powering on the Rx and using the bind option on the Tx in Agent lite?

What is the exact distance of the remote? TX16s

Have u used this setup with tbs unify pro32 hv connected to RX then to FC?

@RCVideoReviews

2 жыл бұрын

I have not.

What's the maximum power out supported on this radio? Does it do 2 watts fine on the crossfire or is that dependant on the battery?

@RCVideoReviews

3 жыл бұрын

Crossfire says 2w: www.team-blacksheep.com/products/prod:crossfire_micro_tx I haven't set it manually to 2w to test.

hi I was wondering how do I fix the module when it is stuck in boot loader mode my pc turned off when I was about to update the module v2 and now it is only in boot loader mode and flashes green is there a way to fix this 😒

@RCVideoReviews

2 жыл бұрын

I know the Rx has an emergency mode recovery. Have you checked with TBS?

When I go in the Tool section on my radiomaster TX16S I don't see the crossfire configure menu. How do I get it?

@RCVideoReviews

3 жыл бұрын

You have to install the Crossfire LUA if it's not there.

@Synexed

3 жыл бұрын

@@RCVideoReviews I did that and it worked, thanks :)

Hi there - can you provide a link to the next video you refer to in this video?

@RCVideoReviews

3 жыл бұрын

It was this one: kzread.info/dash/bejne/fWx_vNOklJWfoso.html

@iancurry8504

3 жыл бұрын

@@RCVideoReviews Thank you

Hi, will this tutorial also work for the Radiomaster TX12? Cheers in advance

@RCVideoReviews

2 жыл бұрын

It should

Very informative. Question for you I just switched from the taranis x9d to the radiomaster t16s with the full Crossfire module. I have been having trouble with the transmit power only outputting 2 milliwatts. No matter what I set the output power to on the crossfire module it would not transmit more than 2 milliwatts. And was getting critical RSSI warnings only ten feet away. So I deleted all sensors on the radiomaster and reclicked discover new sensors. And was finally getting the proper transmit power. But I lost other Telemetry sensors like current and Kappa, along with a few other sensors. Basically I just had RSSI centers and no longer had battery voltage current traffic and a few other ones. Why did I lose the actual flight controller Telemetry data?

@RCVideoReviews

3 жыл бұрын

Can you delete and re-add those sensors on your Taranis? I would re-bind with Taranis and see if you can remove and re-add. If you can, then you may be facing some software issues. I.e. Get latest OpenTx, get latest lua, get latest crossfire firmware. I know with the iNav scripts it just works straight up.

@fpvandgasrc4321

3 жыл бұрын

@@RCVideoReviews everything works on my taranis,,i havve all my normal telemtry, but on the radiomaster i dont

@RCVideoReviews

3 жыл бұрын

@@fpvandgasrc4321 Did you delete and re-add the sensors on Taranis?

happa family anyone?

menu is way different.. for the tx16s. I have like 3 pages of lua script, no crossfire setup or at least no abbreviation i understand as crossfire

@RCVideoReviews

Ай бұрын

You can manage tools elements with the scripts in /scripts/tools TBS Crossfire lua has to be installed. Google is your friend.

@JeSSTeR81

Ай бұрын

@@RCVideoReviews It has been a mission for sure… I got the new Cinabot30 and new Radio master, so it seems hard to find any that are the same layout or connecting the actual same drone … even though it’s supposed to be ready o fly

@JeSSTeR81

Ай бұрын

@@RCVideoReviewswill not bind

Need guidance!!i have the tx16 se version and want to install this same module..if i get a whoop with crossfire receiver do i have to follow this same steps?or its just bind and fly.

@RCVideoReviews

3 жыл бұрын

I'm sure you can bind and fly, although I can't say for certain because I've never used anything with Crossfire but a standard Nano Rx which I always bind. In any case, it's not hard to pair and go.

@BTOACORDEONES

3 жыл бұрын

@@RCVideoReviews also i was looking at the tango 2 with built in crossfire any advise wich one do i need?in.order to bind to betafpv85x crossfire receiver.thanks

@RCVideoReviews

3 жыл бұрын

@@BTOACORDEONES If you don't get the Tango 2, and you want to use Crossfire, you'll need to buy a Crossfire module. So if that's the plan, you may as well go with the T2.

So I know someone else has probably asked this, but what range could I expect out of one of these? Miles or feet?

@RCVideoReviews

3 жыл бұрын

Miles...15+

when i bind my nano with the micro it's just stuck at 0% what should i do?

@RCVideoReviews

3 жыл бұрын

How do you know it's bound?

@stealthy8206

3 жыл бұрын

@@RCVideoReviews nevermind it worked it just took 2-3mins longrr but thank you

Hi ! Can I use a Naza lite with TBS Crossfire ?

@RCVideoReviews

Жыл бұрын

If Naza takes sbus you can.

If im faster than i listen first... How can i Change the countrycode again to Open ?

@RCVideoReviews

3 жыл бұрын

Ohhh...you may have to contact TBS. I don't think there's a way to do that. That might be a factory only option.

@sebastianwinkelstein7213

3 жыл бұрын

@@RCVideoReviews thanks for Help, i have found this -) and it Works :)Regular CROSSFIRE TX: In case you want to un-lock your TBS CROSSFIRE you have to enter the Konami Code. Power up your TBS Crossfire wait until you see the main screen then do the Joystick combination "up, up, down, down, left, right, left, right, enter enter". Got to the "Menu" -> "General" and you should see a new selection called "Region". Select "Open" to unlock your TBS CROSSFIRE.

just got this set and dont just realize that its for quads, and i have wing :( and no fc, so i can fly now?

@RCVideoReviews

3 жыл бұрын

It's not just for quads. It's a Transmitter/Receiver combo. It can be used for any type of RC model; however, as the nano rx has no pwm/power out, you need to find a way to drive your servos. Look into any basic stabilizer that supports s.bus. iStone stabilizers from Detrum work well with s.bus.

Thanks for video and i hope you can help, i've been flying my wing about a month with crossfire micro tx v2 and nano receiver couple days ago I swapped out the nano with a new nano due to range didn't seem as good as it should be, now i'm missing some sensor data in my radiomaster tx16s, radio shows all sensors i think 22 but gps,gps speed,alt. and battery percent all missing, i've tried deleting and rediscovering but still no data. when connected to laptop inav is showing good 18 sat. and gps location, i've updated the tx and rx using crossfire companion. I've also been in radio sensor page trying to change settings on these sensors which has maybe made it worst. my opentx is 2.3.9 and inav is 2.5.0. i've even tried the first nano but same results. what am I missing? Any help would be great Thanks again

@RCVideoReviews

3 жыл бұрын

That's definitely a strange problem. You had data, switched RXs, lost data, switched back, still lost data. I'm not sure where to go with that one. Did you make any iNav changes? Did you change any firmware in the middle of all of this? If I were in your shoes, I'd probably save my iNav config, do a full reset, configure crossfire in iNav, create a new model, bind, and discover sensors. i.e. I'd strip it down to fresh and very basic to see if I could get it back, then I'd go from there. That's a tough problem.

@egtreadway4232

3 жыл бұрын

I only updated the nano wirelessly after I wired it up and bind, I do notice sometimes when I power up nano that I have a green solid light and radio not even on yet I then have to click bind button on tx I'm wondering if this is related to my sensors problem? Thanks

Do I have to have that equipment where you plugged in the receiver?

@RCVideoReviews

3 жыл бұрын

Can you give me a time index so I can see the equipment to which you refer?

@Zionson1

3 жыл бұрын

@@RCVideoReviews 8:33

Will the Tbs tracer work in radio master TX 16s ?

@RCVideoReviews

3 жыл бұрын

Yup: www.team-blacksheep.com/products/prod:tracer_starterset

Is it easy to use crissfire whit dx 9 System?

@RCVideoReviews

2 жыл бұрын

Sorry I don’t have the first clue about Spektrum. I don’t own any of their equipment.

Are the red circles optional? Like the kit with all the red parts?

@RCVideoReviews

3 жыл бұрын

I'm not sure what red circles you're referring to.

@chrisscotty4518

3 жыл бұрын

I dont know what is it called....the red circles around the gimbles

@RCVideoReviews

3 жыл бұрын

@@chrisscotty4518 Those are 3d printed gimbal spacers. If you buy the CNC upgrade kit, that comes with CNC gimbal spacers if you want to use them.

@chrisscotty4518

3 жыл бұрын

Ok thanks....i have the radioking tx18s so i dont think they will fit

@RCVideoReviews

3 жыл бұрын

@@chrisscotty4518 They won't. Jumper T18 gimbal spacers might though.

I have no idea what i am doing wrong but i have extremely reduced range in my crsf setup.... like 10 metres and fail safe. Any suggestions?

@RCVideoReviews

3 жыл бұрын

There are dozens of possibilities. Based on that short of a distance I would guess bad antenna or antenna connection to rx.

@baruahaleen

3 жыл бұрын

@@RCVideoReviews nah…. All the basics like that i have checked 10 times till now

@RCVideoReviews

3 жыл бұрын

Change Rx, change antenna, check Rx voltage, check Tx power level, ensure no "lower power mode" is enabled on radio. Other than that, you're into hardware.

@baruahaleen

3 жыл бұрын

@@RCVideoReviews got it... thanks for the tip... much appreciated

@RCVideoReviews

3 жыл бұрын

What was it?

Hey is this the same as edgetx?

@RCVideoReviews

Жыл бұрын

Yup

Hi ..Nice video.. just subbed.. can you tell me the model number of the toolkit RC you are using please.. I am also trying to set up my crossfire v2 micro. thanks.

@RCVideoReviews

2 жыл бұрын

That’s an M8s. Excellent charger and bench tool.

@COZ-1973

2 жыл бұрын

@@RCVideoReviews Much appreciated.

Is this the erls or 4-1 tx16s version?

@RCVideoReviews

11 ай бұрын

This particular radio was a 4in1 version, but it doesn't much matter because this process requires an external TBS crossfire module.

@Marc_FPV_

11 ай бұрын

@@RCVideoReviews so I can use the erls version with the external tbs module right?

is this the same as new tbs tracer micro tx starter set .

@RCVideoReviews

3 жыл бұрын

No, this is the 915mhz system.

what is the max range with this setup?

@RCVideoReviews

3 жыл бұрын

I've never flown it to range so I can't give you a number based on experience. Their marketing says up to 40km.

can i use nano without fc??

@RCVideoReviews

3 жыл бұрын

Only if you provide an alternate method of driving the servos like an sbus adapter. There are no PWM or power output rails on the nano.

@dankhalifa6937

3 жыл бұрын

@@RCVideoReviews hello i got tbs pwm 6ch and only thing working is motor, servos dont work on None channel:(

Is there a way to reset the region setting ? Idiot me was to fast and ngl germany has shitty regulations

@RCVideoReviews

2 жыл бұрын

I don’t think so. You might contact TBS to see if they can help.

@MrLemurenAffe

2 жыл бұрын

@@RCVideoReviews found a way While in crossfire settings push the button on the modul 10 times fast

whts the point of using crossfire when u lrdy have the elrs ? makes no sense

@RCVideoReviews

10 ай бұрын

Maybe check the data on the video...?

Every time after it updates it goes to Reload Crossfire FW, then after a couple seconds it sits on Bind

@RCVideoReviews

3 жыл бұрын

What is the led doing when this happens?

You are just too early I just bought the TBS Tracer micro TX starters kit.

@RCVideoReviews

3 жыл бұрын

I know a bunch of new 2.4 options just hit. This will serve my purposes though :)

@fpvlive

3 жыл бұрын

@@RCVideoReviews Yes in your use case Crossfire is a really smart choice, Thanks again for the nice conversation we had on your channel !

@SacredMilkOG

3 жыл бұрын

Right? I just ordered one of these setups and then discovered a whole new line of tech is dropping. Meh... it's a good start.

your the best... today.. hugs and kisses

@RCVideoReviews

3 жыл бұрын

Ok...Thank you.

I jumped the gun for Bardwell tells us all the Jumper T16 Pro is his new daily driver, well so I got one last time I listen to his BS about his new daily driver forever ON ANYTHING! For NOW naturally, after I went through the

@RCVideoReviews

3 жыл бұрын

I think you got cut off.

@TheTurbo930

3 жыл бұрын

@@RCVideoReviews yes I did let me try again....my short novel...sort of a RANT....Bardwell BS.... lol...... OKAY... I jumped the gun for Bardwell tells us all the Jumper T16 Pro is his new daily driver, well so I got one last time I listen to his BS about his new daily driver forever ON ANYTHING! For NOW naturally, after I went through the "STUCK KEYS" BS but did in fact get it back right!>? Thing is NOW NATURALLY Jumper and this NEW Ranger spin off do their little things to improve the Jumper T16 Pro like everything is not PC cable to EVERYTHING in the radio as well as some parts are now metal not the plastic, and the thing that REALLY PISSES ME OFF JOSHUA is you can get the best Radiomaster T16 CHEAPTER than what I paid for my JUMPER T16 Pro!! Anyhoo It seems to work fine now I have only set up one D16 FrSky so far and have the R9M TX and don't even know if it will work with the Jumper always assumed it would but had it on my Taranis X9D Plus and am scared to even try, so my question is will one of the Crossfire modules work with the Jumper T16 Pro as should?? I cannot find ONE NOT ONE MR DAILY DRIVER that tells you the R9M or CRSF either will work with it, but as said when I purchased the damn thing JOSH I thought well there ya go! I'll have every protocol I want and need with the built in multi unit and a bay for my CRSF so NOW PLEASE DONT TELL ME THAT IS WRONG??!! I'd hate to beat up Bardwell and take his Radiomaster and Tango 2 Pro and leave him for dead!!?"?-THX, Turbo.......lol hahaha lol BUT FOR REAL! I'm not listening to ANYONES BS about what their "NEW BADASS ONLY WAY TO GO SET UP" is for Christs sake for THEIR LYING PERIOD!! they make a new damn model every two months on this cheap crap, reason if you tell me the Jumper pro won't work for this going to simply get the Tango Pro2 and have my Crossfire built in my its maker nothing better and costs close to the module if you want the big boy knowing the micro is what $69?? So worth the money and $120 with Three RX's and antenna to boot! SO either way I think if there's anymore nonsense about it I'll get the Tango Pro 2 It's badass!! hahaha Hope this isn't a short novel I JUST WANTED YOU TO FEEL MY PAIN!! lol haha For Of course YOU are using the Radiomaster Jumper copy.....lol yep,,.. Well Thanks great video and PLEASE let me know if the modules work fine as intended I thought with the Jumper, even the R9M! I might use it if Josh wouldn't have said, " The R9 system works only with FrSky Radios" yes he did, so he has me totally confused on taking his advice on getting his NEW DAILY DRIVER.......The sell out... Thanks Good video and I think if I follow your instruction on the Radiomaster it will be fine!! Let me know if any more tips in that respect....THX Sincerely, Turbo.

@TheTurbo930

3 жыл бұрын

BUT HERE IS MY MAIN QUESTION?? EVEN THOUGH I'm REALLY and prob not only one of hearing sell out's and their BS!!. Thank you please let me know if JOSH JACKED ME or I got what I thought I was getting.....I'm about to have a cornery.....lol UWill the TBS modules work with the Jumper T16 Pro?? For it looks exactly the same as the Radiomaster, and I'm gathering that is where it derived from....Which makes me angry for the RadioMaster is cheaper than what I paid for my Jumper Pro..... anyway, will the module work with it as well as the R9M module for Bardwell says in a video that the R9 stuff only works on FrSky?? Is that so as well? Thanks great vid, just hoping it works same for my Jumper T16 Pro. I'm a little late on the CRSF as well, tried the much cheaper R9M and worked quite well, but really want the crossfire! Thanks again-Turbo. Will the TBS modules work with the Jumper T16 Pro?? For it looks exactly the same as the Radiomaster, and I'm gathering that is where it derived from....Which makes me angry for the RadioMaster is cheaper than what I paid for my Jumper Pro..... anyway, will the module work with it as well as the R9M module for Bardwell says in a video that the R9 stuff only works on FrSky?? Is that so as well? Thanks great vid, just hoping it works same for my Jumper T16 Pro. I'm a little late on the CRSF as well, tried the much cheaper R9M and worked quite well, but really want the crossfire! Thanks again-Turbo.

@RCVideoReviews

3 жыл бұрын

Ok, that was a bit of a tear and hard to follow. Here's what I can say: 1) I use Radiomaster exclusively. While I've had one switch fail and RM took care of me very quickly, I've had no other failures. 2) I use Crossfire for most of my FPV setups. My first Crossfire TX lost its wifi module for some reason, but was still able to bind with Crossfire RXs--I wasn't comfortable with that, so I replaced it with another Crossfire TX. My main FPV setup then is Radiomaster TX16s and Crossfire. I've had two minor issues with them, but otherwise they've been solid. I seriously do not believe Josh "jacked" you. You have to understand as reviewers, we can only see what is in front of us, not what is in the future. I'm sure his review of the T16 was as accurate as he could make it the day he did it. It's really not fair to hold him accountable for a failure not evident on day one. I've watched a number of his videos and while I don't always see eye to eye with him, I don't believe for one second that he's a sellout or trying to be deceptive. Hope that helps