How to assemble the Novara Chrome Round Glass Dining Table from Furniturebox UK
Тәжірибелік нұсқаулар және стиль
We have put together this step-by-step guide for how to assemble your Novara Round dining table. This guide can be used for the 100cm and 120cm size dining table. There will also be a printed assembly guide in your package to help you put this dining table together. Please carefully read the safety advice. We recommend using 2 people to assemble the Novara Table. You can pause the video at each stage as you follow along with the video.
Пікірлер: 41
I've honest to god never seen such an awkward way to put the legs together while providing fuck all in the manual on how to line them up properly, instead I'm stuck watching a 2 sec clip at 0.25 speed trying to figure out what's going on that's equally unhelpful
Okay sixty something woman here assembled dining set single handedly. I fixed 2 legs loosely to the square middle piece (only 1 screw & not 2 as shown). Attached legs to table top then added the remaining 2 legs. Super pleased with result!! Partner will not believe I did it without him 😂
@janelleguiste-burrows7140
Жыл бұрын
I was struggling, then saw your comment & followed! Thank you soo much! X
@omolola1044
13 күн бұрын
Thank you!!!! I can’t believe i just put the table up with this technique of yours.
Urggh, I guess the reason you're here is because you found the manual so helpful, lol. Everything is pretty much easy and straightforward until you get to the damn middle section where you have to join all the legs together. Even worse when you're doing it alone like I was. My table was a 100cm one with gold legs and only 1 whole on the legs instead of 2 as shown on this video) After many attempts and almost breaking the glass, I finally found an easier way. I noticed that when you have all the legs fitted onto the table top, it's difficult finding where the middle of the table is. So it seems like the legs can never connect altogether. What I did was remove 3 legs and left one connected to the table (made sure to leave the nuts right next to each whole on the table to make it easier when reconnecting back). On the side, I connected 2 of the OPPOSITE legs to the plate. That way, you're already half way there and 2 is less heavy than 3. Then carefully balance the two legs on the plate and screw them loosely to the table top but tight enough not to fall. The third leg (one that's already connected to the table) should be able to connect easily (now you've found the middle). Then finally connect the 4th leg. It will seem difficult at first but as you play around with the plate and other legs (lift, shit left and right) and you'll find the hole to the 4th leg. I hope this is helpful to anyone struggling with connect the plate to the legs while all legs are connected to the table.
@skylerlewis7821
Жыл бұрын
Omg you don’t know how much this comment means to me, been trying to fit mine together for almost 3 weeks. Was even about to contact seller about changing the item or something x
@skylerlewis7821
Жыл бұрын
❤❤❤
@lf6111
10 ай бұрын
This comment was a lifesaver and honestly better than the video! Thank you!
@WillOnChill22
Ай бұрын
You saved my life with this
Ok the middle section is different from the one shown (4 screws not 8). But the secret is to fix the legs together loosely before you fix to the glass top. Once together tighten everything up. Easy to do on your own this way.
I bought this Novara table and four chairs , Very attractive furniture.chairs were easy to assemble , but table was difficult, After watching this video It was so easy. THanks Furniture Box. Customer service was very helpful and they even replace one of the table leg , its part broke during first attempt, Many thanks Pete. I will be buying few things for the house .
@xIHEXx
2 жыл бұрын
Was your middle piece different ? Only has 4 hole screws..
@blessingjinga4776
Жыл бұрын
Amazing, this is the only thing that actually helped! Thank you
good job
After spending hours trying to fix the legs to the square centre plate. The video was no help. I found a comment which said...Fix 1 leg at a time to the plate, work clockwise to fix the others..It worked!!!
Just purchased this and I’m stuck. Any tips you can give I will be very grateful. Thanks
Our legs and middle plate do not aligned. Weve spent way too much time trying to figure this out. Need the company to reach out to me.
Went through all of the comments hoping someone might have the same issue as mine. What if the round disc comes off from the glass, how can we attach it back to the glass?
the middle plate is different and i have been sitting with the table undone for the past weeks. i have no one to help me and i don't get it why they made the screws for the middle plate so short
Where can I find person to fix my table leg ?
This vid did help as the manual was rubbish.. Had to watch the vid real slow but got there
I couldn’t of done it without this video Thank you thank you thank you
my screws were lost upon delivery and i don't wanna send it back the seller want respond can the screws be bought from home depo
Can someone please help me!!😢 I’ve been at the legs since last night and still can’t get it… is it just me or is this just so complicated lol
I found the easiest way for me is to install the opposite legs into middle piece first then install it to the table that way you can install the remaining two legs easily
After spending 6 hours I have concluded I have been sent faulty legs/middle plate which do NOT align. - wish i read the comments before purchasing 😭
DO ONE LEG AT A TIME! Connect one at a time to the center piece then add the others….
Is anyone still clueless after watching this video? Having a hard time setting up the legs
@garyw1971
2 жыл бұрын
Did you work it out? I'm here scratching my head.. the middle support is different !!!
@ganeshs1783
2 жыл бұрын
@@garyw1971 yeah we tried differently, join the legs and the middle support first separately and then adjust and fit it to glass
@steevie8001
2 жыл бұрын
@@garyw1971 same here mate the middle plate is different and doesn't line up with all of the holes 🤷♂️
@xIHEXx
2 жыл бұрын
Anyone figure this out ?...
@xIHEXx
2 жыл бұрын
With the middle holes being different... ?
Like why make the video so fast?
I’m frustrated b/c the legs should be labeled for a better assembly!
After 3 hours trying to figure out how this shit work, i made it. This is the worst instruction ive ever seen. You cant even see anything how they move it in which direction its too fast. Bad Review for sure.