How To Apply WaterSlide Decals
Ойын-сауық
Mark Kirk Show Us How To Apply WaterSlide Decals
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▶For any business inquiries please contact us at: gunplanetworkinfo@gmail.com
▶Check Out The BEST Gunpla News: • Gunpla News: GM Guard,...
▶MG Reviews: / watch
v=xv5rRVC5CD8&list=PLGGZ5BSUuePI7AvN2Y0_FO8-gIlv8ywCA
▶HG Reviews: • HG 1/144 AGE-3 Normal ...
▶RG Reviews: • RG 1/144 RX-78-2 Gunda...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
▶Get Your Official Merchs: teespring.com/stores/gunpla-n...
▶Join Us On Facebook: / gunplanetwork
▶Check Out our Instagram: / gunplanetwork
▶For All The Latest News:
www.gunplanetwork.com
#gunpla #plamo #gundam
Music By Kijugo
• golden wind (Jojo but ...
Пікірлер: 34
1. Cut out the decal and dip it in warm water for 5 seconds 2. Take it out and sit it on a paper towel 3. Get some setter and put a drop where you want the decal 4. Slide the decal off the paper and position over the setter 5. Use a cotton bud and roll it over the surface to remove the excess setter 6. Let dry for 5-10 Mins and then brush a small amount of softer over the decal 7. Don’t touch it even if the decal gets wrinkled 8. Let it dry naturally
@BigGun1911
Жыл бұрын
I’ve never done anything like this but em going to try it out with the Marvel Legends Target exclusive Thor Ragnarok. His eyes are red and want to paint them white and add water decal eyes.
@nopparat6388
Жыл бұрын
Excus me i dont have setter (because the money is gone)
@markkirk7305
Жыл бұрын
@z.1306 it helps if it is stuck to the paper warm gets it off
@artyourself-qz9pv
11 ай бұрын
Thank you
@No1PepsiFansProductions
6 ай бұрын
But does the decal et sealed to the model to the point where it looks like it's part of the plastic
This vid was a lot more helpful than the instructions that came with my Gundam. Thanks! Short and straight to the point with some chill music.
It's a Gundam!
Cool, These are the exact two solutions that i was wondering if i can use together. thank you!
Is it better to remove top coat first before applying WSD? I already applied Matte Finish but I am planning on adding some decals on my kit
I mean i wish I knew what the other 2 products used were .
@markkirk7305
2 жыл бұрын
WhIch ones man? Mark fit by tamiya / or mr mark setter Mr mark softer Water
is it necessary to apply mark fit and mark softer?
so setter bonds while softer makes decals flushed?
@awesomeguy7624
2 жыл бұрын
Well the softer is meant to sorta melt it so it can better adhere to curves and go into pannel lines whilst bond is a glue to keep it there
@markkirk7305
2 жыл бұрын
Yeah pretty much man
After the decal dries, is it scratch proof like the ones on barbie's eyes?🤔(I know it's not 100% scratch proof, but it's not easily removed either with one scratch😂)
Do you have to seal it? New to this all btw
Could I also use Mr mark setter
Do you need to water for it to completely dry before applying the final seal?
@DarkTetsu
Жыл бұрын
I would let it dry in order to seal properly. Water can’t evaporate through a top coat.
What would you do if you don't have the setter
@DarkTetsu
Жыл бұрын
You don’t need the setter. It’s only if you want to melt the decal around a curve or eat the clear portion of the water slide.
@Truck-kun_01
Жыл бұрын
@@DarkTetsu it might've been a year too late, but your advice will always be appreciated. kind stranger
Is it better to topcoat before or after applying water slides?
@GunplaNetwork
2 жыл бұрын
After to seal them
@markkirk7305
2 жыл бұрын
If the kit isn’t something super shiny or special surface I use it before and after
Is no one gunna talk about how criminal this beat is? Straight iller than hamburger filler.
No top coat????
@zawiahtengah5374
Жыл бұрын
it