Good instructions mate for a quick tighten, worth noting there is a more effective/proper way to adjust gen 3 and 4 handbrake. Need to jack up the entire rear of the vehicle, put on jack stands for safety :) chock front wheels and take out of gear and release the handbrake. Loosen off the adjuster under the console. There is an adjuster on either side of the vehicle, accessed from the bottom of the hub assembly, wheels may need to come off to assist in accessing. Tightening up both sides evenly, testing the number of clicks now and then to check. 5-7 clicks is what the Mitsubishi service guide says is the desired number of clicks. You can then use the front adjuster under the console for your next adjustment when required, as it has now been loosened off a bit. Some things to note. The Pajero uses drum/shoe style for the handbrake, and disks for pedal brake. Due to this, crud/rust/etc can build up inside the rotor where the shoes clamp to stop the vehicle moving when the handbrake is applied. This build up can decrease the efficiency of the hand brake. An old trick to help keep drums and shoes free of build up is to occasionally apply the handbrake lightly when driving along at around 40kmph. If the shoes are getting worn/low, that would also mean the handbrake adjuster needs tightening, if overtightened it will stretch the cable also, so be careful not to over do it. The rear will have a set of pads and a set of shoes each side. Edit: great tip about applying the hand brake on an auto or CVT vehicle before putting it in park, takes the stress off the transmission when parked on a hill. I do this in my wife's car always, not as important in a manual though.

@budget4x4life

Жыл бұрын

Thanks a lot for this info mate it certainly is the proper way to do it💯 I have pinned it so other people can see this as well thanks for your input I appreciate it and sure others will do too🙂🙌🏼

@tongyspaj

Жыл бұрын

Yeah I need to get around to doing this since the tightener in the cab ain’t doing the trick, just been too bloody lazy haha

@pajlife

Жыл бұрын

@@tongyspaj I need to do mine too. Waiting until I install my new rotors and pads though.

Mate,cheers for the awsome tutorial.Was short & sweet & had my hand break back to operating like a treat. Thanks mate.

@budget4x4life

Жыл бұрын

Awesome Travis glad I could help💯😜

Awesome! I've got a mean video idea which I havent seen around but I've seen the process suggested a tonne. The left rear hub nut apparently come loose on these - causing some shudder/clunking through the driveline etc. You have to jack it up and get someone to hold the brakes, and then tighten it to spec with a torque wrench OR absolutely hang off it - needs to be TIGHT. Would be sick to see a how to video for this! Cheers, Alwyn

@budget4x4life

Жыл бұрын

Haha cheers Alwyn. My dad used to do it all the time on his paj😄 He used a moerse lang pyp and put all his weight on it to make it tight💯 but unfortunately happens again after a few months haha

Wonderful and Helpful Video Mate!

@budget4x4life

Жыл бұрын

You're welcome😊💯 Thanks for the support 🙌🏼

@mrfrenchman8289

Жыл бұрын

@@budget4x4life Your Welcome 🤗

@sfcralogan

Жыл бұрын

Have tried this before, it worked for awhile but now it’s worse than it was before, virtually zero handbrake. Not sure now if I need new pads or adjustment at the rear drums.

@budget4x4life

Жыл бұрын

@@sfcralogan Id go for adjustment in the rear if it requires a lot of adjustment. Check your pads and drums. It might need a clean out 💯

Thanks bro 👍

@budget4x4life

Жыл бұрын

No worries 😊💯

Mate !!! Just done it thanks heaps mine was flogged ! 🤣 that was easy as

@budget4x4life

Жыл бұрын

Haha no worries mate glad I could help🤣💯🏅

Thanks

@budget4x4life

6 ай бұрын

No worries 🔥

Awesome bro

@budget4x4life

Жыл бұрын

🙌🏼💯😎😄

Hey boet: have you ever considered installing interior foot well lights that have the option to change colours? This is very cool

@budget4x4life

Жыл бұрын

Hey Leon😎 Haha I had it in two of my cars now and it was cool. Especially when you sync it with the music 😄 Think I got a bit over it now and want the Paj to look clean on the inside. However the video dropping today will be the same thing but for the outside 🤣

Great wee video mate. Got a question for you, does the swb model have a headlight height leveling sensor on the back passenger side just at the upper suspension arm if so have you got a picture and the length of the connector bar as on my LWB model my connecting is missing and looking for a measurement for it. TIA

@budget4x4life

Жыл бұрын

Hey Gordon, please message me via Facebook messenger. My page name is Budget 4x4 Life. If you can send me a photo of the part you need I can have a look🙂💯

Thanks bro 👍 just quick one could you please share tire details and confirm what type of lift kit installed on your pajero ? thanks in advance.

@budget4x4life

Жыл бұрын

No worries 🙂💯 275 65 18 Falken Wilpeak at3 tyres 2 inch West Coast Suspensions lift kit

@helloweekend

Жыл бұрын

@@budget4x4life thanks for prompt response mate. it is much appreciated.

@budget4x4life

Жыл бұрын

@@helloweekend no problem 😜

Easy peasy 🍋 squeasy⁉️😊 Gotta luv the Shorty right❣️😆

@budget4x4life

Жыл бұрын

😄😄 Yess definitely love it mate!!🔥😜

@tightatours

Жыл бұрын

@@budget4x4life I just fitted a XROX Bullbar on Shorty n love 😻🤟it… on KZread soon if like to take a look?? Your clips have helped heaps thanks 👍

@budget4x4life

Жыл бұрын

@Around Australia by Motorbike Yeah they look tuff! Wil check it out cheers mate 😊💯 Glad I can help in some way 🤙🏼

Hey man, love your videos, I've got an 08 ns paj and when I shift from P to R/D I get a very small thud similar to one at 3:50. Is this a diff bush related thing?

@budget4x4life

Жыл бұрын

Thanks matey 😊 mmm could be. Just check your bushes. Is it on hills only or on even ground? If it's on hill it could be because your hand brake is mot holding it in one place. On even ground I reckon bushes or could just be that gearbox connects to driveshaft when you go to D💯

@hgoods0193

Жыл бұрын

@@budget4x4life Regardless of where the car is I hear it. I've been told bushes could be the culprit but if they're all good it may just be the driveshaft connecting, good shout. Cheers :)

@budget4x4life

Жыл бұрын

@@hgoods0193 no worries mate. Grap a ply bar and check bushes😄💯

What engine does it have?

@budget4x4life

Жыл бұрын

4m41 3.2 Diesel 💯🔥

Full of the sickness number 10 yuleh. I got a number 10 ratchet spanner to do it Hella quick

@budget4x4life

10 ай бұрын

Awesome!

@budget4x4life

8 ай бұрын

@@chrro466 right 🤣

If I get in the paj after the wife drives it I always get the clunk out of park:(

@budget4x4life

Жыл бұрын

Yikes haha. Not a good feeling when that happens right 😬💯