Thank you bro ... God bless you

@jlcworkshop

Жыл бұрын

You're welcome brother

Thank you 👍

Magandang gabi brod. Baka matulongan m ako truble shot itong tinatrabaho makina sa man cla 18_280 mag overheat. Akin na ito top overhaul. Pinalitan ko na ito linner, piston ring cylender head gasket. Nozzul tip. Bagong calebret ang injection pump.umaandar na. Pagkatapos palyado. Mag overheat. Dati overheat ang problema nito.

@jlcworkshop

27 күн бұрын

Saan location mo sir?

@jlcworkshop

27 күн бұрын

Ano ang injection pump nyan sir?rotary ba or inline.sa ppagkakatanda ko kapag rotary injection pump.35degress btdc ang injection timing.kung inline nman ay 13 degrees

please make a 30 minutes explanation video on adjusting valves, tdc, ebs and the logic. please please . even if you dont film at the truck, oits ok if you flm in front of a drawing board and explain why TDC and all the rest. what means running mate etc . thank you . make a video so that alll normal DIY truck owners should understand . it will be the most amazing video i assure you .

Informative and helpful

@jlcworkshop

Жыл бұрын

Salamat manoy

Sending full support from san vicente cam norte...pashout po lods

@jlcworkshop

Жыл бұрын

Cge padi d lang kc nakakagawa pa ng bagong video.salamat

Respct to you comrade!...

@jlcworkshop

5 күн бұрын

Thank you Sir

wow galing talaga hehe

@jlcworkshop

Жыл бұрын

Hahahahha tsamba lang

Galing ser salamat sa pagshare done watching like subscribe done

I have issue in eletrical malfunction, ENGINE RPM lever is not working, what was issue may be

Thank sir

Where is your workshop

Hello brother i want to my vehicle where is your workshop

I have issue mantruck Model 2015, - 385

❤🎉 thanks 🙏

How much clearance you fixed

Hello. Why you must make first EVB 0 clearance to adjust exhaust valve?

@jlcworkshop

Жыл бұрын

Hi sir,to get an accurate adjustment and clearance.

Good pm bro anong max and min torque sa cylinder head d2066 /con rod at main bearing

@jlcworkshop

5 ай бұрын

Nakalimutan ko sir nandon kc sa record book ko.pero pakisearch din po sa google baka meron yan.sa pagkakatanda ko.yong main bearing ay 300nm plus 90 degrees.conrod bearing 100nm plus 90 degrees at cylinder head 300nm plus 90 plus 90.

Boss matanong ko lng boss ano ba iyung dapat gawin boss pag ang man tgm 18.240 nag indicate sa cluster nang "check fuel supply" sana mapansin boss salamat

❤

How are you

Shot out paps

Good morning sir I am facing a problem with D2676 MAN eingen. There is creating pressure in readiator i changed readiator and air Compressor pump but problem is still as it is . Please help

@jlcworkshop

Жыл бұрын

Hi sir.what kind of cylinder head that one sir?is that single inline cylinder head or indibidual?

@jlcworkshop

Жыл бұрын

Actually that was also happened here.creating pressure even radiator and air compressor are new.so we was dismantled the head and check the liner and clean.the after that,pressure is gone

@sukhwindermahal7073

Жыл бұрын

Singl head

@sukhwindermahal7073

Жыл бұрын

Make a vedio we will thankful to you

@sukhwindermahal7073

Жыл бұрын

Clean liner you means Piston liner or water lines

Hello sir,,Although the letter N does not appear, the engine is running... Please what is the reason

@jlcworkshop

Жыл бұрын

Hi sir,actually i cannot experience that kind of trouble yet,but i want to know if when you shift in reverse,letter R showing?

@jlcworkshop

Жыл бұрын

And hows if you shift in first gear or second gear third gear.number is showing or not?

@rabah8452

Жыл бұрын

yes sir it shows the number R....and everything is fine..

Good job sir . Saan Po kayo sa saudi Po .Anong company Po??

@jlcworkshop

Жыл бұрын

Dito ako sir sa al kharj

@charlitoautor8243

Жыл бұрын

...boss pwd malaman kung anong dapat gawin...nakalagay sa dash board ...malfunction on board computer...tas ayaw na nya mag matic magagamit mo as a manual nlng...salamat boss...

@jlcworkshop

Жыл бұрын

@@charlitoautor8243 sensya na po sir d kita nareplayan agad ok na po ba yong unit nyo?

Hi

Sir ilan poh valve clearance in / ex

@jlcworkshop

Жыл бұрын

Nasa video po sir.

@jlcworkshop

Жыл бұрын

Intake--0.5mm Exhaust--0.8mm Evb--0.6mm

Hu

Hi