This video is by far the best instruction on how to do this, thank you so much

awesome thanks, saved me the cost of taking it to cartoys just because I had no idea where this wire is supposed to go. I have it running from the door which sucks, this is going to make it way more pro

Thank you for this video! It helped me with the HID lighting for my accord.

Best explanation I’ve found! Kudos bro

Thank you Just fished a wire from the passenger compartment to the battery on a 2020Honda CRV hybrid. Mine was a little different but close enough for this to be very helpful. I would never have thought to go through the wheel well but it worked great.

Sweet. This video has opened my eyes and I am going to run 4 awg power wire through there myself. 💪

Thank you very much for this very well done and helpful video.

Very helpful video, it makes my life easier. Thank you.

You're a lifesaver...I think. On to my project tomorrow!!!

Great video, thank you, hello from Panama🇵🇦

Thanks, been looking all over for this info. Subbed.

Gracias, good work, and so simple. Great Video😉

Very nice, thanks for the effort to make this.

Great helpful video. Thank you.

Thanks so much I couldn't find a square inch to poke a hole through for the new OEM fog lights installation without fearing having water to run out off , the next solution was to lift the motor lol !

Damn worked like magic. Thanks

You the man!

THANKS I AM GLUD YOU HELPED ME YOU ARE GREAT TYTY

Thank you buddy

Thanks 🙏🏻 perfectly said

Thank you

Thanks!

Hey, that is a good video, will this apply to a 2011 Honda Fit Routing a Wire thru the firewall starting adjacent to the circuit breaker panel?

Will a 0G wire fit through there? im trying to get subs installed. Thanks!!

Is the hole big enough for 0ga welding cable?

Thank you for the easy-to-follow and informative video! Quick question: are those three grommets also located on the passenger side? I plan on installing a powered sub under the passenger seat and wonder if running the wire on that side would be easier. Thanks!!

What I did without prying the the wheel well cover and only popping off the cover inside the engine cover was that I used an soldering wire (Bend it to a hook) and then insert it from the fire wall into the engine bay and then pull my wires. Took around 5 minutes to find it (you might need a friend to wiggle/rotate to make it easier).

@Striker50_

3 жыл бұрын

Takes longer than just opening the wheel well

@nhantrinh0202

3 жыл бұрын

I used a dry cleaning metal hanger, straighten it and push through from the fire wall to the engine bay. It was long enough that I could do it by myself.

Thanks for posting!

do you think you can fit a 0 gauge wire thru that hole?

Are those holes available in all accords or just this gen?

Wish I could find something for the 2020 crv. Gonna just route my underglow kill switch though the driver side firewall grommet. Make a small hole

Was that a power wire or a remote turn on wire ?

How did you get the wire up there

Where can I bolt a ground cable in a 2014 Honda accord? Trying to connect a small fender light bar.

@DIYCarModz

Жыл бұрын

Pretty much any where on the chassis, support beam, metal.. drill, sand off paint and use self tapping screw.

Thank you for uploading this. I'm a noob, so would there be any downside of running a switch harness like this or should I wire it via the firewall?

@stinkletoes8285

10 ай бұрын

You need rubber gromet around that wire that you fed wire into foot area...that wire will chaff from vibrations etc and wear through.

How do you keep your engine bay so clean?

@jeffa4133

3 жыл бұрын

I was just about to ask the same thing.

What wire did you tap into for the fog light switch for the inside

@DIYCarModz

Жыл бұрын

If you are adding foglight to your vehicle, I would use a relay harness and tap constant on fuse with the correct amp fuse.

What Guage of wire did you use that fit? Hard to tell from video, but looks as if a subwoofer 10awg or 12awg may be too large to fit which is what many would like to do

@jacrispy8802

2 жыл бұрын

I fit 4 10 awg wires through the hole, you should be good.

@michaelprouty9363

2 жыл бұрын

i just did sub power cable with room to spare

Very cool, I never would have thought it was that easy. What is the cable for?

Wow thats incredibly easy. Im gonna install some stupid mods.

GLAD TOO>>>LOL

Second view lmao