The car looking good man

@unclejacksyoutube6496

5 жыл бұрын

Thanks has a lot of work still lol

This car is wild 👀👀👀

@unclejacksyoutube6496

4 жыл бұрын

ItS jUsT a 5.o

Where dose the tach wire go ? Literally doing this rn

@unclejacksyoutube6496

5 ай бұрын

You don’t have to use it. A normal tach gauge will have one wire for looking for a signal. If it’s a factory gauge idk lol

@princeg2184

5 ай бұрын

@@unclejacksyoutube6496 man that grey tach wire been kicking our ass lol

The guy I bought my poor car from an idiot that was like "it revs to 7k" *revs it out to 7 grand* I thought it was about to blow right there. swooped it up for $2500 and it's not a bad 91 coupe if I say so myself.

@yungblaze223s

3 жыл бұрын

Brave. How is it holding up

@Mr.Potato420

3 жыл бұрын

@@yungblaze223s Not even a check engine light after some o2 sensors. runs great!

@unclejacksyoutube6496

3 жыл бұрын

its called husltin

I need my 86 to sound like that

@unclejacksyoutube6496

2 жыл бұрын

The exhaust is pretty aggressive lol

When you hook up the two step do you take the wire for the two step and a wire with twelve volts and just hook them up to a button? And when you do two step do you just hold it at full throttle?

@unclejacksyoutube6496

2 жыл бұрын

Yep a hot wire to the 2 step wire. If you give 12v to the 2 step wire the rpms will not go over what you have them set to on the dials. And with a carb car I’d play with it first. Don’t full throttle it first time. If you full throttle it I’m sure it’s gonna make some bangs and pops.

To oparate 2 step in automatic cars, do we use button also? To open and close 2 step..

@unclejacksyoutube6496

3 жыл бұрын

Hmmmmmm well a button would be simple but there is all kinds of options. Maybe the brake pedal switch? I know that is common with aod foxes but be careful bc the higher the rpm the more of a chance of breaking something.

I bought the same msd for my 95 mustang and was wondering if you could help. For the wires, which wires do you have connected to that switch? Lol I don't know where to get the 12v from.

@unclejacksyoutube6496

3 жыл бұрын

Yeah I had the same issue. So i would recommend a fuse tapper and put a switch in line. And the wire on the box to activate it is the blue wire I think.

@unclejacksyoutube6496

3 жыл бұрын

There is all kinds of ways to do it though.

@TheRoach156

3 жыл бұрын

@@unclejacksyoutube6496 Oh okay, gotcha thank you!

I have an 87 fox GT could you put a link to what I need

@unclejacksyoutube6496

3 жыл бұрын

Holley efi website. Msd 6al2 ignition box. Ford tfi harness. I don’t have time to go back and find the links rn but it’s simple I promise.

I have a 68 mustang with a fox 5.0 in it, with a carb and a petronix ignition module. Any idea what it would take to put the 6al on it???

@unclejacksyoutube6496

3 жыл бұрын

What do you mean by ignition module? Like a box or the petronix conversion in the distributor? I’m not real familiar with petronix products for a sbf

@68_deathtrap90

3 жыл бұрын

@@unclejacksyoutube6496 it’s the ignitor 3 distributor module

@unclejacksyoutube6496

3 жыл бұрын

Ok so I looked it up and the petronix says a msd box isn’t recommended. Buuut plenty of people in the forums say they have been doing it for years and never had a problem. So personaly I’d say it’s safe. Keep in mind that the msd box is just amping the coil up. If you buy the box and follow the directions it should work. I’d recommend the 6al2 box bc it comes with the limiter and 2 step features built in. If you do it let me know how it goes👍🏼

@68_deathtrap90

3 жыл бұрын

@@unclejacksyoutube6496 so I did a little bit of digging myself and here’s what I found So the ignition module I have is a ignitor 3, which is different that the 1 and 2 because I has a “box” built into it (ie it already has multi spark, rev limiter, ect) so if I put a box on top of that I’ll blow up the coil. So I might just see if I can graft in an mad 2 step module instead. Thanks for the help man I’ll keep you posted Btw my Instagram is 5.0stang_68

@unclejacksyoutube6496

3 жыл бұрын

Yeah that makes sense. I’m very curious if it will work

What RPM are you shooting the flames at ?

Where did you get the clear indash cover??

@unclejacksyoutube6496

3 жыл бұрын

My soon to be website😉

I’ve got an 86, so all I have to do is buy this and install it? Nothing else?

@unclejacksyoutube6496

Жыл бұрын

Yep

I have a carbureted car, so do I hold the gas all the way down still?

@unclejacksyoutube6496

2 жыл бұрын

i would hold it a little. and then a little more. and just maybe a tad more. if everything sounds and feels ok id go just a itty bit more. point is test and tune. but be cautious lol

Can this be done with the 6al box?

@unclejacksyoutube6496

3 жыл бұрын

Yes of you buy the separate 2step module. I’ve priced it and it will cost you the same.

@haydenhale7416

3 жыл бұрын

@@unclejacksyoutube6496 ok thanks man, I already have the box do you know I set what rpm

@unclejacksyoutube6496

3 жыл бұрын

I have mine at 3300

So the msd wiring pretty much goes in-between the stock connector to the coil?

@unclejacksyoutube6496

4 жыл бұрын

Yep. They even have a harness made so it’s literally plug and play 2 step

How would I do this with a distributor-less or non dibby old GM V6 that's runs on coils?

@unclejacksyoutube6496

4 жыл бұрын

Pretty sure you can’t use this or any box like the one shown here. I believe your gonna want something from n2mb. I’m not familiar with distributorless ignitions. I mean I know how they work but as far as modifying it I’m blank. But I know people use n2mb for newer stuff. Also may be able to tune in 2step. I know with a new edge v6 mustang (one coil for all cylinders) that’s what’s recommended. I hope you have good luck with it bc I know how hard it is to find stuff on this lol let me know if you do anything and it works👍🏻👍🏻👍🏻

@unclejacksyoutube6496

4 жыл бұрын

Ok so I just searched it and I’m pretty sure you want the n2mb wot box. If it’s a coil per cylinder that’s what its for.

@Coronet_shop

4 жыл бұрын

@@unclejacksyoutube6496 definitely check it out

How do you make it rev slower like pop pop pop not ppppppp

@unclejacksyoutube6496

4 жыл бұрын

Welllll only thing I know to do is convert to coil on plug. But I promise this setup is insane and will do the job lol

@tomashernandez279

4 жыл бұрын

Legacy thx

@unclejacksyoutube6496

4 жыл бұрын

Man no problem but i asked the same question years ago. And Holley (msd) has a kit that takes control of your timing. It’s like $1200. And if you want the part number I’ll post it. but If that’s what you want I’m sure it will do it. But I spent $300 and shot big ass flames and got some women lol if that’s the end goal $300 will do it👌🏻👍🏻

@tomashernandez279

4 жыл бұрын

Legacy thanks bro😂

@unclejacksyoutube6496

4 жыл бұрын

Anytime lol

Has the 2 step hurt anything yet?

@unclejacksyoutube6496

3 жыл бұрын

Nah not really I cut the wire to activate it bc I was attracting to much attention from the popo. I put the two step on with a sticking lifter and it hasn’t got any worse or any better.

How do you launch tho?

@unclejacksyoutube6496

2 жыл бұрын

Ok so that’s where it gets complicated. Maybe the 12v can come from your neutral safety switch or a button on top of the shift knob. Or on your steering wheel. You give the blue wire 12v any way that works for you and gets you there the fastest if that’s your goal.

So loud for a car that I thought it was Anti-Lag O_O

@unclejacksyoutube6496

3 жыл бұрын

It does turn up pretty hard for a sbf lol

What rpm is this?

@unclejacksyoutube6496

4 жыл бұрын

3300. Sorry I didn’t put in vid lol

@tonyginn799

4 жыл бұрын

Naw you’re good brother I got mine set 3500 and I have a 600 lift cam big heads and it’s not shooting any flames so I was just curious

@tonyginn799

4 жыл бұрын

Also do you have a muffler or cats?

@unclejacksyoutube6496

4 жыл бұрын

No cats or mufflers. Bbk 1 3/4 long tubes, bbk off-road h-pipe, and custom made straight pipe cat back. Amazing sound all the time at any rpm.

@cfmechanic

3 жыл бұрын

@@tonyginn799 to shoot flames u need straight thru mufflers carven slp magnaflow etc, and running a 2 step thru cats is very hard on them...there is a vid of a bmw running 2 step launching molten cat material out the pipes

The popping and flames are from late combustion when the exhaust valve is open. Rev limiters cut/retard the ignition to control the RPM but they do not cut the fuel. Combustion happens just before the piston reaches the top of the cylinder when your timing is advanced using the explosion to push the piston down the cylinder. When the box retards the timing the combustion happens after the piston is already on its way down and instead pushing the explosion out an open exhaust valve. Hence the popping and flames out the exhaust pipe. Anti-lag adds more fuel to increase combustion in the exhaust to keep a Turbo Charger spooled so there will always be boost on tap. But that's another story .

@unclejacksyoutube6496

3 жыл бұрын

Timing is a lot of it but how hot the tubes are and what size tubes in the exhaust is another big factor on a flame making a actual flame.

😂😂😂 I love that sound 😂😂😂

@unclejacksyoutube6496

4 жыл бұрын

Me too lol

My man your car is basically gone stock your not bending no axles LOL that’s hilarious

@unclejacksyoutube6496

3 жыл бұрын

Exactly lol that’s the whole point.

Janky asf

@unclejacksyoutube6496

2 жыл бұрын

That’s not even the word I would use to describe it.