Great videos, getting myself a chest freezer this week and I will be running the same setup. Question regarding the drainage. If the waterlines are running over the sides of the freezer does this drainage system still work(i.e Split return/Input hose)? From my understanding this drainage setup works because of the hole at the bottom. I was thinking of splitting the Output hose coming out of the pump before it passes the ozone generator for drainage. What do you think?

@HandsOnMeditation

Жыл бұрын

If you mean to drain all the water out of the freezer, that won't work. It would only drain the water out of the pump, but there won't be any suction to pull the water up over the sides and out of the freezer. When I was running the hoses over the sides of my freezer, I used a siphon method to drain the water out. You put a hose in the freezer water, then you put the opposite side of the hose at a lower level (I put it in a sump pit). To get the water started, you have to create a little suction. I would hook up a wet vac and begin sucking water out. Once the water gets moving, you can stop sucking and the water will keep moving on it's own (as long as it's flowing to a lower level).

@musabihalmansoori3700

Жыл бұрын

@@HandsOnMeditation Thanks again for sharing. What are your thoughts on splitting (T joint) the output hose coming out of the pump before it passes the ozone generator for drainage? Basically using the filter pump as drain system.

@HandsOnMeditation

Жыл бұрын

I think you’ll still have the same problem. The pump will completely empty out right away and there will be no water flowing through it to keep the suction.

@trophysucka

8 ай бұрын

@HandsOnMeditation did you use a wet vac to get the filtration working? I burnt the motor on one of the Intex C1000 pumps already because I turned it on without any water in it. If suction is required to even begin using the pump I’m wondering how to do that

I just built my cold plunge to your exact specifications. Ran into a few snags here and there, but got it done. Thank you for the detailed video and the pdf's. Huge help.

@HandsOnMeditation

Күн бұрын

Glad it worked out for you. Have you watched any of the other videos on this channel? And would you like to share any pics of your final project? You could do so on our community page

Best setup thus far. Thanks

@HandsOnMeditation

4 ай бұрын

Thanks. Have you watched my other cold plunge videos?

@jimng6502

4 ай бұрын

@HandsOnMeditation Yes. Thanks

Perfect video, thank you.

@HandsOnMeditation

8 ай бұрын

Thank you. Please subscribe and share with friends. Have you tried any of the other exercises on this channel?

Great content with so much useful details, thank you! I’m considering to get a laser chiller CW5200, looks like the power is okay go cool the water just the pump comes with it only goes 13L/min, with about 200L in my bath tub I feel is enough to cycle the water in every 15min. Any suggestions on this one?

@HandsOnMeditation

10 ай бұрын

If you use a chiller, you could consider something like a large cattle trough instead of a freezer. You probably won't need a very large pump because it's not that much water. I've never worked with a chiller but I have considered it and may do so in a future project.

What fitting did you use for the pump to get into the deep freeze? I'm having trouble finding one that has long enough threads to go through the floor of the freezer.

@HandsOnMeditation

9 ай бұрын

Extra Long Thru-Hull Connector amzn.to/3eZ0bMy *Note: If your freezer floor is thicker than my example, you may need longer Thru-Hulls. There are a variety available online. This one is longer but will require a barb adapter to connect the hose. www.greatlakesskipper.com/mako-boat-thru-hull-fitting-3-4-inch-stainless-steel

i finally finished following your full "recipe" for making the cold plunge. I haven't been able to try it yet because it wasn't getting cold. Now i realize it must be due to the thermostat sensor interfering. I applied JB water weld to the storage clips areas i removed from the inside walls, and while i was at it i put weld over the sensor at the interior. Do you know of methods to disconnect the chest freezer's temperature control thermostat sensor, have any tips or know anyone in my similar position and what they did?

@HandsOnMeditation

9 ай бұрын

Sorry but I have not heard of anyone with this issue. I do see videos online about people replacing thermostat sensors. That may help. Is your freezer getting cold at all? You don't really need it to sense the temp, as long as it turns on. It can take a long time for the water to reach the low temperature depending on how warm the water is when you begin. It takes my freezer about an hour to lower the water temperature by one degree.

Hi, I’ve only seen this ozone generator with a 4 pin type of plug for circuit board. How did you convert it to electric cord?

@HandsOnMeditation

Жыл бұрын

You have to add a standard plug like this. Black (hot wire) to the smaller flat blade, White (neutral wire) to the wider flat blade, Green (ground wire) to the round pin. photos.google.com/share/AF1QipOjPu7K_MuhKyD4i0IkazwmuqRo3S9D-1T52-AmZd0b-AFmKGiWWzWteGfpl_nY3g?key=Tk4tWXR2Sm0zaEhFSlJBbkJFLXVXMUVZSTgwVDR3

@ 3:06 can you tell me the style U-pvc compact ball valve you are using? I'd like to purchase online but don't want to buy something incorrect

@HandsOnMeditation

10 ай бұрын

Anything like this will work well. amzn.to/3JRZTmZ You just have to size it to fit your pvc pipes. My pvc pipes are 1/2"

What Size PVC is that connected to the 3/4 inch ID Tubing? Sorry if it's a dumb question, but I see the tubing going over the PVC so I was not sure if it was the same size or not!

@HandsOnMeditation

10 ай бұрын

Have you looked at the first DIY Cold Plunge video on this channel? I have links and product info listed in the video description.

Do you get any condensation on the water lines running to and from the pump? I heard a comment in another video that the temperature difference between the water and outside air can cause lots of condensation on the hoses.

@HandsOnMeditation

8 ай бұрын

My cold plunge is indoors so the humidity isn't so high but if you keep it in a humid environment that makes sense. The water temp will also be affected by the air temp when running through the hoses so I don't run my pump continuously. If you are having issues, you may want to insulate your hoses.

Hi. Thanks for sharing. If I use the cold plunge 2 o 3 times per week, 5 minutes each time, do I have to run the ozone everyday?

@HandsOnMeditation

7 ай бұрын

It really just depends on how clean your water is. If you are building up a lot of body oils, soap, sweat, etc. in the water, you'll need to run ozone more often. If your water is staying clean, then it's not necessary. I would typically run the ozone after each use for a little while (around 5 minutes) and a couple other short bursts during the day.

I’m having trouble getting the pump to work. To be fair I’m running the hose over the edge of the bathtub and trying to hold the hoses under and mess with the pump without making a mess. Hoping that it will work once I get it all set up in the plunge and the hoses are zip tied in place. Planning on running the hoses through the lid. I hear you say If you’re running them over the side you’ll have to life the pump. Can you explain the process a little better?

@HandsOnMeditation

Жыл бұрын

You can get air pockets in the system while filling up the cold plunge and that can create problems for the pump. They will tend to float up to the highest point. If you are running your hoses over the sides of the cold plunge, that's the highest point. There is no easy way to bleed the air out (let it escape) at that point, so you can lift the pump up (with it turned off) a little above the hoses. Let the air pockets float up to your pump. Then unscrew the top of the pump (at the bleed valve) and slowly lower the pump. Water will push the air out. When you see water flowing out of the bleed valve, you can screw it shut and that should take care of your air pockets.

Hello, I hope you're well. I've often heard that you shouldn't get into the water while the freezer is still running, which I can understand. But I've also sometimes read that you shouldn't even touch the carcass as long as it's powered? What do you advise? Please, thank you in advance.

@HandsOnMeditation

8 ай бұрын

My freezer power is controlled by a smart plug. When I enter the room and turn on the lights, all power to the freezer and accessories shuts off so it's never on when I'm close by. I suggest you always error on the side of caution and use your best judgement.

I was wondering what pool pump you are using? Also, are you still liking your setup of having the lines coming from the bottom of the freezer? Thanks for the videos

@HandsOnMeditation

Жыл бұрын

Works much better with lines coming through bottom of freezer. Water circulates nicely and the pump works properly. If you watch my first Ultimate Cold Plunge video on this channel, I have links to the pump and accessories in the video description.

Can you leave JUST the pump going while using the cold plunge, since it isn't a submersed pump and is outside of the chest freezer and grounded? Keeping the water moving while using it would help prevent thermal layer.

@HandsOnMeditation

7 ай бұрын

Yes, you can leave the pump going. I've made some changes to my setup, if you watch my newer videos. Ideally, you would always keep the pump on to keep the water moving and filtered but you don't want power to the freezer or any other electric devices. I now use a UV Light Clarifier instead of the Ozone Generator and I don't want power running to that while I'm using the Cold Plunge.

After 4months with the OZ has your filter shown any issues with the Pump. Reason why I ask is because you have the hose coming out of the filter at about 1 1/4, which is a lot of water then condensing the amount of water going through the Venturi injector. I would assume that the pump would have to work harder because of that.

@HandsOnMeditation

11 ай бұрын

The pump is definitely working harder than if it was connected to an above ground pool, but mine has been running for a couple years and still going strong. I'm sure at some point it will break down but it's a pretty cheaply built plastic pump so I kind of expect it. I'm trying a UV clarifier and really like it. I may end up disconnecting the Ozone Generator and Venturi injector. That also effects the pump. I'll have a video up soon to talk about this.

Great video, thanks! How often do you need to drain the whole freezer?

@HandsOnMeditation

Жыл бұрын

At times, I've had three people actively using the cold plunge and I was changing the water about weekly. Other times when it's only being used by one person or only being used after showering, I can go several weeks without changing the water. My Cleaning Routine: 1. Drain it. 2. Give it a quick wipe, if needed. 3. Change the pump filter, if needed. 4. I like to pour a little peroxide in the pump. 5. Fill it back up with clean water. Then maybe a couple time a year, run hot water with a little bleach through the system for total sanitization.

@halifaxnaturopathicdoctor6227

Жыл бұрын

@@HandsOnMeditation thank you!

You deserve way more likes. Question do you seal then paint or paint then seal? I have an aluminium lined freezer so think I should line it straight away

@HandsOnMeditation

Жыл бұрын

I think it's best to seal first and then paint with Pond Shield, however you may not need to paint because aluminum doesn't rust. My freezer has painted steel sides. In some areas, there were scratches that began to rust so I decided to paint it all.

@traingamegain2434

Жыл бұрын

@@HandsOnMeditation thanks!!! Your setup is an inspiration . I love the details in the space - thanks for sharing everything

@HandsOnMeditation

Жыл бұрын

Thanks. Please spread the word and let me know how your setup goes.

@joshua10172

Жыл бұрын

Hey, paint with an epoxy. And use ‘pool blue’ or ‘sky blue’ or ‘robin egg blue’ as a colour. You won’t regret it. That colour is relaxing. And you will need all of the help relaxing you can get when starting out.

@HandsOnMeditation

Жыл бұрын

Do you have some pictures you would like to share? Sounds interesting.

With the smart plugs you use to turn off the freezer, is it still necessary to unplug the freezer before using to eliminate the risk of electric shock?

@HandsOnMeditation

Жыл бұрын

You should just ensure that no power is going to the freezer when you are using it, to be safe.

For the ozone generator did you cut the 4 pin plug and convert it to a regular one?

@HandsOnMeditation

9 ай бұрын

Yes. Green wire to ground pin. White to left blade, black to right blade. photos.google.com/share/AF1QipOjPu7K_MuhKyD4i0IkazwmuqRo3S9D-1T52-AmZd0b-AFmKGiWWzWteGfpl_nY3g?key=Tk4tWXR2Sm0zaEhFSlJBbkJFLXVXMUVZSTgwVDR3

Does the connector for the ozone constrict the flow of water by the pump? It looks like it goes from a large pump tube into a small straw size pipe for the ozone.

@HandsOnMeditation

11 ай бұрын

The small tube carries ozone to the venturi injector. Water doesn't travel through the small tube, it continues through the larger openings on either side of the venturi injector.

@user-oj4ub9gu2j

11 ай бұрын

I’m having issues with mine, I don’t see any bubbles from the injector. I used a different and larger injector, could that be the issue? Light is on and everything, but no bubbles inside the ice bath. Thank you for your time.

@HandsOnMeditation

11 ай бұрын

Are you using a Venturi injector and is it facing the right direction? Are you also using a check valve and sure it’s facing the right direction?

@user-oj4ub9gu2j

11 ай бұрын

I’m using an ozone injector from waterways, it and the check valve are facing the proper directions. Should the tube from the generator be straight? Or does it matter if there is a small loop?

@user-oj4ub9gu2j

11 ай бұрын

Figured it out, it needs the Venturi connector specifically. The one I got from waterways was the issue, 100% now!

Hi, nice video, what kind of paint you used for your freezer?

@HandsOnMeditation

11 ай бұрын

I painted the inside with Pond Shield paint. There's another video on this channel that talks more about it.

Does This Ozone generator run the entire time its plugged in, i would like to run my pool pump and ozone generator on a smart plug to run for 1-2 hours daily automatically without having to manually turn on and off the ozone generator and pump. so i was looking into what ozone generator would automatically run as soon as it get power from the smart plug.

@Travisl8r

10 ай бұрын

@handsonmeditation

@HandsOnMeditation

10 ай бұрын

I plug my ozone generator into a smart plug and only run it for 10 minutes after each use, and then a few more times for 5 minutes. There is no switch. As soon as it gets power it runs, but I don't think there's any reason to run it for long periods of time. Also, you have to run the pump at the same time and the water will start to warm up when the pump is running (because the hoses are on the outside of the cold plunge). So, I recommend only using the ozone generator for short periods of time. You also don't want to build up unsafe levels of ozone. I'm actually experimenting with a UV Light Clarifier and it's working really well. I may use that instead of the ozone.

Hey, nice setup! About how often do you drain your water?

@HandsOnMeditation

6 ай бұрын

It depends on how many people are using it, but if my wife and I use it every day, I can usually go 2-3 weeks before changing the water. I just updated to a UV Clarifier instead of the Ozone Generator and a pump with whole house filter. That seems to work better. I'll have a video to explain soon.

Do you think the filter actually does very much? I was debating on just using a pump.

@HandsOnMeditation

Жыл бұрын

The filter does catch hair and some debris, but the filter also gets slimy and might be a breeding ground for gunk. If you try without the filter, please let me know how it goes.

@robertreeves6631

Жыл бұрын

I am having so much trouble with leaking. Were you able to seal everything with pipe clamps no problem? Like I see the PVC from underneath....what did you use to connect the PVC to the through port?

@HandsOnMeditation

Жыл бұрын

I have section of vinyl tubing between the thru hull and pvc. My tubing is a very tight fit over the parts. I have to heat the tips in hot water to stretch over. The hose clamps are barely needed. You must have tubing that is too wide. Try a slightly smaller diameter tubing. It should be really tight.

I was wanting to put a plunge in a storage room in my basement. Was worried about using ozone since it's not very well ventilated in that room. How do you manage any toxins being in your basement as well?

@HandsOnMeditation

9 ай бұрын

I only run the ozone generator for short periods of time, however I suggest you try a UV Light Clarifier instead. It works just as well and there is no risk of building up unsafe levels of ozone. I'll have a video to show soon.

@justinmcclintock638

9 ай бұрын

Thanks!@@HandsOnMeditation I did find a video on using UV instead, and was going to try that route first. I may end up moving it to the garage after a while if I want to try using ozone

How the drain T and ball valve are set up don’t you lose half of the water back into the system you’re trying to drain?

@HandsOnMeditation

Жыл бұрын

The separate black drain hose is lower than the pump and freezer, so all the water drains out to my sump pump pit as soon as I open the valve.

@corymarx8545

Жыл бұрын

Understood. Was thinking about running a similar set up. And letting the filter pump empty my tank by a tee in the return line. Ball valve to divert out the drain and ball valve to block the return line to the tank.

@HandsOnMeditation

Жыл бұрын

I'm a little confused. I'd need to see a diagram of your idea. You should be able to do this like me with a single valve.

How did you find an ultra pure ozone generator with a regular wall plug. I can’t find it anywhere

@HandsOnMeditation

Жыл бұрын

You have to add a standard plug. It doesn’t come that way. If you watch my first video I give the specifics. Although I’m having just as much success, maybe even better results with a UV clarifier. You might consider that instead.

@OHNOHELLNOno

Жыл бұрын

@@HandsOnMeditation if you have one to recommend please post it. Or link me to the video you did of it. Thank you

@HandsOnMeditation

Жыл бұрын

This shows the one I’m using and there’s a link in the description. kzread.info/dash/bejne/kY6kxKyBpLeTn7g.html

What size freezer are you using?

@HandsOnMeditation

Жыл бұрын

I believe it's a 14.8. If you check my first Cold Plunge video on this channel, all the info is listed in the video description.

What size is your freezer?

@HandsOnMeditation

Жыл бұрын

The freezer is 14.8 cu. ft. That's a common size for chest freezers. I'm 6' and it fits me pretty well. I wouldn't want to go any smaller. If you watch the other cold plunge videos on this channel, I have more specific information.

Why don’t you use a thermometer to control the power to the tub?

@HandsOnMeditation

9 ай бұрын

What thermometer do you recommend? I would have to control a power source.

U do online lessons for intermediate?

@HandsOnMeditation

8 ай бұрын

Lessons about what? Have you checked out the other videos on this channel?

@DiegoRodriguez-je2ok

8 ай бұрын

@@HandsOnMeditation hahaha idk how my comment ended up on this channel .

Good video. Is this in your basement or garage?

@HandsOnMeditation

Жыл бұрын

It's in the basement. No room in our garage and the temperatures get too cold where I live. If you watch the other cold plunge videos on this channel, you can see the full room. There is also a sauna.

@normalguy7898

Жыл бұрын

@@HandsOnMeditation thanks I've watched a few. Looks like a good setup!

@HandsOnMeditation

Жыл бұрын

Are you also building one? At some point, I'll probably update the design a little and video the complete build as I make a new one.