Great video. I enjoy make my own tools also. I came across drill rod, size very consistent. Thank you
@JamesCouch777 Жыл бұрын
I've made a bunch of my own tools. I have almost everything I need at this point but if I need something different I just stop and make it. Good job on the tools 👍
@hayesrutherford94154 ай бұрын
New sub. I like to make my own tools so had to check this out.
@hswing116 ай бұрын
GREAT VERY INFORMATIVE
@JohnWilliams-oq5nm
5 ай бұрын
Glad it was helpful!
@nevilleklaricich4548 Жыл бұрын
Hi John - great tool making demonstration. Thank you for the bit of crucial information about the tool tip needing to be in the same axis as the shaft. A friend with a forge made one for me and I have been wondering why I haven’t been able to hold it whilst turning. I will definitely keep it in mind on the next one I make. Greetings from Australia.
@JohnWilliams-oq5nm
Жыл бұрын
Neville - thanks for watching and for your kind comment. I’m glad you found some helpful information. Also, thanks for the Greetings from down under! I send Greetings and Thanks from Tampa, Florida!
@josephwise4854 жыл бұрын
Very inventive. Thanks for sharing your process, and AZ Carbide Safe turning.
@JohnWilliams-oq5nm
4 жыл бұрын
Thank you Joseph. This is a Zoom presentation done for my turning club. Hope it was helpful.
@cjphillips6648 Жыл бұрын
Those are great! The large ones that are sold on Amazon, are expensive. You have a nice simple set of products there, I would buy them!
@JohnWilliams-oq5nm
Жыл бұрын
Thanks! They work for me.
@JohnWilliams-oq5nm
5 ай бұрын
Thank you! Not sure I could afford the liability insurance if I were selling them!
@danstevenson91243 жыл бұрын
Hi John. Great tool demo, now I need a demo on building that little furnace as well. Love those lil' hoggers as well.
@JohnWilliams-oq5nm
3 жыл бұрын
Hey Dan, my “stones” are behind me and should have time to come visit next week. Glad to help where I can.
@danstevenson9124
3 жыл бұрын
@@JohnWilliams-oq5nm Glad to hear it. Anytime. And I have your next giant sink log ready for you...bring your crane system lol.
@johnmitchell16142 жыл бұрын
Hello John. I happened upon your channel by chance, and I'm glad I did. It is most interesting and informative. Best regards.
@JohnWilliams-oq5nm
2 жыл бұрын
Thank you!
@mikefields92163 жыл бұрын
Happy Thanksgiving to you and Family!!
@JohnWilliams-oq5nm
3 жыл бұрын
Thanks
@desjanwirges8397 Жыл бұрын
Hi John, Enjoyed your alternate view on expensive turning tools. I was intrigued by the drill reground as a cutter but can't find the guy's site you mentioned. Could you please offer some more detail Best wishes Des
@JohnWilliams-oq5nm
Жыл бұрын
Here you go, hope this helps. kzread.info/dash/bejne/hq2Cj7STf7OoZLA.html
@wdnick3 жыл бұрын
Hi John. What angle are you shooting for on the end of your bars?
@JohnWilliams-oq5nm
3 жыл бұрын
I assume you mean the angle at the end of the shaft where the cutter is mounted. 30 degrees is what I have been using. It seems to work well with the AZ Carbide cutter and will take off a lot of material.
@jeneiferthomas1036 Жыл бұрын
Mr Williams do you sell these? If so how much for the little hogger
@JohnWilliams-oq5nm
Жыл бұрын
Jennifer, sorry but I do not sell them. Thanks for watching and for your question.
Пікірлер: 27
Great video. I enjoy make my own tools also. I came across drill rod, size very consistent. Thank you
I've made a bunch of my own tools. I have almost everything I need at this point but if I need something different I just stop and make it. Good job on the tools 👍
New sub. I like to make my own tools so had to check this out.
GREAT VERY INFORMATIVE
@JohnWilliams-oq5nm
5 ай бұрын
Glad it was helpful!
Hi John - great tool making demonstration. Thank you for the bit of crucial information about the tool tip needing to be in the same axis as the shaft. A friend with a forge made one for me and I have been wondering why I haven’t been able to hold it whilst turning. I will definitely keep it in mind on the next one I make. Greetings from Australia.
@JohnWilliams-oq5nm
Жыл бұрын
Neville - thanks for watching and for your kind comment. I’m glad you found some helpful information. Also, thanks for the Greetings from down under! I send Greetings and Thanks from Tampa, Florida!
Very inventive. Thanks for sharing your process, and AZ Carbide Safe turning.
@JohnWilliams-oq5nm
4 жыл бұрын
Thank you Joseph. This is a Zoom presentation done for my turning club. Hope it was helpful.
Those are great! The large ones that are sold on Amazon, are expensive. You have a nice simple set of products there, I would buy them!
@JohnWilliams-oq5nm
Жыл бұрын
Thanks! They work for me.
@JohnWilliams-oq5nm
5 ай бұрын
Thank you! Not sure I could afford the liability insurance if I were selling them!
Hi John. Great tool demo, now I need a demo on building that little furnace as well. Love those lil' hoggers as well.
@JohnWilliams-oq5nm
3 жыл бұрын
Hey Dan, my “stones” are behind me and should have time to come visit next week. Glad to help where I can.
@danstevenson9124
3 жыл бұрын
@@JohnWilliams-oq5nm Glad to hear it. Anytime. And I have your next giant sink log ready for you...bring your crane system lol.
Hello John. I happened upon your channel by chance, and I'm glad I did. It is most interesting and informative. Best regards.
@JohnWilliams-oq5nm
2 жыл бұрын
Thank you!
Happy Thanksgiving to you and Family!!
@JohnWilliams-oq5nm
3 жыл бұрын
Thanks
Hi John, Enjoyed your alternate view on expensive turning tools. I was intrigued by the drill reground as a cutter but can't find the guy's site you mentioned. Could you please offer some more detail Best wishes Des
@JohnWilliams-oq5nm
Жыл бұрын
Here you go, hope this helps. kzread.info/dash/bejne/hq2Cj7STf7OoZLA.html
Hi John. What angle are you shooting for on the end of your bars?
@JohnWilliams-oq5nm
3 жыл бұрын
I assume you mean the angle at the end of the shaft where the cutter is mounted. 30 degrees is what I have been using. It seems to work well with the AZ Carbide cutter and will take off a lot of material.
Mr Williams do you sell these? If so how much for the little hogger
@JohnWilliams-oq5nm
Жыл бұрын
Jennifer, sorry but I do not sell them. Thanks for watching and for your question.
John do u make bars for others,
@JohnWilliams-oq5nm
5 ай бұрын
I have. What did you have in mind?