my savior. had to check why my moms oil pressure was so low and this was why. Thanks for the great video

@blindguysgarage

Жыл бұрын

Your welcome one of the most common issues is the oil pump pick up O-ring also a good high volume pump in an LS engine never hurts either

Awesome video I was dreading doing mine due to the front differential but seeing you do it this way motivated me to do it this weekend

@blindguysgarage

Жыл бұрын

All you have to do is loosen the oil pan bolts all around and be very carefull taking the one oil pickup bolt out the rest is gravy

Great video 👍 And the way you did your oil pump install was nice. I have seen some people shim the pump gear first before bolting the whole pump together. Is that even necessary ?

@blindguysgarage

Жыл бұрын

Thank you as for shimming the pump I have changed mine of these and never needed to. I hate dropping the oil pan and as I said I like to disassemble the pump clean it and pack it with Vaseline any way just the way I was taught to do these things. It is supposed to help pickup oil faster and lubricate the pump untill it gets oil.

Pretty solid video. 2013 avalanche 100k mi A few questions. I have full dod delete., cover bare lifters timing chain 20k miles ago. The melling high volume pump oil pressure has never been great. Less than 40 cold 19 or 20 hot then just started dropping low less than 10 and lifter tick. Where would you start on this? Do you think I had a bad pump out the box or something else? I already spent 4k and don’t really have the money to throw at it. Should I just bite it and try a new pump? Thanks man for any help.

@blindguysgarage

2 ай бұрын

Probably a bad pump, but I have to ask. Did they do a DOD tower plug kit because it also could be the O-rings on your DOD plate If it were mine, I would pull front cover and replace oil pump and cam thrust plate And hope that makes the issue go away, unfortunately without seeing it in person kind of hard to tell what exactly to do, but that’s definitely where I would start

@blindguysgarage

2 ай бұрын

Also, the reason you’re not seeing extremely good oil pressure is because these have a check valve made into the oil filter housing in the oil pan that is designed to let pressure off so it won’t over pressurize the DOD system

I think i missed it, did you a standard or high volume pump?

@blindguysgarage

Жыл бұрын

I use a High volume oil pump on these and if I rember right the factery also uses a high volume pump on all AFM-DOD engines

Why’d you pack the oil pump with Vaseline

@blindguysgarage

Ай бұрын

I do this to make it easer to pickup oil not really required but was tought to do this so just always have

How long did it take you to do the oil pump? I’m having the same problem. I have a 2009 GMC Yukon Denali 6.2 L and I changed the oil pressure sensor three times and it’s still on so we found out that I need to get an oil pump now. What do you think I should do because the truck now won’t start.

@blindguysgarage

3 ай бұрын

Not starting is a terrible thing. Probably has already done the damage. If it is the oil pump it’s only a couple hour job.

@tonalinamoore659

3 ай бұрын

I think you are definitely right it’s making already loud sound and also the motor is shaking as I can tell when I started it up I had to jump it today to get it started. After I jumped it and let it run for a while and then I turned it off. It wouldn’t start back up it just got this noise ,Just need a little advice on what to do at this point and thank you again for responding back.

@blindguysgarage

3 ай бұрын

@@tonalinamoore659 can’t tell you for sure without hearing it myself but if you are having to jumpstart it, I’m assuming you have bearing problems and you are probably hearing a Rod knock. If this is the case, the engine needs a full rebuild or to be replaced.

How much do you charge to do one? I have one that needs to be done.

@blindguysgarage

Ай бұрын

Typically around 700 including oil pump and timing cover gasket set

@timkeener5501

Ай бұрын

Are you near Brunswick Georgia?

@blindguysgarage

Ай бұрын

@@timkeener5501 Winston GA 30187

Where is the part number

@blindguysgarage

10 ай бұрын

The oil pump I use is a Melling m295hv sorry I thought i thaught I added it to then description

@dioniciorosado7763

10 ай бұрын

@@blindguysgarage thank you my friend .i have same truck with same issue 😭😭😭

@dioniciorosado7763

10 ай бұрын

Did you remove the front differential??

@blindguysgarage

10 ай бұрын

@@dioniciorosado7763 no I just took the oil pan bolts all loose and let it drop just a little and that’s it however If you are changing the oil pan gasket you have to drop the front dif

@blindguysgarage

10 ай бұрын

Your welcome any time