I had a outdoor commercial job for a car wash. The owner only wanted to replace the drivers in speakers that are pre-existing. I ended up buying 30 or 40 Eminence for inch drivers for the job and I couldn't have picked a better speaker. The bill quality was awesome and the sound quality was even better.

I'm really glad I found this video! Especially before I started ordering parts for your surround build as I was going to use another compression driver. I'll have to take a closer look now! Thanks

I've been building custom Guitar Speaker Cabinets since 2015. I use ONLY Eminence speakers. The only time I've ever put in anything else is if a customer specifically requested a certain "other brand" speaker. Eminence speakers are usually cheaper, better built, and offer more options to tailor fit the cabinet build and sonic pallette. Can't beat them!!

@juliobello4561

2 жыл бұрын

I play bass and eminence is brand that my dad always love in his gear and PA gear.

@Davidthestratman7

2 жыл бұрын

I build speaker cabs lol. So much cheaper and I think they sound better lol. In your opinion which speaker does chimey cleans better for a Marshall?

Their 10s in a 610 bass cab I had were awesome. Took 2400w like a champ with clean distortion if I did overdrive them a bit. Very nice mids.

I own 3 of the N314-X TexTreme drivers that you mentioned, and they are incredible, fully recommend!

Great variety of drivers and products to play with, and getting 100% of the time good results. PRV too

Beta 10 CX LCR project going well. Just need to build the center channel. The 10 CX + ASD1001+ Eminence 2,500Hz crossover with L-pad sounds really good. 1.85 - 1.9 cu.ft. tuned to 53 Hz.

I've built some home theater and open baffle speakers using their stuff. Very happy

Definitely an Eminence fan here. My mains each have a Delta Pro-12A in them and they are sweet for every db of their range. The trick is, using them with enough power to make those rigid surrounds and cones move. They will thump you to your core. These are very powerful, clean, professional drivers. I can't imagine even wearing one out over decades of residential, non-professional use. I would like to see more DIY builds with these. A 3-way with an 8" Eminence woofer would be nice, and would still be a ridiculously potent speaker in a residential setting.

@juliobello4561

2 жыл бұрын

I bet when I practice I only used small amp with pair 10s eminence and I have to crank the bass down I feel the walls rattle lol . I’m on project fixing my SWR 4x10 anyways I never thought of using them at home but now I’m curious how sweet they must sound with music and movies 🎥

Agreed, I have them in my 64' Impala and my Nissan Titan. And I have 4 6.5 tang bands in a custom box for my subs. Purely amazing. The guy that installed my system was a retired general motors engineer...

I have the little Fender Bassman amp with a single Eminence 10 inch speaker. It has more bottom end than my old Peavy combo with a Black Widow 15 inch. Impressive little speaker!

Years back i had a set of WLM speakers (Aura active and Duo 18) They used Eminence except for the hf - price tag on those in Usa must have been at least +1800 Usd. There was alot of engineering involved (phase coherent - active filters etc) and they sounded incredible ! Pure high end with the Umpf Pro speakers can give you. I cant remember the exact tranducers used but it was not the extreme ones, that tells you Alot abot Eminence.

Really enjoy your videos and always learn something. Wonder if you would do a video on speaker measurements showing people how to produce the graphs as in your video. Measuring bass is the area I struggle with the most. Fine from 200hz -> gated.

I built a diy “superscala” with a pair of kappa 15c in them, and oh lord are those drivers good. It doesn’t even matter what amplifier I slap on them, it just sounds so sweet whether it’s an 500w 4ohm a/b amp or an 11w tube amp.

I've been using Eminence OEM replacements since the 90's for mobile dj's, bars and nightclub sound systems.

I built several speakers and only used Eminence drivers in them with excellent results and only had one driver bad out of the box (something rubbing and sounded terrible) they replaced it and all is well love these drivers.

Great to see they are still made in the usa quality speakers so many once well known brands making their stuff in china .

Yes, I also love Eminence speakers in a guitar combo/amp/cabinet.

I've been a speaker manufacturer for nineteen years. In my experience the actual performance of Eminence drivers matches their data sheets better than any other manufacturer I have used. Including some that are a LOT more expensive. The N314X Textreme compression driver mentioned in the video is superb, and that little Beta 10CX coaxial is crazy good, not even taking into account its low price.

Eminence is absolutely a great company. My best matched drivers came from them and another from Denmark. Loved them both.

Love eminence drivers... and their coax design! You'll love those for surrounds. The Volt 10s are super detailed. Outside of diy sound group, you don't see a lot of eminence being used for theater speakers, at least I haven't.

@Toid

3 жыл бұрын

It's true. And I'm not really sure why. They're perfect for high efficiency home theater builds. Which honestly, I think more people should be doing.

@TheTrueVoiceOfReason

3 жыл бұрын

Hey Summiteer! I've seen Eminence around for a large part of my life - Musician types, Pro Audio, Electronics catalogs back in the day... Got my eye on some to go with the subs from Nick (Toid).

@joee374

3 жыл бұрын

Eminence drivers are used in IMAX theatres!

@LifeofBliss

3 жыл бұрын

@@joee374 i meant in the diy scene. They are all over the place in the professional world like Nick said

@joee374

3 жыл бұрын

@@LifeofBliss Ohh right i see what you mean. True they do make incredible drivers, should be used more! Currently using 2 LAB12s, nothing compared to ur hs-24s 😍 but they are very good

What software did you use to measure the speakers and to make that chart showing how well they were matched?

Great break down of their products. I just ordered 2x Kappa 10 Pros.

@ArchangelMicheal-vk6jm

3 жыл бұрын

You won’t regret it..

JBL used to make drivers in California. Misco Speakers in Minnesota still makes a lot of speakers in USA. They have also merged with a lot of other US companies.

I plan to buy a black mountain very soon for home speaker, it should very good vocal but worries about low frequency.

10/10 Need to collab with Jerry

@Toid

3 жыл бұрын

That would be awesome!

Eminence is also the OEM supplier for many guitar and bass guitar amplifier manufacturers.

Just down the road from me ! Alot of Kentukians are audiophiles and utube reviewers lol Tekton !

i agree with Toids on this brand, i been on business with eminence since 98, great products with great prices, since the box to the glue they use is all american price quality, this speakers last forever and the curves they show is exactly the actual response on the component, still until today sperb company..

I made pair of speakers 10 years ago. Two way with eminence beta 12lta and super tweeter apt 80 used every day, plus svs sb 1000 for lower bass

@Toid

3 жыл бұрын

Nice! What did you think of them?

@Artevaldo

3 жыл бұрын

@@Toid Nice sounding, very good quality, those speakers just sound different. Pross no need powerful amp, nice vocal, strong mid. Cons lack of bass, bass hard.. I prefer deeper bass. I changed eminence beta 15a sub to svs sb 1000, because svs is much smaller and goes deeper. Overall beta 15a to my years is better for bass, there is no replacement for displacement . Work well in large rooms. Good price -quality ratio. In those ten tears never thought to replace it..

@rmlora6tt133

3 жыл бұрын

I made a pair of bookshelves using the kapa10s I think, with prvs Twisters no crossovers, just the protection cap on the Twister! And even my kids love them, don't remember last time that we used my 9.2 setup after those eminence are on top of my klf30s on the living room!

Speaker made in the USA means quality assured. Eminence speaker company is an esteemed organisation.

Ever heard of klh? They make damn good sounding speakers

Will those 10 inchers you have been sent compromise Beveridge Model 3 Electrostatic Audio Transducer musical instruments?

Where can I order their parts for example magnet,coils, paper cones and so on

I own, eminence kappa pro 15A x2pcs, psd2002-8, kilomax 18proA, definimax 18, kappa pro 10A x6pcs very clear sound

Are the beta 12a good to make towers similar to what you did,those large towers you made I mean?

We need a 6.5" woofer and 1" tweeter combo for a build.

@sunilcherianpullockaran8817

3 жыл бұрын

Peerless woofer BC18WG59-04; BC18WK05-08; SDS-160F25CP01-08; SDS-160F25PR01-08; and Peerless Tweeters DX20BF00-04; DX20BF00-08; XT25TG30-04. If money is no object then Woofer HDS-P830990 with tweeter DA25TX00-08. Drive units arranged in order of ascending cost. I am an Orthodontist by profession but into designing speakers and crossover networks for the past 30 years and designing cross over networks is my passion. Of the lot Peerless manufactures the best drive units when cost is taken into the equation and more importantly they can be matched for phase and frequency with just 4 electronic components, which is difficult in the case of Morel and the rest of the gang. To get parts at 1/3 cost compared to parts express head over to components-center, but I have not factored in shipping costs. Good luck with your build. When designing the cross over network make sure that you spend as much on the cross over network as you would on both drive units of one box. Do not skimp on the cross over network and phase matching if you want a wide sound stage and realism that makes the speakers disappear.

@sunilcherianpullockaran8817

3 жыл бұрын

This is a reply to MAD GRUMPYMAN who asked clarifications on why coaxial speakers with a single component crossover crossing over to a tweeter, sounds good in automobiles. Well the answer has to do with ambient sound and how forgiving our ears are. The most silent a car is going to get, even if you own the Flying Spur is going to be at the bare minimum 56dB and the Rolls Royce Ghost is at 54dB. Whispers are 41dB and quiet means about 28dB. Do also note that the dB scale is logarithmic. Noise introduced by speakers, cables, crossover network components or amplifiers of average build means zilch in automobile audio. Sound stage is insignificant since the speakers are placed all around as in a home theater. If you want to melt the speakers away with impeccable sound stage then it has to be two channel audio amplifier with single voice coil in each speaker(full range driver) so as to do away with crossover network all together which means coaxial speaker drive units. Unfortunately physics and the cilia in our cochlea(audio pressure wave to electric converter in the cochlea of the ear) do not play ball. As a compromise one has to have 2.0 system at the bare minimum with a mid/woofer and tweeter in one speaker box with a cross over network and if one can afford it a 2.1 system crossed over at about 40Hz with a dedicated amplifier for the subwoofer if one listens to classical music or electronic dubstep but then the cost goes into the 30,000 dollar levels for the system. The single electronic component in a cheap car audio cross over network is usually a 2.5, 4 micro-farad bipolar capacitor. It functions to roll of electrical current to the tweeter below about 6000 Hz which is one hell of a compromise because the mid/woofer will likely have cone break up and peaks, above 6000-8000 Hz depending on the cone material. Interference between the speaker drive units in one box will cause peaks and troughs in the output but our ears are very forgiving to change in amplitude as long as it is consistent. I hope you know that humans above the age of 55 can barely hear anything above 12500 Hz anyway. As age advance harshness is the one sound attribute that humans cannot tolerate and all else is forgiven or not even discernible which is why high end valve audio sounds so good. Sound stage is the holy grail for good audio reproduction for older people and which is the most difficult thing to reproduce faithfully with the least number of electrical/electronic components. On a side note do you know that the silencer assembly (from exhaust port to exhaust tip of automobiles is the most difficult thing to design in a naturally aspirated automobile and which is what ricers meddle with first, by changing the endcan and the tube diameter. Similarly the cross-over network is the single most difficult component to design in loudspeakers especially when the aim is minimal crossover components and which is what speaker manufacturers skimp on. For good sound stage you just have to spend through your nose, no two ways about it, even if you have just 4 components in the cross over network. Super high end audio matches not only the drive units but also the speaker pair just like dampers erroneously called shock absorbers come in matched pairs as do tires of a single axle in race cars. Well I am veering off topic. Bye.

Music is something very complex....even more, when we are talking about (speakers)! How many times Have I heard that some woofers sound absolutely terrible....until I proved otherwise! Yes, I did it and I even went beyond whatever I heard from the greatest audio engineers because I knew that something was wrong! So one day I decided to buy a pair of 2 12 inches woofers and to build some speakers based on a pattern that I made that gives an incredibly deep and rich bass! You just can not imagine the face of the people who listened to the results! I showed them that all it takes is a nicely built and tunes cabinet with a port placed at the perfect place! I wish I could tell you more but I just can't give up all that I've been working hard for years and see the credits being taken by someone else!

I love there horns

I’m restoring my cabinet SWR Goliath the old eminence are getting upgrade wanna try neo 10s

In the UK there is better value for money due to shipping but the actual drivers are quite high in quality. I'm not sure vs Precision Devices, Faital Pro and B&C but they are pretty good if you limit them properly. The kappalite bass drivers are very efficient but need a larger than normal box to get the most out of them. I'm using 3 cubic feet or more for a 12 tuned to 40Hz. For the 15 it's 2 x this for the same performance but 3dB more efficient. They even did custom drivers for companies like Barefaced - with performance of the 3012LF and 3012HO rolled into one.

Sounds great. Out of my price range.

I have two, 15inch Kappa pro LFA, pls suggest enclosure (vented) size with tweeter....

"Good on yer, mate!" for giving attention to sample-to-sample consistency. IMO this is a key to great multichannel imaging, especially in the time domain, yet some prominent disciples of Toole insist that every meaningful speaker measurement can be taken from a single sample. These same folks even listen-test a single speaker and think that some delocalization of its perceived sound source is a virtue. I can't help thinking that would be a predictor of a smeared image when 2 or more channels are in play, annoying for music and fatal for cinema. Keep up the good work!

This is a reply to MAD GRUMPYMAN who asked clarifications on why coaxial speakers with a single component crossover crossing over to a tweeter, sounds good in automobiles. Well the answer has to do with ambient sound and how forgiving our ears are. The most silent a car is going to get, even if you own the Flying Spur is going to be at the bare minimum 56dB and the Rolls Royce Ghost is at 54dB. Whispers are 41dB and quiet means about 28dB. Do also note that the dB scale is logarithmic. Noise introduced by speakers, cables, crossover network components or amplifiers of average build means zilch in automobile audio. Sound stage is insignificant since the speakers are placed all around as in a home theater. If you want to melt the speakers away with impeccable sound stage then it has to be two channel audio amplifier with single voice coil in each speaker(full range driver) so as to do away with crossover network all together which means coaxial speaker drive units. Unfortunately physics and the cilia in our cochlea(audio pressure wave to electric converter in the cochlea of the ear) do not play ball. As a compromise one has to have 2.0 system at the bare minimum with a mid/woofer and tweeter in one speaker box with a cross over network and if one can afford it a 2.1 system crossed over at about 40Hz with a dedicated amplifier for the subwoofer if one listens to classical music or electronic dubstep but then the cost goes into the 30,000 dollar levels for the system. The single electronic component in a cheap car audio cross over network is usually a 2.5, 4 micro-farad bipolar capacitor. It functions to roll of electrical current to the tweeter below about 6000 Hz which is one hell of a compromise because the mid/woofer will likely have cone break up and peaks, above 6000-8000 Hz depending on the cone material. Interference between the speaker drive units in one box will cause peaks and troughs in the output but our ears are very forgiving to change in amplitude as long as it is consistent. I hope you know that humans above the age of 55 can barely hear anything above 12500 Hz anyway. As age advance harshness is the one sound attribute that humans cannot tolerate and all else is forgiven or not even discernible which is why high end valve audio sounds so good. Sound stage is the holy grail for good audio reproduction for older people and which is the most difficult thing to reproduce faithfully with the least number of electrical/electronic components. On a side note do you know that the silencer assembly (from exhaust port to exhaust tip of automobiles is the most difficult thing to design in a naturally aspirated automobile and which is what ricers meddle with first, by changing the endcan and the tube diameter. Similarly the cross-over network is the single most difficult component to design in loudspeakers especially when the aim is minimal crossover components and which is what speaker manufacturers skimp on. For good sound stage you just have to spend through your nose, no two ways about it, even if you have just 4 components in the cross over network. Super high end audio matches not only the drive units but also the speaker pair just like dampers erroneously called shock absorbers come in matched pairs as do tires of a single axle in race cars. Well I am veering off topic. Bye.

I was waiting for a video after the video commercial

I wanna hear the new Dv-77. I guess they're their new modern metal speakers. Btw, WGS is american too and the Reapers and Retro 30's are pretty badass 👍

@Toid

3 жыл бұрын

Good to know. I'll have to check them out. Thanks for the tip!

@jaychen2000metal

3 жыл бұрын

@@Toid Yeah man, i got 2 Retro 30's and 2 Reapers. Can't complain.

Yes definitely make some good drivers isn't that what tekton use in their speakers. What would work better in the coaxial driver setup is changing the mount, is it steel or aluminium? I would make the mount out of Birch or mahogany, you can get wooden pulp that you can use in 3D printers have you got access 3D printer, you make it out of that would be good! and inserted epoxy it into a brass tube thread. Cut down a lot of resonance give it a go let me know how you get on. Put a brace as well in the cabinets and with same Blu-Tack so the tweeter magnet is pushing against it

IDK, its hard to beat celestion alnicos, an EVL12 for modern metal and a Jupiter alnico for vintage tones. Competition is good for us guitarists.

I think it's funny that Eminence is better quality and the same price or cheaper than Celestion's since Celestion has moved from the U.K. Having said that, Celestions newer speakers seem to have quality even though they seemed to drop it on some of their classics.

Live in Kentucky, been here all my life, only 46 years, never heard of this brand. Must not be in the car audio market. I remember a company named "Volcano" made here as well. Hold the phone... A man is really named "McNutt"? FML

Hey bro ever heard of these Vintage Omega AP Speakers 3 Way USA Model 150 ?

Also Stereo Integrity makes subwoofers in USA

Toid could you point me in the direction of the anatomy of a speaker driver. What would make one manufacturer's 6-inch driver produce a low-frequency response of 40hz while another 6 inch only goes to 50hz as an example?

@DJ_Force

2 жыл бұрын

A speaker is basically a cone on a spring. The firmer the suspension and the lighter the moving mass, the higher the natural vibration of the speaker. A speaker with a lose suspension and heavy cone/voice coil will naturally vibrate at a lower frequency than one with a tight suspension and a light cone/voice coil.

@bellrobert1978

2 жыл бұрын

@@DJ_Force Thank you.

@frankstetka7206

2 жыл бұрын

Also the efficiency has much to do with that mass, magnetic field - gap at voice coil and how tight that suspension is so we can find 3” woofers designed to produce lower frequencies than 6” drivers but at much lower effectiveness. We can also find a 6” midrange which is extremely efficient by comparison to a 6” woofer or subwoofer. Another interesting thing to consider is how a speakers individual components sum up if it’s best used in a sealed or ported box or even open baffle where it has no box at all. Many car speakers are essentially geared at infinite or open baffle otherwise they would suffer mechanical damage if the suspension parts were made for a sealed cabinet for example. Blah blah 😆 fun hobby, the sky is the limit for creativity and how much time and money one can spend. Eminence has been pretty old fashioned design wise until most recently, great quality but generally low tech and sometimes unfavorable midrange spikes in the response curve in the pro driver lineup and this is why they can claim a very high efficiency rating. - good for a stage monitor and not a reference system

That LAB12 gets no credit. No one wants the LAB at a shootout.

@frobernal

6 ай бұрын

I love my lab 12s. Probably the best sub I've ever used.

So what other pro drivers have you tested?

@Toid

3 жыл бұрын

Quite a few. Some off the top of my head would be Faital Pro, Dayton, JBL, PRV, peerless, Eminence and I am sure more that I am not thinking of right now.

Funny you should mention... In investigating the feasibility of a high efficiency speaker system Eminence drivers are leading the way in the bass drivers (Beta 15A). If I didn't already have a pair of JBL 075s they would probably be a real contender on that end too. I am glad to hear the quality is there. P.S I used one of their guitar drivers in a project many years ago.

Curious whether Visaton would be so nice and send you some samples.

@FSXgta

3 жыл бұрын

It seems like Visaton uses old photos ay least on my local store. That kinda puts me off

@Toid

3 жыл бұрын

That would be cool

@SianaGearz

3 жыл бұрын

@@FSXgta Well they also make old drivers. Most of them haven't changed in 20+ years, but given they were pretty decent to begin with, this might not be a bad thing. One of those slow traditional companies. But i didn't find myself desiring them either.

They're getting harder to find, at least those made for guitar amps. Anyone know of a retailer that carries the full line, or at least most of it? Thanks in advance!!

Nick, What driver was it they sent you?

@FSXgta

3 жыл бұрын

Beta 10cx. He said it in the video

@Toid

3 жыл бұрын

Dave they sent me the Eminence Beta 10cx bit.ly/beta10cx and the F110M compression driver bit.ly/2HpGbCc

Well... Are Eminence speakers made in China? In addition to our Eminence, KY facility, the Eminence Dongguan factory is an integral part of our expansion into the global world of manufacturing. It began as our effort to provide our customers with a respected brand of quality loudspeakers in China.

Why are they all listed as Guitar speakers?

Eminence make for alot of name companies

@Toid

3 жыл бұрын

They really do. I don't think many people know how many OEM products they produce.

@altops4490

3 жыл бұрын

@@Toid their lobby wall shows 3 dozen or so companies

Learned a few months ago that they are not being made in the U.S. anymore.

It’s true I have seen Open enthusiast swear by the eminence Alpha 15

LOL. Paper pulp is "special" because it's from old American trees. But Chinese magnets are "just magnets", and "magnets are magnets". I thought you can't get snake oil anymore. Snake oil is just snake oil. But the people selling it are "special".

@frankstetka7206

2 жыл бұрын

No magnets come in all different forms and he even mentioned specs. I did find it amusing about the paper pulp comment but that is important also, just ask guitar players who won’t use the Chinese Celestian units and are in favor of the British cones.

Problem is they have a horrible reputation, they have made drivers for hundreds if not thousands of bad sounding speakers. Reminds me of this high end audio place I went to in the 90's, like many they allowed you to trade in your old gear for upgrades and they had a room filled with just Klipsch speakers people returned, the expensive models. One guy was doing that while I was there, he actually downgraded to a NHT superzero surround sound system and said it was vastly superior.

I like svs subs

Anybody here know where i can find good quality made in usa car speakers? Thanks!

@frankstetka7206

2 жыл бұрын

I don’t think anyone manufactures them in the USA however many are actually designed here; of course you can always use Eminence pro drivers in an automobile but not in a traditional set up so be prepared to modify the automobile to suit.

Did you build the surrounds?

Some American made speakers are made in Canada.

B&c blows Eminence out of the water with quality but don't forget radian

@daviddrake6875

3 жыл бұрын

They had a fabulous 15 inch 4 OHM 99 DB efficiency Free air Resonance of 16Hz was used as bass speaker in horn section of Speakerlab K. Fantastic but they don’t make it anymore.

@CravingTheMagic

3 жыл бұрын

@@daviddrake6875 it's sad how company reputations have gone down hill only now Eminence releases the tour grade series. I have the 314t and really like them

Your tone of voice gave it all away....

I have absolutely nothing against Eminence. But who said those two drivers are not a matched pair from the same batch?

@Toid

2 жыл бұрын

You're right. They could have matched them before being sent out. But the packages weren't previously opened, so I have no reason to believe they were. But you're absolutely right, they could have been.

@frankstetka7206

2 жыл бұрын

I would in the least presume they are from the same batch or production run

How much did they pay you?

I wound if see professional dj sperker made for like scoop cabi an other .

If you would see what my friend can make in China - your eyes would pop out, SB is piece of junk beside them, even the Satori are nothing special. Let's say you can throw the TB underhung 6.5", you know where. His can do 1" p-p. And not too many companies outside of China have magnetizers to properly magnetize Neodymium. Eminence is OK, too bad they don't make hi-end home drivers.

@Toid

3 жыл бұрын

There are some really good manufacturers in China. Like I said, China gets a bad name but that doesn't mean that all of them are bad.

@FOH3663

3 жыл бұрын

I know what you mean, ... however Eminence does make a superb 21" LF driver, being utilized in high end systems, and it doesn't get much better than that. It's world class and yet retains that affordability that they're known for. It's the NSW6021-6

Lost me at paper cones.. lol

nice, as long as the magnets are not made in communist china, I will buy their speakers, as I'm boycotting everything made there, and for many good reasons. we need to bring back our manufacturing, or else china will surpass us as the world superpower, sooner than later, hopefully their economy completely tanks before then, "made in America" must be our main concern when buying anything, their cheap crap is not worth saving a few $$$... thanks for making this video, I didn't know about this brand, and this is what I've been looking for

Paid ad?

Am I watching a youtube video or am I reading a brochure given to me by Eminence Speakers?

did they pay you to make this video?

@Toid

2 жыл бұрын

No

@Jakeman90210

2 жыл бұрын

@@Toid weird. It feels a lot like an ad. Feels like you're reading from their website, and you're using b roll footage of their factory.

@Toid

2 жыл бұрын

@@Jakeman90210 yeah, it definitely isn't my best video. I had a lot of people claim that it came across as an advertisement. After this video I actually stopped doing videos like this. Instead I invite someone from the company on and let them talk about their products. I definitely don't want you guys feel like I'm trying to sell you on a brand. I guess it partially came across that way, because I really do like Eminence a lot. I really do appreciate the input from you guys. It definitely helps get videos out that you guys appreciate.

Too bad that shitty hat isn't US made. #yanks4life!!!

@crazyndn49

3 жыл бұрын

But past the hat, great review brother. I've been eyeballing their drivers for a minute and may run them if I ever do commit to a home theater build.

@Toid

3 жыл бұрын

@@crazyndn49 funny story. I was headed to a Red Sox game in Fenway on the train. Surrounded by Red Sox fans and I looked at one of the kids standing there. I pointed to my then girlfriend and said just so you know she's a Yankees fan. What ensued next was hilarious. But I ended up having to confess that she was actually not a Yankees fan. Still, a lot of fun.

@crazyndn49

3 жыл бұрын

@@Toid I had the chance to go to a Sox game when I was up there in Boston for my tribe. I went everywhere with something Yankees on everyday just because I'd probably never get the chance again. On game nights, the hate is real, but a normal day? Nah, they don't hold too it as hard. Fun times though.

'murica isn't a selling point for me.

Oh more bullshit - how a magnet is charged is everything - and MATURE AMERICAN TREES? Dude get out of here lol. Stopped watching after that.

@Toid

3 жыл бұрын

A magnet is basically a magnet. It obviously needs to meet the specs, which was said. But you're not going to get a magnet from China and a magnet from America that are going to make the speaker sound any different. And yes, eminence uses mature American trees in their paper cones. Most manufacturers do not use mature trees which does make a difference. You don't have to believe me, you can read all about those statements here. audioxpress.com/article/speaker-cones-fabrication-materials-and-performance

Wantfreestuff

Hey bro ever heard of these Vintage Omega AP Speakers 3 Way USA Model 150 ?