2 years later and you taught me more than my jw could ever explain in three months. I got fed up, looked at your video, sat on the floor with some EMT and just fucking figured it out. I realize how bad communication is for some people and teaching really isn't their forte. Thank you for this video dude.

Thanks for being gnarly and not arrogant like 90% of tradesmen 🤙

You’re teaching style is amazing!

@empoweredkc

Жыл бұрын

That’s is extremely nice for you to say…. Most of the time I feel like a complete idiot😂❤

Dope vid bro. This is probably the hardest part of the electrical trade for me.

@empoweredkc

2 жыл бұрын

Mario... the only way to get go is to run 1000000000 foot of conduit :) It takes time, don't be too hard on yourself. Thanks for follow along.

U make this stuff easy to understand thank you I went to school for it but conduit bending was hardest for me to understand just bc of the measurements equation but I’m good at math it’s just knowing where to make your measurements and how much to take off or multiply by like the backends of 90s new subscriber today !! Thanks for the helpful vids

Thanks! Easy to understand! Hope this channel gets bigger!

@empoweredkc

2 жыл бұрын

Thanks so much! To see it grow I need to publish more consistently for sure, but any shares by you would be massive

You’re a genius bro, thank you so much. Keep making more conduit videos

@empoweredkc

2 жыл бұрын

Too kind of a compliment but I’ll take it. What got you into the trade?

My man with the grounding tails on deck👍⚡

@empoweredkc

2 жыл бұрын

Installing them before the mud ring or drywall makes it so much easier… question do you know the code for when you have to install them?

Thanks for the video. I'm always looking to learn and improve myself

@empoweredkc

2 жыл бұрын

Thanks Adam. Is there something you would love for us to go over?

You’re a goat for this brotha

@empoweredkc

Жыл бұрын

Let’s be honest… the true Goat is The one and only Lebron James aka King James aka MJ fans beware😂 Appreciate the Support❤❤❤

Appreciate the help !

I'll always sub to a new Electricians channel. Subbed and Liked

@empoweredkc

2 жыл бұрын

Thanks and much appreciated!

Hey, I’m studying electrician and this help me too much, thank you man. And I’m learning English at the same time XD.

Hi, I like your video. Thanks

Good job 👏 👍

@empoweredkc

Жыл бұрын

Thank you 👍

Lol. Great channel

Nice video.

@empoweredkc

Жыл бұрын

Appreciate It

Need 5 minutes videos as refresher on a job sight. Anything longer than that we might as well makeout

Good video

Thanks Josh

Make a video on the tape measures

@empoweredkc

2 жыл бұрын

THANKS A TOOOOOOOON for bringing this up. We are actually going to start making "Tool Tips" where we cover tools. This is 100% because of this comment Esteban! Thank you!!!

Very nice bro!!

@empoweredkc

2 жыл бұрын

Thanks, the peeps at intrepid creative make us look way smarter than we really are...

Great job

The problem with air bending is that it's very hard to match bends on parallel runs. It's better to floor bend them. Great video, with explanation. Can you do a video for floor bending?

@danielhady3021

2 жыл бұрын

Just takes time. I prefer to air bend so I'm not bending over all day.

@empoweredkc

2 жыл бұрын

TBH I hate floor bending, the second bend (if not done on a elevated platform) will mess up the first bend. When you "air bend" be sure to hold the conduit as close to the bender as you can. That will help with consistency. ps. I will do a floor bending video and show what I mean. Thanks a ton for the follow and comment.

@empoweredkc

2 жыл бұрын

@@danielhady3021 🔥🔥🔥

@senorjalapeno3937

Жыл бұрын

It's called an hand bender

What about the box offset?

@empoweredkc

2 жыл бұрын

Very small offset.... TBH I usually use Minis instead of one hole straps so I almost never need a box offset. We will cover it though. Thanks!

You should do a video on deep offsets

I need to bend a 30 degree offset in a stairwell but at the bottom it needs to drop roughly 6 inches under the landing of the floor above. Any suggestions on how to make that look good ?

Im currently going to trade school and learning conduit bending. How often do you use boxsets in the field because i noticed you didnt use any here. Thank You

@empoweredkc

Жыл бұрын

Haha almost never. I love using minis which help you keep the conduit centered and straight and eliminate the need for the box offset. I know that there is a time and place for everything so se do have a video up on box offsets. Keep pushing to learn and grow. You’re investing in yourself my friend ❤️

Nice, so you measure offsets from center to center?

Using cm or mm would be ridiculously easier for measuring?

Awesome

why did you subtract 2 inches?

@empoweredkc

Жыл бұрын

I started the bend 2 inches front be end of the conduit… the real question is “why so sweaty?”

It's easier if you just calculate the shrink and pre cut the conduit to length.

@empoweredkc

2 жыл бұрын

The only time I would ever say "shrink" and "easy" together is in a ice bath 😂🤦🏻‍♂TBH the only time I factor in shrink is on saddles. Good point though and you are more advanced than most.

Hey I’m still new to this but aren’t you suppose the measure the offset depth and multiply it with the multiplier

@empoweredkc

Жыл бұрын

Yeah…. For a 30 degree offset measure the distance and multiple it by 2. For a 5” 30 degree offset the marks need to be 10” apart. 5x2=10

I thought it was a 1/4 inch x offset depth

This guy is great! The Music background sucks

How to knew that's the bend you need is 30deg

@empoweredkc

Жыл бұрын

A 30 can get you almost everywhere on a construction site. Make it your go to.

You made the right example but you were kind of wrong because you are bending by using measurements from boxes at the top and center of the stud, which I’m pretty sure you know that boxes don’t go on top of the stud it goes inside because then it would be exposed once it gets sheetrocked so that means that offset should of been at least 1 to 3 inches shorter depending on what knockout you are connecting to in each box, great example though I’m pretty sure the smart ones get the point lmao, but keep doing what you are doing I’m pretty sure it helps a lot of people

@eloyvillarreal3927

Жыл бұрын

Unless it’s an opened wall but I doubt it usually walls are covered

Or instead of center to center measurements, do outside of knockout to inside of knockout 🤷‍♂️

lower the background music a little.

"Founder and master" don't hurt your shoulder patting yourself on the back

@empoweredkc

11 ай бұрын

I would’ve said “entrepreneur and electrician,” but I can’t spell those words without auto correct.

Josh - Fire your video editor. Not just for the awful intro music, but for not editing out the entire video

Bro. You're an 1/8 away from 15" lol