I love how he's got to put his safety goggles on before he explains anything😂😂

Now the "bat-a-rang" can be cut with sharp edges😁😉

@nanaki-seto

4 жыл бұрын

heh i was thinking some shape that when cut wont come out of the source material

@AusyG

4 жыл бұрын

Yassss!!

@another1commenter770

4 жыл бұрын

@@1Slamalama1 yip, if they cut a turbine that had a flats on the shaft outer between the blades then it would be lock in.

Still better that 100% of corporate demo vids Yea Im not joking

@benjaminparker4482

4 жыл бұрын

How do you know this isn't actually secretly a corporate demo vid

@SurgeShock

4 жыл бұрын

@@benjaminparker4482 Corporate video to pull you into watching their channel

@F_L_U_X

4 жыл бұрын

Than*?

@n1elkyfan

4 жыл бұрын

@@benjaminparker4482 it definitely is a corporate demo video. Its just they got the waterjet channel to make it. The other thing is it will reach a much larger audience. Even knowing that it's pretty cool.

@GnomeChomsky9999

2 жыл бұрын

It’s how sales works!

No lick test. No throwing stuff against the wall. Come on. Get back to work gentlemen!

@MichiosGraphics

4 жыл бұрын

I'm very disapointed with them myself hah, no Batarang, No Lick test etc. but actual WORK.... Not good guys....

'Diamond Orifice' was my nickname in college. Not sure why.

@F_L_U_X

4 жыл бұрын

Then you were probably a drop-out.

@kleetus92

4 жыл бұрын

Sending or receiving?

You should try making a spoon with the waterjet.

7:42 “That’s pretty accurate” Mitchell: “Uhn guhl whlissis”

The head cutting at an angle looked so cool!!!

@dimitar4y

4 жыл бұрын

Keep that imagination, you'll need it, despite what everyone tells ye.

Does this mean I'm certified to operate the water jet? See you guys Monday!!

@WaterjetChannel

4 жыл бұрын

Well played

Very interesting but how does the lick test actually work? 👅

@rouge5140

4 жыл бұрын

Step 1: lick Step 2: know

@paulstan9828

4 жыл бұрын

Belethor Ha!!!

@Trance_Kitsune

4 жыл бұрын

This needs to be a video ASAP.

@paulstan9828

4 жыл бұрын

Kitsune91 I can see the video now. Cartoon graphics showing the pathway from the tongue to the brain. Maybe like Curley’ brain xray in the old three stooges films. Ha!!!

@Trance_Kitsune

4 жыл бұрын

@@paulstan9828 LOL filled with tons of equations, calculations, etc. across the screen to a bang of light only to show his face "Yep. Its [object in question] confirmed."

wow, it wasn't until this video that I realized how jankety and old the old waterjet looked compared to the new one

Kent huh? That's real close to me! I hope you guys are enjoying the state! My work really needs to get a waterjet. It would make life much easier for our shop. Enjoy your stay!

You guys are hilarious try to be professional but it turns out just naturally funny

Ot was really cool and nostalgic seeing all the old videos thinking, “I was there when that video came out.” Love you guys.

Very informative video on the workings of a waterjet, well presented and a demo of a cut that would be hard to do in one operation and as quickly with other methods... End card suggests I watch Mitchell drink toilet water through a filter straw.

Great job guys. I had a water jet used when I was building the rubber treads for a Johnny 5 robot I built many years ago. The only other option was to have a hard stamping tool made. Water jet was faster and cost less. Fantastic tool.

Interesting! Never a boring video with you guys.

this was incredibly informative, and entertaining. that impeller was really cool

That video was enlightening on what the machine and y'all can do with it.. Did not know that machine was made in my state that is cool....

This is a game changer for the channel and business!!!

How high it gonna be if the waterjet facing upward

@nonec384

4 жыл бұрын

but how high can it go facing dawnward?

@realkushman

4 жыл бұрын

Apparently that's how they got all those craters on the moon

@gingerale6634

4 жыл бұрын

It’s a rather small stream so I’m thinking it would spread out too far for the camera to see?

@dimitar4y

4 жыл бұрын

You can actually easily calculate how high it would be. Water is just like air, it creates drag based on its density. If it went 2.5ft in water, and water's density is ... 997 kg/m³. Air's density is 1.225 kg/m3, so that means it'll go like 900 times higher. So about 2250ft. Probably. But that's oversimplified, since it'll break apart into a mist and get dragged down even more due to the surface area... Which I donno how to calculate that, so like... about a third of that, 800ft? They can't really do it since there's a roof in the way. Maybe if they hack in an extension hose and fire this dangerous thing with a loose waterjet cutter, prefferably bolted down to solid ground.

@SbassLaser

4 жыл бұрын

@@dimitar4y nah since the mass of the stream is so small the air resistance would slow it down considerably since it would break apart into droplets and wouldnt stay in a solid stream. also you'd be fighting against gravity. I'd guess less than 100 feet

I see beveled knife blanks in the not so distant future! Glad you guys had fun, keep it up!

When that was cutting I actually started falling asleep, more please I love it

Loved the video, and enjoyed its extra length oooo yeah

I love how every single shot, Mitchell's safety goggles are off again hahaha

Love your show keep up the good work.

Just wanted to say, you guys are great

How you can tell that impeller is good without lick test?

Watching the waterjet cutting that impeller was amazing. I was so smooth!:::::::::¡)

My manufacturing lab at my community college, has a water jet cutter. It is awesome watching it

Ahhhhh! Awesome, as usual. I need one haha.

Cool machine man, really is a piece of technology. Looking forward to the things you’ll make with it

@BrilliantDesignOnline

4 жыл бұрын

You would not think it was so cool if you had to shovel the garnet out of the tank every 3 months..wet, heavy, soggy, dirty garnet over the edge.

Awesome Presentation ❤

Very cool!👍

I've been waiting for the plank to come back!

you guys should make a video where you make a knife start to finish wood grips and all itd be some great advertisement for waterjet knives

My most favorite job was near Kent Wa. Camp Berachah for life! Hope you guys enjoy wa

BEST CHANNEL EVER

Make a tungsten water wheel and spin it with the water jet like the skateboard wheel

Awesome thanks!

I live in Orange County so that’s actually kinda cool to see that bike

That is so impressive and hard to wrap your head around of the pressure behind that. What doors this has to open up, I'm sure it was quite a breakthrough when discovered... No pun intended...lol

Consumables: garnet abrasive, mixing tube, oriface, table slats, pump piston seal components and filters, water, electricity (tens of kilowatts). That's why they're so expensive to operate.

@dimitar4y

4 жыл бұрын

And the occasional maintenance to clean the tank out :P Hahaaaa, gotcha!

Dude.... 4:40.... why you pointing with your middle finger?? Who does that? 😂😂

Dang it! I actually learned something from you.

Mitchell should lick test the pressurised water to make sure the filters are doing their job

*NEW VIDEO IDEA* You should see how far the water jet will shoot across your warehouse!! Cheers from Eagle MTN, UT

Dang you guys are in my home town!

I remember when OCC made the bike for Flow.

Do a throw back video of all the good times we had with the old one

I trust we've all seen the obvious nickname for the water jet. Historically on television, Flo was seen to be strong and assertive. This sums up The Water Jet. Also it's other nickname as it is The Water Jet of all. Joann of Arc's middle name was Flo. (That's a fact I just made up. )

"I'm glad you asked! this is a water jet!" *silence* lmao his comedic timing is fucking flawless

From impalers to impellers, a waterjet can do it all!

Here's a question. Why are the grates, in the tank, curved?

@jibtripin

4 жыл бұрын

Travis k asking the real questions

@BrilliantDesignOnline

4 жыл бұрын

They are held in by the tension of the bend, and they are not 'twisty'; with a bend they stand up straight as opposed to straight grates which would want to tip over or vibrate.

@travisk5589

4 жыл бұрын

@@jibtripin True that. Me thinks it's to catch the ripples better.

@travisk5589

4 жыл бұрын

@@BrilliantDesignOnline That's an acceptable answer. Thanks

That beat is🔥

Which one does cost more, a waterjet or laser cutter? Not only in terms of investment but also operating costs/maintenance.

@H0ttabych

4 жыл бұрын

laser cutter is a lot cheaper but laser cutter's use is very limited, unlike waterjet

@sheabrown

4 жыл бұрын

Definitely waterjet. They are way more large and complex machines than a laser cutter. Also definitely in terms of operating costs. Lasers only need power, you don't have to buy abrasive, water, replacement heads. Also you don't have to clean out a massive tank of water for a laser every once in a while.

@dimitar4y

4 жыл бұрын

Waterjet parts are pretty expensive. So expensive, everyone only tells you it on a quote. Especially the tungsten nozzle bit. Lasercutters are cheaper in the small scale, just 500$ a tube and they got a long run time. But bigger lasers..... Oof, those are some costs. But they run much longer and are therefore cheaper. Again, hidden behind quote doors.....

Bolt that impeller to a motor through a plate with a hole in it. Feed a carrot through the hole while it is spinning and chop the carrot.

You need to try Altha's Louisiana Cajun while in Kent!!!! it's on Meeker near the train tracks by Burlington Green park.

Try and see how sharp you can cut a knife blank! If its decently sharp and has a decent angle I'll buy it and make a handle and sheath for it that's channel themed

You should do a saw movie Halloween 🎃 special where you cut in half a fake body 😂 and carve some pumpkins

I love water!

Hey thanks for the videos. Can it damage the tank walls with near by angle cuts?

Ayyye yall are where I liveeeeee

6:13 how is a hole that small even made?

@littlebacchus216

4 жыл бұрын

With an even smaller waterjet!

@yunhanluo3295

4 жыл бұрын

an EDM, or an electronic discharge machine, i think. it basically uses electrical pulses to remove tiny amounts of conductive material from things

@gingerale6634

4 жыл бұрын

I was thinking that it was made how they made that one atom thick tungsten rod (or some their metal) by using chemical erosion?

@markussmith3135

4 жыл бұрын

Spark erosion basicaly a Electrical discharge through a rod to the size of the hole you want

@robertasbell824

4 жыл бұрын

Thank you for all for the answers. 😀

thats a cool tap

0:26 seriously thought you were gonna take us towards a bathroom there when you said "let me show you"

do a video where you fill the abrasive tank with random stuff like flour... if you can afford a spare one 😂

@jacko2131

4 жыл бұрын

Fill the 3ft water tank with flour and make a huge loaf of bread.

This is a Waterjet! You can tell it’s a Waterjet, because of how it is.

Well, it’s 4 am and now I know how a waterjet works

Mitchell putting on his safety windshield before speaking every single time hahaha

I was so sure the corner of the impeller was going to cut the crap out of your finger when you did the spin test, glad to be wrong

@dimitar4y

4 жыл бұрын

Waterjets don't make sharp cuts. They do a sandblast finish. Cause they do blast sand. :> But yeah I instinctively winced too. Sharp corners, yikes!

Very impressive precision is there ever going to a micro home water jet going to ba made be very handy indeed for model hobbyist eveb DIY. In theory

I currently have a Mach 200, which I mainly use for cutting marble and granite. But it looks like I haven't mastered the pump system yet

Now they are unstoppable

You know, planking on a motorcycle actually does increase the top speed. Mitchell was actually doing something right! Except the guy that pioneered that did it in a speedo. You know what to do Mitchell

It works with the magic of licks

How much would it cost for you to cut a 3/8" by 8" by 30" piece of aluminium for a skateboard (I don't know what alloy)?

@dimitar4y

4 жыл бұрын

You should be concerned more about the shipping of the item. Waterjets are cheap, a dollar a minute, so a few dollars at most for the entire job... Unless you're dealing with asshole companies that have a "Minimum cost policy" a.k.a. ripoff artists.

god bless dr.hashish

I wonder how often that nozzle need to be replaced. All the water and silica being forced out, must take its tole.

@dimitar4y

4 жыл бұрын

It does. It gets replaced pretty often. Every 50 or so hours of cutting, especially the more garnet you use. That is, if you need the precision. Without precision, it can last 500 or more hours.

I can tell you guys are best friends

did you both ever make the channel logo with a water jet? if not I think it would be a good video idea

I had no idea these could cut at an angle like that, I thought they were just up and down cutters! Can we get links to the things you cut at the end of this video? The rifle and camera lens made me cry, as they're not cheap things to buy 😭😭

I made my own timelapse of the cut by using the playback speed option, DIY timelapse

12:58 You made an impeller but use it as a waterwheel. It should be turning it the opposite direction.

9:08 i got an ad that showed a game where you shoot people lmao

I can hear the intensifier thumping in the background .

@sammyk1155

4 жыл бұрын

The heart of a waterjet

Im interested to know how long the diamond lasts before the orifice is too big for efficient cutting and do you change the pressure according to material and thickness? (old school retired guy!)

Are you able to cut abs or other plastics with the water jet??

What does a "cut" in a waterjet cost in consumables dollar figure wise? Like in a 1 minute cut, how much does that typically cost (not counting your valuable time)?

@Lunch_box

4 жыл бұрын

Depends on how much of the cutting garnet is used tbh

@dimitar4y

4 жыл бұрын

Depends on the material, since that dictates how slow you go, and therefore how much electricity/power/garnet you use. It also depends on the depth of cut, since it takes time to go through the thickness of the material. And it ALSO depends on the precision you need of your cut, as you need to go slower for higher precision and smoother edges. So time = material type * mmSq removed. Also it's not cheap, I think they covered it in a previous video, 20-40$ / hour. Or 0.33$/minute - 0.66$/minute in best case scenarios. But that's mostly inaccurate due to the wear on the nozzle, the jewel and other expensive parts.

@TheAruruu

4 жыл бұрын

guys.... the original question was "in a 1 minute cut"... how difficult it is to cut through something is 100% irrelevant to the question. they just want to know how much it costs to run a water jet with media for about 1 minute. this doesn't really change whether you're cutting inch thick tungsten carbide blanks, or aluminium foil. whatever the answer is, you only need to multiply the cost for 1 minute by the number of minutes necessary to make the cut you want to figure out the total cost, but the original question is only asking about that 1 minute.

@Lunch_box

4 жыл бұрын

@@TheAruruu tldr you are an idiot

@Bread996

4 жыл бұрын

It’s a VERY expensive machine to run. I service these machines. You have to factor in a lot. First all the consumables including nozzles, garnet, water filters, and table slats. Intensifier rebuilds, hydraulic system cooler replacements, and other stressed parts will wear out. All those high pressure lines, high pressure swivels, and distribution blocks wear out a need replacement. They are all stainless steel and very expensive. The pumps and filters on the chiller wear out. The pump and filter on the table drain. You’ll need to buy filters in bulk. The whole tank itself eventually fills up with sediment, and a vac truck has to clean the tank out and dispose of it a couple times a year depending on your usage. Then of course the water, electricity, and labor to keep it running.

Ah got me with that ad at the 9:09 mark.

0:35 nailed it...

Just wondering how many parts of the Waterjet machine you could replicate/replace by cutting them with a Waterjet?

Can you make a comparison between cutting with and without the abrasive

Now u guys need to make a boat propeller and then test it out

Does the grain matter... Cutting along the grain of medium, cross cut, angled cuts?

@BrilliantDesignOnline

4 жыл бұрын

I don't think so. Our local WJ guys can cut through 9" granite and the 0.040" kerf is close to the same at the bottom.

Very good, wearing safety glasses near a 94,000 psi water jet. Because 94,000 psi of water can't cut through plastic safely glasses.

@dimitar4y

4 жыл бұрын

mostly to keep the sand and crap out of your eyes, really.

@dimitar4y

4 жыл бұрын

@@357BlahEn Cut resistant? Safety glasses? Half a second? HAHAHAHHA no. There's no safety glasses like that. Also if a waterjet's pointed at your face, your entire face *is exploding*, big time. You'd need a full face blast shield, not ... glasses.

WHAT CAN A WATER JET NOT CUT ?????? PLZ HEART MY COMMENT I NEED LOVE

Funny how you describe all of the pressures in psi but talk about microns when talking about filters :P For anyone not well versed in US'ian numbers: 94000 psi = 648.1 megapascal :) And 1/1000 inch = 25.4 micrometer

@dimitar4y

4 жыл бұрын

Because the filters's ratings are in microns. And their waterjet, is rated in psi. They just say what's on the tin.

When piercing, how does the machine know it’s Gone all the way through before it starts moving? Or is it just based on a dwell time?

@TheAruruu

4 жыл бұрын

I think it's actually user input. "seek start point and begin penetration" is the first "start", then once it's through the user hits "start" again to begin the cutting operation.

@BrilliantDesignOnline

4 жыл бұрын

With plasma cutting, it is dwell time. With thick enough material, you must pre-drill a start hole.

Are y'all still in Washington?? I live right near that area