Thanks for this video. Really appreciate the step by step guide to repair this. I'm looking after a friend's house and their Ariston dishwasher is leaking on the floor and giving a F02 error when I turn it on. I won't be DIY fixing this one, but at least we know what the issue is.

Thank you very much for this video! I have an inbuilt dishwasher and (at this moment) no problem with the impeller jug. However, I was wondering if there is any way to de-calcify it as a form of maintenance, without dismantling the whole machine.

I'm french, but I understood all your explanations ! It means your video is a success one ! I will try to do that on my Whirlpool, which is out of order :)

i'm getting the same error code on my grundig dishwasher. Would it be the same problem or its a different kind

I'm still getting a f6 error after I've replaced the water inlet valve and the flow meter chamber. Any ideas what to do next?

Great info, thank you so much.

Is it the same repair for a A6 error code on ariston dishwasher?

can you tell me how to remove the heating element on a hotpoint FDYB 10011 dishwasher

Hello,Can you tell me what an A5 error code would indicate on my Hotpoint Ariston dishwasher LDF1231 4E please as it doesn't run for more than a minute or so? regards alan

could you please help me to repair hotpoint ariston dishwasher F12 problem?

Where can I find the video or the link where you explain how dishwasher work, in trying to repair mine.

Thank you

Hi I have an error code F01 on a hotpoint dishwasher but I can’t find any leaks and float is fine can you help

brilliant thx so much, new sub added

I have the same dishwasher only mine is filling up when switched off through the jug chamber

Awesome

Hello, I have a indesit IDL52 and the 1 and 2 lights are flashing, but I have no information of this error on the manual, can you please help me with this?

@How-to-repair

7 жыл бұрын

this will help you www.how-to-repair.com/help/hotpoint-ariston-dishwasher-error-codes-and-faults-diagnostic-fault-finding/

@How-to-repair

7 жыл бұрын

Iam Glad we could help you Please remember to subscribe to our channel kzread.info Remember to Shop with www.how-to-repair.com and it would help us by posting the video or website on your timeline. This helps us a lot and if we really helped you can always buy us a beer how-to-repair.com/help/buy-paul-a-beer/

I’ve had f02 flash up on my hotpoint dishwasher fdfao32112 do I’ve just went and bought part is it easy to fix

@ericabroughton3520

Жыл бұрын

can you tell me the part please I have the same fault

3

never seen such an over engineered water spout...

Tem avaria A12

Is it the same for F5 code repear?

@How-to-repair

4 жыл бұрын

sorry for delay when you have a technical question please use our site for 24 hour response www.how-to-repair.com/help/contact-us/ Iam Glad we could help you. If you ever need help please use our site for 24 hour response www.how-to-repair.com/help/contact-us/ If have a question please use our site for 24 hour response www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel kzread.info Remember to Shop with www.how-to-repair.com and it would help us by posting the video or website on your timeline. This helps us a lot and if we really helped you can always buy us a beer how-to-repair.com/help/buy-paul-a-beer/ Please remember to mark us to your favourites also I would be grateful if you would subscribe to our channels social media as this really helps my site and keeps us going. KZread. kzread.info Facebook. facebook.com/how.to.repair.appliances

@michaelevans9785

4 жыл бұрын

F5 is number 1 and 3 LEDs flashing and indicates, according to the manual your machine has a blocked filter. The reality is it may not be a blocked filter at all, as was the case with my machine. the filter was always perfect and rinsed out regularly. And it may not be any faulty components either - as was the case for my machine. The trigger for the code is a lack of pressure change at the low pressure switch. The low pressure switch is mounted on the side of the machine frame and connected to the wash chamber by a long rubber tube. After turning on, the machine goes through a drain cycle pumping out any water/fluid that might be in the wash chamber before starting the initial fill. Then the drain pump stops and the solenoid opens to allow the machine to fill. My machine would drain, fill and then stop with LEDs 1 and 3 flashing. I could reset the machine and it would do the start up perfectly as above and get to the same point and stop. I removed the high pressure switch and low pressure switch and both were working fine. I applied air pressure to them and the electrical contacts closed. I put it back together and it still would not get beyond the end of the initial fill stage. There is one hell of a lot of unhelpful advice out there ! I wasted many, many hours. On one site someone stated that they had observed the fitter remove the pressure switch and blow into the tube before charging him for a new switch. I pulled the pipe off the low pressure switch and did the same. The machine now works perfectly. Obviously there was something modest blocking up the pipe. The machine had not been used for a couple of months before the failure so something must dried out and blocked the pipe. The pipe just traps a column of air. As the water level in the chamber rises, so it compresses the air trapped in the pipe. This very small change in pressure causes the switch to throw and informs the control system the wash chamber is now full to a suitable level. Doing the final repair, removing the pipe and blowing into it and then refiting it took me 3 minutes. F5 on the Hotpoint Indesit maintenance system is rarely mentioned and although I visited around 50 sites, the minority that did mention it all just referred to blocked filters. At one site a fitter advised that it could be a faulty pressure switch but did not help by advising which switch and how to identify it - so that is why I ended up testing both. how-2-repair.com do great videos but in the other video detailing all the fault codes they simply waltz passed the F5 and ignored the guy asking the question in the comments - what is it. So I am going to post up this comment in a couple of other places as well, so no one else has to waste quite as much of their life as me finding out they don't need to pay a fitter £70 call out for a new pressure switch when the fix is so easy.

@leelee-gy8er

2 жыл бұрын

I would like to buy you a drink. All fixed for now. Thanks

@dickonprior

Жыл бұрын

Frustrating… @michaelevans9785 Code F06 on my Hotpoint dishwasher led me to replace the impeller jug. All worked perfectly for a couple of days. No more code F06, beeping or dishwasher flooding the floor. Now I am having error F05 when I start a cycle on the dishwasher cycle - it kicks in after the first two minutes. I've cleared the error on one occasion by chucking a kettle of boiling water into the washing machine but now this won't work. Any ideas as to what the problem could be? Might I have knocked one of the pressure switches when I was replacing the impeller jug? Thanks!

@dickonprior

Жыл бұрын

To add to the above - the dishwasher is definitely draining. A quick check outside where the water outflow goes into mains drainage confirms this!

its a new machine i get f02 error code

Hotpoint FDD914 fault A11

Good morning,Siri want send you my dishwasher vedio