오늘도 수고하셨습니다 ~

@MotorcycleRepair

10 ай бұрын

블랙와인님 댓글을 남겨 주셔서 감사드립니다.😄

it's very fun to watch other mechanic from abroad handle the bike, keep good work🙏🙏

@MotorcycleRepair

9 ай бұрын

Thank you for a good look. I will upload it diligently. 😊

감사합니다.

@MotorcycleRepair

10 ай бұрын

김명인님 후원해 주셔서 감사합니다. 😍

1등 ㅎㅎ 오늘도 좋은 영상 감사합니다 🙏 💕

@MotorcycleRepair

10 ай бұрын

빠르게 댓글을 남겨주셔서감사드립니다. 🎉🎊🎉🎊

잘보고갑니다 !! 비전 오너로서 비전 관련 영상 올라오는건 다 챙겨보고있습니다 ㅋㅋ

@MotorcycleRepair

10 ай бұрын

감사합니다. 열심히 하겠습니다. 😄

@doraiyo

5 ай бұрын

비전 좋나요?

뒷라이닝도 언능바꿔야겠어요ㅎㅎ

@MotorcycleRepair

10 ай бұрын

댓글을 남겨 주셔서 감사합니다 😊

8미리 볼트 빠지는 찌잉 찌잉 소리가 너무 듣기 좋네요.

@MotorcycleRepair

10 ай бұрын

기계 소리가 좋으시다니.. 기계 정비 쪽으로는 나아가시면 크게 되실 분 같습니다. ㅎㅎ 😄

비젼 구동계 볼트조일때 토크값점알려주세요

대박...

@MotorcycleRepair

4 ай бұрын

😄

Thank you for the upload

@MotorcycleRepair

10 ай бұрын

Are you properly managing other consumables? I don't know. However, when we checked various things that day... it was confirmed that there were no other major problems. 😄

물론 낡긴 했지만 6만 키로는 정말 놀랍네요.

@MotorcycleRepair

10 ай бұрын

그렇쵸...믿기힘든 키로수 입니다. ㅎㅎ

6만키로 동안 구동계를 안갈았다고요 ? 대박 ㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋ

@MotorcycleRepair

10 ай бұрын

😍😍😍

벨트는 오래되면 고무 경화돼서 수명 짧음. 벨트 교체할 땐 제조년월을 꼭 확인.

@MotorcycleRepair

8 ай бұрын

좋은 정보 감사합니다. 😄

궁금한게있는데 뒤에 클러치도 분해를 해야하는건가요

@MotorcycleRepair

9 ай бұрын

문제가 발견 되면 분해 후 크러치 웨이트를 교체하거나..또는 클러치 전체를 교체하기도 합니다. 그렇지 않으면, 그대로 다시 조립하여 사용합니다.

영상에서와 같이 교체하면 비용이 어느정도 될까요??

@MotorcycleRepair

10 ай бұрын

일반적으로 12만원 정도면 가능하다고 하시네요

A cuantos kilometros se recomienda cambiar la correa 25.000 kilometros maximo?

@MotorcycleRepair

9 ай бұрын

Se recomienda cambiar la correa (al menos 25.000 - hasta 30.000 kilómetros).

정품벨트 품질이 뛰어나다는것이네요..고무속에 나이론원단이 들어가 있어서 갑자기 끊어지는 일도 없을것 갔아요..저도 갈려고 3만키로에 뜯어봤더니 멀쩡하네요...

@MotorcycleRepair

10 ай бұрын

아 ... 이렇게 오래도록 쓸 수 있는 경우가 더러 있군요... 좋은 정보 감사합니다.

2021년 표준 CVT Roller Honda Vision 110은 몇 그램입니까?

@MotorcycleRepair

8 ай бұрын

죄송합니다. 개당 몇그램이나 하는지는 확인을 해보지 않아서 모르겠습니다.

@robertfronda8914

6 ай бұрын

15g standard. Roller size is 20×15 same with pcx.

Any Daelim XQ250 videos, sir?

@MotorcycleRepair

10 ай бұрын

I'm sorry. No video has been shot yet for the Daelim XQ250.

@petiperspektif1890

10 ай бұрын

@@MotorcycleRepair I’ll be waiting, then! Cheers from Malaysia!

@MotorcycleRepair

10 ай бұрын

@@petiperspektif1890 You're from Malaysia... Thank you for your interest in my video! 😄

Why you replaced the drive face? I thought you never had to replace that just the rollers.

@MotorcycleRepair

7 ай бұрын

If the drive face is not particularly worn, you can just replace the weight roller... In the video, since it is a delivery motorcycle and is operated in a very harsh environment, it is replaced with a set. Normally, it would be good to replace the drive face set and belt, but... Depending on the condition, only the rollers and belt may be replaced.

Can someone make an equipment list? Which Drill wattage will do and all of the sockets etc.

@MotorcycleRepair

7 ай бұрын

The tools usually required are 8, 10, and 12mm box sockets, an electric power tool that uses an 18v battery, and a +driver. If you are prepared, you will be able to work.

@HOOKZIE

7 ай бұрын

@@MotorcycleRepair much appreciated. The task was well demonstrated in the video. 👌🏿

@MotorcycleRepair

7 ай бұрын

@@HOOKZIE Thank you.😄

@HOOKZIE

7 ай бұрын

I think I'm going to go for an impact Driver for loosening nuts. And a Toque wrench for tightening. Basically for loosening I'm trying to decide between 18v-20v impact driver or Impact wrench. Does it matter for loosening nuts?

@HOOKZIE

7 ай бұрын

Im going with the DeWalt DCF887 18V XR Cordless Brushless Impact Driver

무브볼... 선한참넘은것같은데 저상태면 운행할때 상당히 불편했을것같은데 진짜 무딘 라이더인가보시네

@MotorcycleRepair

5 ай бұрын

영상을 시청해 주셔셔 감사드립니다.

Dzień dobry z jaką siłą Nm dokręca pan śruby wariatora do kymco new downtaun 125 cm. Albo do innych tego typu 125. Bo widzę że używa pan klucza pneumatycznego. Chodzi mi o bezpieczną siłę podaną w Nm dla klucza dynamometrycznego. Pozdrawiam z Polski.

@MotorcycleRepair

10 ай бұрын

Dziękuję za obejrzenie mojego filmu z dalekiej Polski. Zapytanie... Wartości momentu obrotowego układu napędowego Kimco Downtown 125 są następujące. Strona ciśnieniowa układu napędowego nakrętka czołowa napędu koła pasowego określony moment obrotowy. Moment obrotowy: 5,5 ~ 6,5 kgf-m (55 ~ 65 Nm) tył układu napędowego zewnętrzna nakrętka sprzęgła Dokręcić nakrętkę określonym momentem obrotowym. Moment obrotowy: 5,0 ~ 6,0 kgf-m (50 ~ 60 Nm) Powyższe wartości momentu obrotowego są danymi starymi, Ponieważ nie ma danych dotyczących nowych motocykli, nie znamy wartości momentu obrotowego nowych motocykli. (폴란드어)

@bazejjanuszkiewicz8648

10 ай бұрын

Dzięki za odpowiedź do usłyszenia jeszcze kiedyś.Pozdrawiam.

@MotorcycleRepair

10 ай бұрын

@@bazejjanuszkiewicz8648 Thank you for your interest in my video. 😄

@bazejjanuszkiewicz8648

10 ай бұрын

Jeszcze mam jedno pytanie jeśli można interesuje mnie siła podana w Nm od przedniego i tylnego koła dla Kymco downtaun .Z góry dziękuję 😃

@MotorcycleRepair

10 ай бұрын

@@bazejjanuszkiewicz8648 Your inquiry is as follows: * Front TORQUE VALUES Handlebar lock nut 45 N·m (4.5 kgf·m, ) Steering stem lock nut 63 N·m (6.3 kgf·m,) Steering stem pinch bolt 27 N·m (2.7 kgf·m) Front axle 20 N·m (2.0 kgf·m,) Master cylinder reservoir cover screw 1.6N·m (0.16 kgf·m) Master cylinder holder bolt 12 N·m (1.2 kgf·m) Brake lever pivot bolt 2 N·m (0.2 kgf·m) Brake lever pivot nut 10 N·m (1 kgf·m,) Brake light switch screw 1 N·m (0.1 kgf·m,) Brake caliper mounting bolt 35 N·m (3.5 kgf·m,) ALOC bolt: replace with a new one. Brake caliper bleed screw 5.5N·m (0.55 kgf·m) Brake hose oil bolt 35 N·m (3.5 kgf·m) Install the pad pin by pushing the pads against the pad spring to align the pad pin holes in the pads and caliper. Install the front caliper onto the fork leg and then install and tighten the new two caliper mounting bolts to the specified torque. Torque: 35 N-m (3.5 kgf-m) Tighten the pad pins to the specified torque. Torque: 18 N-m (1.8 kgf-m, 13 lbf-ft) *Rear TORQUE VALUES Exhaust muffler lock bolt 35 N-m/3.5 kgf-m Exhaust muffler pipe nut 20 N-m/2 kgf-m Rear axle nut 120 N-m/12 kgf-m Rear shock absorber lower mount bolt 40N-m/4 kgf-m Rear shock absorber upper mount bolt 40N-m/4 kgf-m Rear brake caliper holder bolt 27 N-m/2.7 kgf-m

Don't you have to use torque settings?

@MotorcycleRepair

7 ай бұрын

There are no scenes using a torque wrench in the video above. However, it is recommended that those who do this type of work use a torque wrench for maintenance.

@starlord2660

7 ай бұрын

@@MotorcycleRepair Exactly, but aren't you supposed to use a torque wrench when tightening the clutch and variator? You used an impact wrench with no regard to torque settings, why?

@MotorcycleRepair

7 ай бұрын

@@starlord2660 First of all, every bolt, nut, and screw on a motorcycle has a specified torque value. In principle, it is correct to perform all work in accordance with the torque value. The work shown in the video... I'm not telling you how to maintain it. The purpose is simply to show the work process and to record it. It could be something like, “You can do it this way,” but... I'm not saying, "Do it like this." I don't know if the work of the mechanic in the video is possible because he has a lot of experience and work skills, but In general, this may not be a good method for unskilled people to follow. therefore ... I think you can just look at it for fun and think, "Ah, there are people who work that way..."

60 000km for a drive belt to last is crazy!

@MotorcycleRepair

9 ай бұрын

I also think it makes no sense. But... they say that this is the first replacement after 60,000km of driving...

@JohnSmith-pl2bk

Ай бұрын

The DAF55 and other Variomatics had 2 drive belts on their car transmissions and they lasted well back in the 1960's.. rubber technology and belt reinforcement fibres have had 55 years of development to get much better...

A cuantos kilómetros se cambia el aceite de transmisión trasero?

@MotorcycleRepair

3 ай бұрын

Generalmente se recomienda reemplazarlo entre 10.000 y 12.000 km.

@JesusAguilar-gw2oi

2 ай бұрын

Que cantidad(ml) de aceite de transmision lleva?

@MotorcycleRepair

2 ай бұрын

@@JesusAguilar-gw2oi La cantidad de reemplazo de aceite de transmisión es de 70 ml, y al desmontar y montar, agregue 90 ml.

@JesusAguilar-gw2oi

2 ай бұрын

80w 90w Motul o 10w 30w que aceite valdría?

@MotorcycleRepair

2 ай бұрын

@@JesusAguilar-gw2oi agregue aceite “10w 30”.

6만키로인데 벨트이빨하나도 안뭉개지고 금만조금 갓다구요? 버거가방달린거보니 배달용인데? 혼다기술이. 좋은건가 ㄷㄷ 무브볼은 거의깍두기가 다됏는데 쇠보다 고무벨트가 더튼튼하네 ㄷㄷ

@MotorcycleRepair

10 ай бұрын

그러게요..역대급입니다. 오토바이 주인분의 이야기로는 처음으로 교체를 하는것이라고 랍니다. 6만 키로를 운행것은 처음봅니다.

Me está dando fallo motor mi honda vision 110 2021 de que puede ser? Le cambie hace 2 días la bujia, aceite motor y la válvula de la caja de transmisión? Ayudame maestro

@MotorcycleRepair

2 ай бұрын

¿Has revisado también el filtro de aire?

@JesusAguilar-gw2oi

2 ай бұрын

@@MotorcycleRepair ya se quitó la luz por si sola, podria ser de el sensor de oxigeno (sonda Landa)? Es lo que se me ocurre

@MotorcycleRepair

2 ай бұрын

@@JesusAguilar-gw2oi El problema con el motor que no arranca es... Comprobar suministro eléctrico del generador. Problema con la bobina de encendido...mal contacto o cable defectuoso Problema con la bujía... Problema en el rectificador del regulador.. Problema con el filtro de aire.. Compruebe si la batería +/- está bien apretada. Conectado al chasis de la motocicleta - Asegúrese de que el negativo a tierra esté bien apretado. En la mayoría de los casos, puedes descubrir el problema comprobando esto. Desafortunadamente, esto no es algo que pueda comprobar directamente... No bastaría con hacértelo saber en este comentario. Utilice esto sólo como referencia.

인도네시아 혼다 부품 쓰시는군요

@MotorcycleRepair

10 ай бұрын

손님이 특별히 요구하지 않으면, 대부분의 부품은 부품 공급처에 주문을 하면, 공급처에서 주는 것을 그대로 사용합니다.😄

Новый ремень работает плохо. Это нормально? 😮

@MotorcycleRepair

10 ай бұрын

Да, говорят, что все в порядке.

우연히 영상하나 접햇는데 이거보니까 이것도 6만갈수도 있겠구나 싶네요 차종은 uhr이긴하지만요 kzread.info/dash/bejne/oWyllpiOiLfdcdo.htmlsi=Yc-Ve2sfKBA-wRBN

@MotorcycleRepair

10 ай бұрын

😊

나도 6만에 갈거임 ㅋㅋ

@MotorcycleRepair

9 ай бұрын

헉..아니됩니다. 3만정도 운행하였다면 점검받고 교체를 하세요

@doraiyo

5 ай бұрын

5만에 가세요

@Diego-mr2vk

18 күн бұрын

그냥 갈지 말고 평생 타세요

바이크주인할배 디질라고 작정을 했네 상태봐라 진짜 ㅋ

@MotorcycleRepair

11 күн бұрын

영상을 시청해 주셔서 감사합니다.

Lets red line a cold engine.

@MotorcycleRepair

8 ай бұрын

Thank you for watching the video. 😊

@dadirosharif123

7 ай бұрын

@@MotorcycleRepair do you have any videos of how to fix Honda vision 110 fuel pump please many thanks

@MotorcycleRepair

7 ай бұрын

@@dadirosharif123 I don't have any videos on how to repair a Honda Vision 110 fuel pump.

클러치슈 갈자 촌나 덜덜 거리네

@MotorcycleRepair

3 ай бұрын

시청해 주셔서 감사드립니다.