Honda Beat Timing Belt & Water Pump Replacement.
Фильм және анимация
Honda Beat Timing Belt & Water Pump Replacement How-To Installation Video. Also, Ron replaces the Valve Cover Gasket Set as well. Detailed video on removal and installation of the timing belt and water pump for a Honda Beat. Included in the video is how to set the timing up to ensure no engine damage after replacement. Hang around for the shenanigans Ron get's himself into during the install. As always, if you like what Ron is doing, SUBSCRIBE and let him know! Thanks for watching.
#jdm #kei #keicar #HondaBeat #Beat #MiniCar #Timingbelt #Howto #DIY #JDM #RHD #RHD_Ron #PP1 #Imported #Install #Installation #Guide
Пікірлер: 35
I would want everything you just did
This was an incredible video. I was dreading doing the belt on my Beat but this video made it seem a little less daunting. Still a hell of a lot of work, but doable!
@rhd_ron
Жыл бұрын
Thank you thank you. It is very tight. One of the rougher timing belt jobs I've done. I always read you had to pull the engine in the Beat to do it, but I thought that couldn't possibly be the case. I can tell you, it sure would have been easier with the engine out! LOL
Awesome video! It's hard to believe you did that job in 34 minutes 🤣!
@rhd_ron
Жыл бұрын
Thanks BT Transportation. Unbelievable how fast it is to do. LOL.
Getting ready for that drag race lol
@rhd_ron
Жыл бұрын
Doesn't matter if I win by an inch, or a mile, winning is winning..... HAHAHAHA
Alright, now you need to do an engine drop vid before you sell the Beat so we can see the difference! Trying to decide which route is best, esp since I don't have a lift! Great vid!
@rhd_ron
Жыл бұрын
I HEAR you! Beat has a deposit and pickup is scheduled next week. If I ever do a Beat again, I can tell you with certainty the engine is coming out. Lol. OMG. Tight quarters university
Great video straight to the point no gimmicks, i love it. I'm down to subscribe!
@rhd_ron
Жыл бұрын
Thank you for watching and subbing!
Nice walk through- thanks!
@rhd_ron
Жыл бұрын
Thanks for watching.
Lovely job, My mechanic just dropped the engine to get the belt done, but now I hear a loud whining noise that sounds like a supercharger whine. It might be the water pump is a bad unit or the oil pump failing so gona have him replace both, new waterpump is OEM this time and while at it. Replace all seals and gaskets, document the crankshaft and bearings, replace piston rings, replace motor mounts, replace gas tank, replace entire clutch assembly. Very very expensive service hours probably 2500- 3000$ worth but all preventative maintenance and age related issues I had planned being taken care of will make me very very happy :P
@rhd_ron
Жыл бұрын
Yes as I got into it, I thought about dropping the engine/transmission out. But, so many people were asking if it could be done without doing so, so I wanted to show that it can, although a little more difficult. I can imagine that level of work you are having done is worth every penny!
@darkmugetsu6572
Жыл бұрын
@@rhd_ron spending as many thousands and thousands on a vehicle I won't get back is not worth it. But I know no other car exists out there that gives this kind of amazing driving experiences so I go way above and beyond to make sure nothing goes wrong, wether it be replacing the entire distributor since there had been cases of them randomly seizing up. To replacing the gas tank cause its 31 years old who knows how much rust is built up in there.
Ayyy I’m sure I’ll be doing the job soon 🤘🏼
@rhd_ron
Жыл бұрын
Hang in there! It IS possible but man is it tight quarters University....haha good luck
This video was a great help! However, that annoying background music on your video was playing in my head during the whole procedure. MAKE IT STOP!!! A few things to add: Buy the very best LONG 14mm 6-point wrench you can find. Only use 6-point sockets on the engine mount bolts and nuts. Have one of those magnet retriever things handy for when that metal spacer retracts into the plastic engine cover while you are trying to reinstall the engine mount (no big deal just annoying). If your Beat has "valve clatter" THIS is the time to do the valve adjustment. Don't expect the camshaft and crankshaft timing marks to line up EXACTLY all by themselves. There's a little fudge factor involved. If one set of marks lines up and you can manually move the other pulley onto its timing marks WITHOUT moving the other pulley off its marks you are good to go. You couldn't do that if you were one tooth off. The Beat service manual lists the torque spec for the crank pulley bolt as 11.5 Kg-m or 83 lb-ft.
@rhd_ron
Жыл бұрын
Thanks for the view, sorry about the music, I dont like dead silence videos. Yeah there is a lot of detail I could Go into, like how Honda made a hole in the frame of the Beat side chassis to accommodate the engine mount bolts Being removed for this job. Tried to keep it to what was required around general mechanic items. Thanks!
@RHD_Ron great video thanks. You sound like you might be in the south....are you for hire to perform this service? I'm in GA and am looking for someone who can do a timing belt service for a Honda Beat.
Did anyone else see an old stripped timing belt tooth at the crank pulley @ 18.24 at the top of the picture and @ 21.50 to the right hand side of the new belt? A little worrying. Where did it come from? Did the car have timing belt failure in the past? Also, did it get removed before building it back up?????
@rhd_ron
Жыл бұрын
Hmmm, can't say that I see what you are talking about at those two specific times. This little truck was super low mileage and I did the belt just because you never know the history when you get these from Japan. The work was done and the truck has been on the road over a year now. Thanks for the watch.
Great video! How long did this job take?
@rhd_ron
4 ай бұрын
About double what it should have with filming. LOL. I cant remember, maybe 8hrs with no filming? Its tight!
Hey, does your beat make a whining sound when the engine is hot at operating temperature? Some say that it is normal or might be. I managed to locate it maybe around the lower timing belt cover area. Maybe going to try to adjust the belt tension
Will that kit work for the 96 honda today rs ... same motor as beat 656cc E07A MTREC... JA4 body ... don't need it yet but may as well order one for the future.. I do need to find a rear motor mount.. I can't find one ...
@rhd_ron
4 ай бұрын
Not sure if the transmission parts interchange. I would this so being a E07 transmission but cannot confirm.
Excellent video! Could you please give us the mm size of the hex crank pulley tool?
@rhd_ron
Жыл бұрын
50mm crank pulley tool. Thanks
Lol classic!!!!!
👌 ᴘʀᴏᴍᴏsᴍ
With a Z!!!!
DAM not much room in there
@rhd_ron
Жыл бұрын
Man it's a squeeeeeze on these KEIs. The Beat did not disappoint. 😀