In this video we start building our homemade lake pontoon boat Music: Santa Cruz - Aiming High #pontoon #homemade #diy
Жүктеу.....
Пікірлер: 28
@7ann33 жыл бұрын
A tip. I have found that with high load the barrels get a bit crushed. Buy tire valves for car rims. Drill a hole in one of the barrel caps fitting the valve. Mount the valve in the cap hole. Get it a little bit of over pressure. Not much, just so it get a bit harder and dont collapse. Works great for us and it also helps when there are big temp, differense lika we have.
@pramodmallik
2 жыл бұрын
Good suggession sir . I also feel so. Filling Air inside the pontoons @10 to 14 PSI would be fine for protection from bulging and bending the pontoons .More over pontoon buoyancy capacity will too increase .
@MP-uc6zb
2 жыл бұрын
Where do you install valves? In the cap or right in the barrel? Maybe on the side for easier access?
@7ann3
2 жыл бұрын
@@MP-uc6zb i did it in the cap. It have rhicker mtrl. Still works great. We have winter now with many sub zero c degrees and they are still firmly round.
@scootersonlyrepair6773
2 жыл бұрын
Also shoving a deflated truck inner tube in the barrel and then inflating it will help win case anything causes a leak in the barrel
@bird1671
Жыл бұрын
Damn good idea bro
@jesseaviman3 жыл бұрын
This is gunna be an awesome build!
@rafaelneiva68910 ай бұрын
Hi... here from Brasil. I haven' found The vídeo number 4, 5 and 6.
@johnrayson6212 Жыл бұрын
easy way to pressurise barrels uncrushable is to add a spoon of dry ice then close tight but not too much as could expload
@rasman1215 Жыл бұрын
Mantep bang🎉🎉😊
@agustiawanbire87982 жыл бұрын
The best
@roberttiffany58962 жыл бұрын
I can dig it. Also that song was awesome 💪😎
@ShoreGarage
2 жыл бұрын
Thank you! It’s a ton of fun and my family loves it!
@murahrezeki2726 Жыл бұрын
What frame size
@stellamitchell-bathgate58233 жыл бұрын
how much did it cost all round
@ShoreGarage
3 жыл бұрын
Roughly around $700 US
@dellpacker7657
2 жыл бұрын
@@ShoreGarage what was the most expensive part of the boat to make / buy ?
@ShoreGarage
2 жыл бұрын
@@dellpacker7657 the motors and the batteries. The actual wood nowadays is pretty cheap to acquire
@edr9276 Жыл бұрын
How do you title a home built boat?
@ShoreGarage
Жыл бұрын
Love it!
@dougearnest7590
Жыл бұрын
It probably varies by state. In Texas boat titles and registration are handled by the Texas Parks and Wildlife Department. In some other states it might be the same entity that handles vehicle registration. IIRC, for Texas, in addition to a form you have to fill out, you also need to show receits for the materials purchased, and a Game Warden has to come look at it the boat. I suspect you can find the requirements in your state easily by searching online.
@aggabus Жыл бұрын
Devil worship noise
@jesseaviman
Жыл бұрын
It’s nowhere near that, most likely better then what you listen too!
@aggabus
Жыл бұрын
@@jesseaviman what is better
@ShoreGarage
Жыл бұрын
Thanks for the comment! But as far as this music, it’s far from devil warship noise.
Пікірлер: 28
A tip. I have found that with high load the barrels get a bit crushed. Buy tire valves for car rims. Drill a hole in one of the barrel caps fitting the valve. Mount the valve in the cap hole. Get it a little bit of over pressure. Not much, just so it get a bit harder and dont collapse. Works great for us and it also helps when there are big temp, differense lika we have.
@pramodmallik
2 жыл бұрын
Good suggession sir . I also feel so. Filling Air inside the pontoons @10 to 14 PSI would be fine for protection from bulging and bending the pontoons .More over pontoon buoyancy capacity will too increase .
@MP-uc6zb
2 жыл бұрын
Where do you install valves? In the cap or right in the barrel? Maybe on the side for easier access?
@7ann3
2 жыл бұрын
@@MP-uc6zb i did it in the cap. It have rhicker mtrl. Still works great. We have winter now with many sub zero c degrees and they are still firmly round.
@scootersonlyrepair6773
2 жыл бұрын
Also shoving a deflated truck inner tube in the barrel and then inflating it will help win case anything causes a leak in the barrel
@bird1671
Жыл бұрын
Damn good idea bro
This is gunna be an awesome build!
Hi... here from Brasil. I haven' found The vídeo number 4, 5 and 6.
easy way to pressurise barrels uncrushable is to add a spoon of dry ice then close tight but not too much as could expload
Mantep bang🎉🎉😊
The best
I can dig it. Also that song was awesome 💪😎
@ShoreGarage
2 жыл бұрын
Thank you! It’s a ton of fun and my family loves it!
What frame size
how much did it cost all round
@ShoreGarage
3 жыл бұрын
Roughly around $700 US
@dellpacker7657
2 жыл бұрын
@@ShoreGarage what was the most expensive part of the boat to make / buy ?
@ShoreGarage
2 жыл бұрын
@@dellpacker7657 the motors and the batteries. The actual wood nowadays is pretty cheap to acquire
How do you title a home built boat?
@ShoreGarage
Жыл бұрын
Love it!
@dougearnest7590
Жыл бұрын
It probably varies by state. In Texas boat titles and registration are handled by the Texas Parks and Wildlife Department. In some other states it might be the same entity that handles vehicle registration. IIRC, for Texas, in addition to a form you have to fill out, you also need to show receits for the materials purchased, and a Game Warden has to come look at it the boat. I suspect you can find the requirements in your state easily by searching online.
Devil worship noise
@jesseaviman
Жыл бұрын
It’s nowhere near that, most likely better then what you listen too!
@aggabus
Жыл бұрын
@@jesseaviman what is better
@ShoreGarage
Жыл бұрын
Thanks for the comment! But as far as this music, it’s far from devil warship noise.