Thanks for that video. Just waiting for my frame and had some left over questions regarding crossfire and beta flight, which you answered!

Yep I was o

Nice build 🧐

Hei can you add something on OSD with this FC?

Just wired up my crossfire nano to kakute f7 hdv (successfully) and was struggling to get it to work... like ALL day today. Just now finally got it to work. For this fc you need to wire tx of receiver to tx of the fc. and rx of receiver to rx of fc. Dangit. Dangit. And dangit.

@mrRockwellFPV

3 жыл бұрын

Hmmm. Interesting

Thanks for making the video. As you’re using crossfire receiver by soldering on to the flight controller, do you still use all the connections with the air unit do you need to cut some wires in that plug to not use the tx and rx of the air unit or is that something you can config in beta flight?

@mrRockwellFPV

4 жыл бұрын

No. You can used supplied cable with crossfire rx as long as you select serial port on the corresponding uart port.

@peterfoleyusa

4 жыл бұрын

@@mrRockwellFPV But then are the Air unit and crossfire both sending out RC signals? Is there a way to disable the air unit from RC signals?

Do you have issues using 5 or 6S? My quad is falling out of the sky with everything above 4S.Do I need to connect the esc + and - to B+ and B - for 6S? And if so, disconnect + and - from the plug?

@mrRockwellFPV

4 жыл бұрын

Just solder everything up like I did and you will be good

help me understand. Your kakute came with a wire that will connect directly to the DJI air unit? Mine did not come with a wire that does that, and my DJI air unit only came with a male connector on one side, and exposed wires without connector on the other side. Do you have any idea where I can find that wire???

@mrRockwellFPV

4 жыл бұрын

Hmmm. That's a tough one. Really don't know. But standard dji cable canbe made to fit the jst connector on the fc

Thank you for sharing, why not use the DJI air unit for video and flight control of the drone? Is it because you have the DJI goggles but not the DJI controller?

@mrRockwellFPV

4 жыл бұрын

Yup. Personally I prefer crossfire for my rc control over any other

will this set up work with the taranis x9d and the dji goggles ? does using the cross fire mean that you don't need the antenna for your radio controller anymore ?

@mrRockwellFPV

4 жыл бұрын

It will work with any other system that your use. Instead of crsf rx you solder on whatever rx you have.

what the wiring between BEC and Kakute F7 with non dji flight controller.

@mrRockwellFPV

4 жыл бұрын

It's like any other fc. It's all uart ports you solder your pheriprials to

hello, nice video.. can you help me please my kakute f7 is uneable give enough voltage to start my dji unit.. im using the cable for dji unit from kakute.. when i connect dji unit to battery direct then it work but from kakute not..voltage from kakute is too low.

@mrRockwellFPV

3 жыл бұрын

Maybe you have a faulty 9v reg. I'm sure that the shop you bought it from will warranty it.

Can you use that flight controller in a 6S built? Or u need a voltage regulator?

@jaysway007

4 жыл бұрын

6S ready.... I have this on two 6S builds....no issues, and it comes with a capacitor

@SbremboMkultra

4 жыл бұрын

@@jaysway007 tnks man. tnks for the reply. I'll be able to build a 6S then. Tnks a lot.

@anweshdevkota7044

4 жыл бұрын

@@jaysway007 So 6s build doesn't require extra BEC on kakute F7 that has capacitor right