Hedge trimmer sharpening. Hedge cutter sharpening and service. how i sharpen my hedge, shrub trimmer attachments
Жүктеу.....
Пікірлер: 161
@brittweir8844 Жыл бұрын
Hands down the best hedge trimmer video on here . I like how you take the time to clean the parts first. sharpen with the file. Then reassemble clean Parts using a good Grease, I personally use manufacturer's recommended oils and Grease. I find the German products to be the best. But I also respect your points how you say this is how you do it. Thumbs up my friend good job. In my opinion.
@defan210521 күн бұрын
I have a cheap electric one but this video was so good, I had to watch all of it! Well done.
@billyk50387 ай бұрын
Thanks Jason. Used my Bosch Hedgepole 18 on leylandii a few days ago. Has "anti-block system" to cut thicker branches. has been jamming since even on very thin ends. Decided to strip down for blade sharpening and flattening out any unseen burrs with a flat file and a chain saw file. School boy error. Cant re-assemble it- left with extra spacer. After watching this excellent video i'm starting again. I'm going in.Wish me luck.😁😁😁
@streakyfish Жыл бұрын
Just the video I was looking for. Despite using an angle grinder for work everyday I didn’t fancy using one in this instance. Very well documented 👍
@sunnysidegardeners71634 жыл бұрын
One of the best ways to sharpen your blades in my opinion. Can’t beat a good hand file and elbow grease to keep a nice flat 45 angle on the cutting tooth. 👍👍
@jasongardener3425
4 жыл бұрын
👍👍
@teaganwindago31322 жыл бұрын
Your video is why I watch several videos on the subject. You have the first video I found disassembling the blades and using a file. If I need dis-assembly I'll find out soon enough. Old school men prefer a file against a dremel or die grinder. This I know from knowing people that have used both methods. I wasn't taught much growing up so event at 48.75 years of age I still seek advice. The dumbest question is the one not asked! And yes you can quote me on that!
@themowerman4 жыл бұрын
Yeah it’s fair to say I enjoyed that. Watched in full. With a nice mug of coffee
@neilgallacher47933 жыл бұрын
I like the way that your thorough approach to doing the job itself is reflected in the way you made the video. Really appreciated watching this. Thanks!
@jasongardener3425
3 жыл бұрын
Thanks mate, I appreciate that, glad you enjoyed it 😊👍
@rollotomassi62322 жыл бұрын
Best advise from this video; "Don't be in a rush, just take your time." This can be applied to almost everything in life.
@stephenwolstenholme44514 жыл бұрын
Hi Jason, i find putting the drive rod on top of the main gear and then lowering the gearbox to line it up is a lot easier. The grease won't fall out and then flip it back over to continue the rebuild. A great video and really enjoy your your approach to gardening. I have been in the trade for 36 years and still love it rain or shine despite the aches and pains.
@jayellis2939
Жыл бұрын
Great tutorial video. Thanks!
@thegeordiefellwalker88784 жыл бұрын
very thorough Jason. great results with the two files, will drop my two stihl cutters in over the weekend cheers.
@DunningsMillLawnCare4 жыл бұрын
Hi Jason, this was very helpful! In 4 years time I'll be 18 and starting my own gardening and tree surgery business, there for I now see how I could sharpen my hedge cutter blades in the future.
@Rafabenitez01
8 ай бұрын
Good luck 👍
@keneagle76844 жыл бұрын
Well done. Just enough explanation without to much talking and a nice soft easy to listen to background music.
@rlfdfd50593 жыл бұрын
Big love from up norf! Such a calming voice ... and I'm gonna try and sharpen the teeth on my 36v Ryobi
@jasongardener3425
3 жыл бұрын
👌👍👍
@andregreen80402 жыл бұрын
Wonderful job. I loved the way that you removed all the old grease, washed the parts before reinstalling them and filed the blades by hand. I’ve seen videos on KZread where they replace the old blades with new ones but they leave the old dirty grease and dirt build up in the gear housing. Unbelievable that they’re making instructional videos, and what’s worse is that people compliment him on a great job. You gotta shake your head in disbelief.
@jasongardener3425
2 жыл бұрын
Thanks Andre, iv seen many videos and I have to agree with you 👍
@ocrun6765 Жыл бұрын
Very nice. The Samurai would be proud of you.
@jasongardener3425
Жыл бұрын
Thanks mate 🙂
@axal3214 жыл бұрын
very well done Jason love your videos Bud
@jeraldsmith25454 жыл бұрын
Enjoyed the video! Nice tip with the chainsaw blade. I will definitely be using that method next time I sharpen my trimmers.
@jamiewhite27224 жыл бұрын
I see a lot of comments saying use a grinder it takes less time, but like when sharpening chainsaw chains it needs to be done properly to make them laser sharp! Once you get the hang of it, it takes no time at all. Grand job. Tip for future. Use a diluted bleach cleaner after a cutting session . Stops possible infection passing from hedge to hedge
@simoncordingley31224 жыл бұрын
That intro music puts the fear into you. I haven't felt that since Jaws! :D
@sulemanyusufadam43153 жыл бұрын
Best video I’ve found on this! How often do you grease the gearbox via the screw hole, and what grease do you use? Thanks
@bobkeeler59643 жыл бұрын
I've done this and it’s a pain in the arse. I always have loose parts when doing this. This is why I prefer using a Dremmel tool or a grinder at slow speed to just sharpen the blades without getting into the gear box
@berniemoscrop53323 жыл бұрын
Great job Jason, it's a time consuming job sharpening hedge cutter blades as i do my own too.
@jasongardener3425
3 жыл бұрын
Yes definitely, but a file is for me the best way, I do on sometimes use a sanding pad, when really busy and time is a issue for me, but file is perfect 👍
@carabela1252 жыл бұрын
Thanks for posting the video. It was a help getting mine back together again. I used motorcycle chain lube between the blades, going to see how well that works.
@jasongardener3425
2 жыл бұрын
Cool 😊👍
@mikenicholas8853 жыл бұрын
Really enjoyed the video and your teaching style. I file old school crosscut saws and like to modify my flat files with an angle grinder to round off the sharp corners and not put a nick in the saw plate. With a safe file you can rub the curved part as a guide to make filing fast and accurate. Saw filers use felt markers on teeth to insure proper angle when filing. Ink is cheap. Quick question, I used chainsaw bar oil as a lubricant since it's anti-fling but don't know if it can harm plants.
@neusac45904 жыл бұрын
Nice video Jason. Good to know how to do that. 👍👍👍👍👍🇺🇸
@stillwill18085 ай бұрын
Beautiful! I wish I could make a blade look that good. I have a hard time maintaining the factory angle. Same problem I have with scissors. You make it look so easy.
@jasongardener3425
5 ай бұрын
Thank you, the trick is to not rush. 👍👍
@roystheboy4 жыл бұрын
Nice video jason i did a sthil km94rc cutter today i use a grinder with a well used flappy disc that is rounded of at the edges that does the round bits easy on a slow speed and i had to replace 2 connecting rods where one had the bearings come out
@kevinpercival280z2 ай бұрын
Great video loved it! I'm looking forward to doing this!
@jasongardener3425
2 ай бұрын
🙂👍
@arturocruz1993 Жыл бұрын
Very satisfying sharpening blades with a file.
@jasongardener3425
Жыл бұрын
Thanks 👍😀
@bernardinobautista4992 жыл бұрын
This the best video I have seen thank you so much
@jasongardener3425
2 жыл бұрын
😀👍👍
@westrupsgardening76874 жыл бұрын
Exceedingly good craftsmanship.
@boyse693 жыл бұрын
Great time of the year clean and sharpen and put away ready to go ! Well worth the effort if you know the cost of these hedge trimmers blades £75 for a good set. But Also good to have spares sharp on the shelf .
@jasonhewlett12832 жыл бұрын
I must have missed this one somehow 🤔 . Very informative 👏 👌.
@cristallewis78022 жыл бұрын
Love the video, I use a strop after every use you can buy round strops for mowers there about the same size as a chainsaw file. I also clean the tool to prevent any cross contamination of diseases between plants. Super important with chain saws and pruning saws.
@jasongardener3425
2 жыл бұрын
😀👍
@alangardiner72502 жыл бұрын
Nice one Jason. Many thanks.
@HoopersGardenMaintenance4 жыл бұрын
Great video Jason,very Informative 👌🏼
@josephmccole41324 жыл бұрын
Fantastic. I fancy giving that a go!
@corvysone22 жыл бұрын
A very good tutorial and thorough in every respect I enjoyed this immensely.
@jasongardener3425
2 жыл бұрын
Thank you very much 😀👍
@bumpkinrocks4 жыл бұрын
Good video Jason👍 I cheat on mine and use a grinder, used to hand fill but took to long. The blades look identical to Stihls and internals much the same. I see the needle bearings in the con rod are different. Do they last longer? I've got 8 Stihl sets sharpened just got to sand and reassemble. Then I just swap blades through the season, can't use dull blades!😪 👍
@milllworks Жыл бұрын
Followed this verbatim. Worked perfectly. Many thanks.
@jasongardener3425
Жыл бұрын
😀👍
@JoerivanLith4 жыл бұрын
They look very sharp. I do the same with disassembling/assembling the blades. But I sand both sides of the blades with a sander. Then I place the blades on a working bench and use an air grinder to sharpen the teeth. I use the dirt on the teeth as marker for the correct angle.
@bumpkinrocks
4 жыл бұрын
I do exactly the same👍
@smartcatcollarproject5699
3 жыл бұрын
Just curious, I don't even own a compressor, but can you invert the rotation on an air grinder ?
@BhekiBear4 жыл бұрын
Great video! Do you have to take the blades apart to sharpen or can you do them while attached to the head?
@MOWTOWN4 жыл бұрын
Thanks for putting this up mate, big help. Cheers
@jeffwilson14843 жыл бұрын
That was a great job I liked watching that.
@jasongardener3425
3 жыл бұрын
Cheers mate 😀👍
@phaedrabacker20044 жыл бұрын
Excellent presentation. Now I know what to do. Cheers to you.
@cesarblanco14 күн бұрын
Great video. Thanks from Spain.
@jasongardener3425
14 күн бұрын
@@cesarblanco thank you 😊
@TheWuudCam3 жыл бұрын
Nice one... found that very helpful. Thanks to YOU
@marcobortoli15144 жыл бұрын
Hi, thank you so much for your tutorial. I have a question: the flat file is a second cut or smooth cut? Thanks.
@aurelioayala32993 жыл бұрын
Thanks men that was the best video I ever see 👍👍
@jasongardener3425
3 жыл бұрын
Thanks mate 👍👍
@zerocool2121213 жыл бұрын
Try a die grinder, they can get the insides and get everything in very little time. Its even faster and leaves better results than a dremel. Ill bet i can sharpen a 24" in 5-10 mins tops, then switch pads to a non abrasive to polish the top if needed/desired. I will say you did a very clean and nice job, just to long for myself.
@pb99264 жыл бұрын
Thorough job indeed 👍
@Yaridnac4 жыл бұрын
Beautifully done sir, yes sharpening and cleaning things is relaxing. ^_^
@chrisbath39614 жыл бұрын
Thanks for that Jason, I think that's my Sunday afternoon taken care of! I seem to remember you mention that you make adapt/shorten your shafts for the long reach? I've been trying to suss out how to do it on a kombi, any chance of some pointers before I cock mine up? 😂 Hope your doing OK in the current situation and all the best👍
@Pro1er4 жыл бұрын
Seriously nice job!
@aussieallrounder60184 жыл бұрын
Thanks for this. Appreciate it.
@TheCountryCottageGardener4 жыл бұрын
Nice educational video pal..am guilty of using a electric grinder, purely down to time like you say. Hope your keeping busy 👍
@MattGlynn3 жыл бұрын
well in depth- great video.
@jasongardener3425
3 жыл бұрын
👍
@johnbates79713 жыл бұрын
Great job - will give it a go knowing this is very thorough. Apart from elbow grease - what sort of grease do you use in the tub - I usually grease with Stihl on the grease point but interested to know alternatives
@jayellis2939
Жыл бұрын
Same question l had.I Bought a tube of stihl but misplaced it.
@welshmaniacs163 жыл бұрын
quick questions lol but do you empty all your machines of fuel for storage in winter or is the fuel good to go all year around? need to service my hedge cutter, do you recommend a half round file for the corner bits? what brand files do you recommend? great video btw, very chilled and informative 👍🏻
@1234loci4 жыл бұрын
I’m using a dremel (micro-grinder) the results are good but not this good I guess. However it takes way less time to do it. Great video btw I would love to see more tool-maintenance video from you maybe how you properly sharpen and maintain your pruning tools?
@smartcatcollarproject5699
3 жыл бұрын
I suppose the main difference is that your blades may last longer this way, as you can work with more precision than a dremel or a grinder ? That said mine has 21 teeth, that's 160+ faces to file, and I'm not sure I'll finish that work by hand ! Maybe I need a larger file, like in the video...
@carlwaylett70134 жыл бұрын
Hi Jason great video very interesting 👍i never took one to bits as yet 👍are you busye now the season is up and running 👍
@lincsfencingandgardeningse91284 жыл бұрын
Beautifully done. Very nice video too. M
@paulbolger57614 жыл бұрын
Great video jason that is a great idea with chainsaw file
@gareth49094 жыл бұрын
That was useful thanks 👍🏽
@Premier_lawns_official4 жыл бұрын
Great video, well explained. Very sharp, excuse the pun. As good as new.
@psp7773 жыл бұрын
my blades gum up too easily. I use the Stihl cleaner, but I thin it actually makes it worse. What are people using to keep their blades clean and lubricated after each use?
@morokeiboethia6749 Жыл бұрын
Question - if you are sharpening a machete with a flat file like you have on the video, do you push the file perpendicular to the blade (with the back end of file raised to match the bevel angle of the blade)? Or are you supposed to turn the file until the cutting lines on the file are parallel with the machete's blade edge, and then push forward? Was wondering why the lines are running at an angle on the file. I just bought a flat file 2 pack and have no idea how to correctly use it to sharpen.
@frundlemud Жыл бұрын
solid job.
@PJ-tt2nz4 жыл бұрын
What do you use to lubricate the blades and how often do you do it?
@TheFullyChargedGardener4 жыл бұрын
😀 A great video chap - So important to keep those blades sharp. Bootiful work 👏🏻
@RedFace13 жыл бұрын
Excellent video. Only wish the customers had their gasket replaced with that moisture
@Speedy120Dave3 жыл бұрын
“Wear gloves... one slip and it’s gonna hurt” oh yesss indeed. I did mine last year for the first time, total pain in the rear, may give it another go as they’re all manky between the blades. Blades nearest machine are still pretty decent but blades nearer the tip, not so great.
@playlistawyoutubie1691 Жыл бұрын
Thanks a lot!!!
@dale-icious89023 жыл бұрын
Really helpful. Thank you.
@jasongardener3425
3 жыл бұрын
👍
@sionyevans3 жыл бұрын
Good work my man
@treebutcher20004 жыл бұрын
Great job there 👍, some of the con rod bearings in the stihl gearboxes can be a bit of a nightmare if you're not used to doing them but you have done a good job of those for sure.
@sergeivershinin5492 жыл бұрын
How often do you perform such servicing on the practice? Thank you.
@carlodonnell14611 ай бұрын
the good thing about taking it apart to sharpen the blades is that you can apply fresh grease at the same time I suppose; but getting back together correctly is imperative if it is going to work.
@teaganwindago31322 жыл бұрын
@ 8:35 I would of never thought of decking the blades. As you flatten them out from knicks the process is called decking. Like what engine cylinder heads and blocks are normally done to during a rebuild. Now I see the need for disassembly. I'll continue the video so you wont have 10 comments to read. You already have 2 from me. Now it's your turn to learn. WD-40 and similar solvents will be bounced off your head if pulled out in an American machine shop. By best friend is a machinist that makes the tooling that makes artificial limbs and organs. Solvents like WD-40 collect a massive amount of dirt, grit, and every thing you don't want in a cutting tool. Yeah I know that is a hard pill to swallow but it's true. Do I still use it. YES!!! But I hide everything like it when I know he is coming for a visit. Garden tools that I have sprayed off with a water hose will always get a healthy dose of WD-40 or similar rust prevention lubricant. now lets see what else is in the video. I'm writing as I come across parts of your video. So I don't know what's next. I'm truly being honest. And that is almost impossible to find now days. RE- Assembly? I would never use 3&1 oil. I prefer using the thickest Royal Purple engine oil. I even use it while doing machine work. @ 12:36 I use waterproof High temp grease for the gearbox and Bar and Chain saw oil for the blades before and after I use the tool. OH Hell man I just did that. I tightened everything up and the blades wouldn't move. I will try to find the proper torque setting for my tool. I hope you read all this. I took a 13:48 video and made it 4 times longer. I learned a lot. I hope you will as well.
@AJPsWorkshop4 жыл бұрын
Great video
@apaul13150 Жыл бұрын
Well I think I can safely say that the job could physically not be done better than that, and Jason is a FKN perfectionist maniac.
@jasongardener3425
Жыл бұрын
Cheers mate 👍
@SuperRonan833 жыл бұрын
Wonderfully entertaining
@leebennett36722 жыл бұрын
Great job 🙂
@jasongardener3425
2 жыл бұрын
😀👍
@ronaldvanderhall4533 Жыл бұрын
Very nice instructions
@jasongardener3425
Жыл бұрын
Thank you 👍
@user-gi3xj8nz3s3 жыл бұрын
Do you have a link on both the files you used ? Can I get them at Amazon?. Great video by the way keep it up 👍
@robrusticwoodlandproducts66624 жыл бұрын
Nice work 👍
@brayvdb21912 жыл бұрын
You don't really have to time the whole blade just see how long you take over X amount of teeth divide that time by the amount of teeth you did and then multiply by how many teeth there are. I always thought u need a grinder because my old workplace did it that way but I'm happy to see I can use a simple file. I always enjoyed using a classic hand tool
@ASQUITHZ9 Жыл бұрын
Hi Jason, Thanks for your film! but I can't understand why any one would sharpen any tool towards the leading edge I have been sharpening tools for over 65years starting life in a joiners shop and other trades requiring sharp tools and other implements as well as my own tools. When you have sharpened your blades and turned them over and scoured them for want of a better word all you are doing is transferring the burr that you created in the first place by honing towards and under the leading edge. I suppose that's good enough for (rough arse gardening tackle) as most people would call it! not a precision cabinet maker and or musical instrument makers tools (look at Ray Mears films and tackle for sharpening his bush Knifes and axes!) for my gardening cutters I use a Diamond file sharpening from underneath the blade away from the leading edge and a half round file for the curves and to remove the burr a hardwood block with some lube rubbed over the cutting edge on the end grain job done. As for cleaning I submerge my cutters in a soil pipe filled with diesel run for a bit and dried off and at laying of time some sack cloth with a bit of light oil Job done and I've had the same cutters 25 years no probs!!! But if it works for you good, and anyone else who doesn't know how to sharpen up properly fair enough, but I cringe when I see it! It reminds me when as joiners, we used to get 15 mins sharpening up time before everyone else finished work If we had have been seen sharpening up like that we would have got peddled (on your bike kid) But thanks again.
@daveh1081
Жыл бұрын
Jonathan......that's an interesting take on sharpening. I always took an interest in metalwork at school and I still love to learn stuff like that. So always sharpen AWAY from the leading edge, right? I get the logic yet it still feels "wrong" somehow but I'm going to try it. Wow......every day really is a school day! 👍👍
@jimmydickson8854 Жыл бұрын
Thanks Jason jimmy Aust
@jasongardener3425
Жыл бұрын
👍👍
@danielholmes58234 жыл бұрын
Nice job
@hobbs34243 жыл бұрын
very meticulous....i do like.
@jasongardener3425
3 жыл бұрын
👍
@tonycritcher34194 жыл бұрын
nice one!
@jackw99204 жыл бұрын
Wish I had the patience to do that. I just pay to get them sharpened.
@simonparry38234 жыл бұрын
Brilliant job how often you sharpen the blade's ?
@jasongardener3425
4 жыл бұрын
Thanks mate, a total strip down is once or twice a year, but I give a light run over with a file, probably even 4 or 5 weeks in general 👍
@simonparry3823
4 жыл бұрын
@@jasongardener3425 thanks on that need to file a bit more in the cutting season 👊
@bobbelsekwol4 жыл бұрын
Yeah, wear gloves. Sliced hands with a dirty blade are a ready disaster. Great vid covering all the aspects of the blades. Cheers.
@nivid01 Жыл бұрын
You should be using a small half round file mate!!!!
@alansteele3757 Жыл бұрын
Quality 👍👍
@terrypalmer11793 жыл бұрын
ya i really did not know untail now , so thanks. t.
Пікірлер: 161
Hands down the best hedge trimmer video on here . I like how you take the time to clean the parts first. sharpen with the file. Then reassemble clean Parts using a good Grease, I personally use manufacturer's recommended oils and Grease. I find the German products to be the best. But I also respect your points how you say this is how you do it. Thumbs up my friend good job. In my opinion.
I have a cheap electric one but this video was so good, I had to watch all of it! Well done.
Thanks Jason. Used my Bosch Hedgepole 18 on leylandii a few days ago. Has "anti-block system" to cut thicker branches. has been jamming since even on very thin ends. Decided to strip down for blade sharpening and flattening out any unseen burrs with a flat file and a chain saw file. School boy error. Cant re-assemble it- left with extra spacer. After watching this excellent video i'm starting again. I'm going in.Wish me luck.😁😁😁
Just the video I was looking for. Despite using an angle grinder for work everyday I didn’t fancy using one in this instance. Very well documented 👍
One of the best ways to sharpen your blades in my opinion. Can’t beat a good hand file and elbow grease to keep a nice flat 45 angle on the cutting tooth. 👍👍
@jasongardener3425
4 жыл бұрын
👍👍
Your video is why I watch several videos on the subject. You have the first video I found disassembling the blades and using a file. If I need dis-assembly I'll find out soon enough. Old school men prefer a file against a dremel or die grinder. This I know from knowing people that have used both methods. I wasn't taught much growing up so event at 48.75 years of age I still seek advice. The dumbest question is the one not asked! And yes you can quote me on that!
Yeah it’s fair to say I enjoyed that. Watched in full. With a nice mug of coffee
I like the way that your thorough approach to doing the job itself is reflected in the way you made the video. Really appreciated watching this. Thanks!
@jasongardener3425
3 жыл бұрын
Thanks mate, I appreciate that, glad you enjoyed it 😊👍
Best advise from this video; "Don't be in a rush, just take your time." This can be applied to almost everything in life.
Hi Jason, i find putting the drive rod on top of the main gear and then lowering the gearbox to line it up is a lot easier. The grease won't fall out and then flip it back over to continue the rebuild. A great video and really enjoy your your approach to gardening. I have been in the trade for 36 years and still love it rain or shine despite the aches and pains.
@jayellis2939
Жыл бұрын
Great tutorial video. Thanks!
very thorough Jason. great results with the two files, will drop my two stihl cutters in over the weekend cheers.
Hi Jason, this was very helpful! In 4 years time I'll be 18 and starting my own gardening and tree surgery business, there for I now see how I could sharpen my hedge cutter blades in the future.
@Rafabenitez01
8 ай бұрын
Good luck 👍
Well done. Just enough explanation without to much talking and a nice soft easy to listen to background music.
Big love from up norf! Such a calming voice ... and I'm gonna try and sharpen the teeth on my 36v Ryobi
@jasongardener3425
3 жыл бұрын
👌👍👍
Wonderful job. I loved the way that you removed all the old grease, washed the parts before reinstalling them and filed the blades by hand. I’ve seen videos on KZread where they replace the old blades with new ones but they leave the old dirty grease and dirt build up in the gear housing. Unbelievable that they’re making instructional videos, and what’s worse is that people compliment him on a great job. You gotta shake your head in disbelief.
@jasongardener3425
2 жыл бұрын
Thanks Andre, iv seen many videos and I have to agree with you 👍
Very nice. The Samurai would be proud of you.
@jasongardener3425
Жыл бұрын
Thanks mate 🙂
very well done Jason love your videos Bud
Enjoyed the video! Nice tip with the chainsaw blade. I will definitely be using that method next time I sharpen my trimmers.
I see a lot of comments saying use a grinder it takes less time, but like when sharpening chainsaw chains it needs to be done properly to make them laser sharp! Once you get the hang of it, it takes no time at all. Grand job. Tip for future. Use a diluted bleach cleaner after a cutting session . Stops possible infection passing from hedge to hedge
That intro music puts the fear into you. I haven't felt that since Jaws! :D
Best video I’ve found on this! How often do you grease the gearbox via the screw hole, and what grease do you use? Thanks
I've done this and it’s a pain in the arse. I always have loose parts when doing this. This is why I prefer using a Dremmel tool or a grinder at slow speed to just sharpen the blades without getting into the gear box
Great job Jason, it's a time consuming job sharpening hedge cutter blades as i do my own too.
@jasongardener3425
3 жыл бұрын
Yes definitely, but a file is for me the best way, I do on sometimes use a sanding pad, when really busy and time is a issue for me, but file is perfect 👍
Thanks for posting the video. It was a help getting mine back together again. I used motorcycle chain lube between the blades, going to see how well that works.
@jasongardener3425
2 жыл бұрын
Cool 😊👍
Really enjoyed the video and your teaching style. I file old school crosscut saws and like to modify my flat files with an angle grinder to round off the sharp corners and not put a nick in the saw plate. With a safe file you can rub the curved part as a guide to make filing fast and accurate. Saw filers use felt markers on teeth to insure proper angle when filing. Ink is cheap. Quick question, I used chainsaw bar oil as a lubricant since it's anti-fling but don't know if it can harm plants.
Nice video Jason. Good to know how to do that. 👍👍👍👍👍🇺🇸
Beautiful! I wish I could make a blade look that good. I have a hard time maintaining the factory angle. Same problem I have with scissors. You make it look so easy.
@jasongardener3425
5 ай бұрын
Thank you, the trick is to not rush. 👍👍
Nice video jason i did a sthil km94rc cutter today i use a grinder with a well used flappy disc that is rounded of at the edges that does the round bits easy on a slow speed and i had to replace 2 connecting rods where one had the bearings come out
Great video loved it! I'm looking forward to doing this!
@jasongardener3425
2 ай бұрын
🙂👍
Very satisfying sharpening blades with a file.
@jasongardener3425
Жыл бұрын
Thanks 👍😀
This the best video I have seen thank you so much
@jasongardener3425
2 жыл бұрын
😀👍👍
Exceedingly good craftsmanship.
Great time of the year clean and sharpen and put away ready to go ! Well worth the effort if you know the cost of these hedge trimmers blades £75 for a good set. But Also good to have spares sharp on the shelf .
I must have missed this one somehow 🤔 . Very informative 👏 👌.
Love the video, I use a strop after every use you can buy round strops for mowers there about the same size as a chainsaw file. I also clean the tool to prevent any cross contamination of diseases between plants. Super important with chain saws and pruning saws.
@jasongardener3425
2 жыл бұрын
😀👍
Nice one Jason. Many thanks.
Great video Jason,very Informative 👌🏼
Fantastic. I fancy giving that a go!
A very good tutorial and thorough in every respect I enjoyed this immensely.
@jasongardener3425
2 жыл бұрын
Thank you very much 😀👍
Good video Jason👍 I cheat on mine and use a grinder, used to hand fill but took to long. The blades look identical to Stihls and internals much the same. I see the needle bearings in the con rod are different. Do they last longer? I've got 8 Stihl sets sharpened just got to sand and reassemble. Then I just swap blades through the season, can't use dull blades!😪 👍
Followed this verbatim. Worked perfectly. Many thanks.
@jasongardener3425
Жыл бұрын
😀👍
They look very sharp. I do the same with disassembling/assembling the blades. But I sand both sides of the blades with a sander. Then I place the blades on a working bench and use an air grinder to sharpen the teeth. I use the dirt on the teeth as marker for the correct angle.
@bumpkinrocks
4 жыл бұрын
I do exactly the same👍
@smartcatcollarproject5699
3 жыл бұрын
Just curious, I don't even own a compressor, but can you invert the rotation on an air grinder ?
Great video! Do you have to take the blades apart to sharpen or can you do them while attached to the head?
Thanks for putting this up mate, big help. Cheers
That was a great job I liked watching that.
@jasongardener3425
3 жыл бұрын
Cheers mate 😀👍
Excellent presentation. Now I know what to do. Cheers to you.
Great video. Thanks from Spain.
@jasongardener3425
14 күн бұрын
@@cesarblanco thank you 😊
Nice one... found that very helpful. Thanks to YOU
Hi, thank you so much for your tutorial. I have a question: the flat file is a second cut or smooth cut? Thanks.
Thanks men that was the best video I ever see 👍👍
@jasongardener3425
3 жыл бұрын
Thanks mate 👍👍
Try a die grinder, they can get the insides and get everything in very little time. Its even faster and leaves better results than a dremel. Ill bet i can sharpen a 24" in 5-10 mins tops, then switch pads to a non abrasive to polish the top if needed/desired. I will say you did a very clean and nice job, just to long for myself.
Thorough job indeed 👍
Beautifully done sir, yes sharpening and cleaning things is relaxing. ^_^
Thanks for that Jason, I think that's my Sunday afternoon taken care of! I seem to remember you mention that you make adapt/shorten your shafts for the long reach? I've been trying to suss out how to do it on a kombi, any chance of some pointers before I cock mine up? 😂 Hope your doing OK in the current situation and all the best👍
Seriously nice job!
Thanks for this. Appreciate it.
Nice educational video pal..am guilty of using a electric grinder, purely down to time like you say. Hope your keeping busy 👍
well in depth- great video.
@jasongardener3425
3 жыл бұрын
👍
Great job - will give it a go knowing this is very thorough. Apart from elbow grease - what sort of grease do you use in the tub - I usually grease with Stihl on the grease point but interested to know alternatives
@jayellis2939
Жыл бұрын
Same question l had.I Bought a tube of stihl but misplaced it.
quick questions lol but do you empty all your machines of fuel for storage in winter or is the fuel good to go all year around? need to service my hedge cutter, do you recommend a half round file for the corner bits? what brand files do you recommend? great video btw, very chilled and informative 👍🏻
I’m using a dremel (micro-grinder) the results are good but not this good I guess. However it takes way less time to do it. Great video btw I would love to see more tool-maintenance video from you maybe how you properly sharpen and maintain your pruning tools?
@smartcatcollarproject5699
3 жыл бұрын
I suppose the main difference is that your blades may last longer this way, as you can work with more precision than a dremel or a grinder ? That said mine has 21 teeth, that's 160+ faces to file, and I'm not sure I'll finish that work by hand ! Maybe I need a larger file, like in the video...
Hi Jason great video very interesting 👍i never took one to bits as yet 👍are you busye now the season is up and running 👍
Beautifully done. Very nice video too. M
Great video jason that is a great idea with chainsaw file
That was useful thanks 👍🏽
Great video, well explained. Very sharp, excuse the pun. As good as new.
my blades gum up too easily. I use the Stihl cleaner, but I thin it actually makes it worse. What are people using to keep their blades clean and lubricated after each use?
Question - if you are sharpening a machete with a flat file like you have on the video, do you push the file perpendicular to the blade (with the back end of file raised to match the bevel angle of the blade)? Or are you supposed to turn the file until the cutting lines on the file are parallel with the machete's blade edge, and then push forward? Was wondering why the lines are running at an angle on the file. I just bought a flat file 2 pack and have no idea how to correctly use it to sharpen.
solid job.
What do you use to lubricate the blades and how often do you do it?
😀 A great video chap - So important to keep those blades sharp. Bootiful work 👏🏻
Excellent video. Only wish the customers had their gasket replaced with that moisture
“Wear gloves... one slip and it’s gonna hurt” oh yesss indeed. I did mine last year for the first time, total pain in the rear, may give it another go as they’re all manky between the blades. Blades nearest machine are still pretty decent but blades nearer the tip, not so great.
Thanks a lot!!!
Really helpful. Thank you.
@jasongardener3425
3 жыл бұрын
👍
Good work my man
Great job there 👍, some of the con rod bearings in the stihl gearboxes can be a bit of a nightmare if you're not used to doing them but you have done a good job of those for sure.
How often do you perform such servicing on the practice? Thank you.
the good thing about taking it apart to sharpen the blades is that you can apply fresh grease at the same time I suppose; but getting back together correctly is imperative if it is going to work.
@ 8:35 I would of never thought of decking the blades. As you flatten them out from knicks the process is called decking. Like what engine cylinder heads and blocks are normally done to during a rebuild. Now I see the need for disassembly. I'll continue the video so you wont have 10 comments to read. You already have 2 from me. Now it's your turn to learn. WD-40 and similar solvents will be bounced off your head if pulled out in an American machine shop. By best friend is a machinist that makes the tooling that makes artificial limbs and organs. Solvents like WD-40 collect a massive amount of dirt, grit, and every thing you don't want in a cutting tool. Yeah I know that is a hard pill to swallow but it's true. Do I still use it. YES!!! But I hide everything like it when I know he is coming for a visit. Garden tools that I have sprayed off with a water hose will always get a healthy dose of WD-40 or similar rust prevention lubricant. now lets see what else is in the video. I'm writing as I come across parts of your video. So I don't know what's next. I'm truly being honest. And that is almost impossible to find now days. RE- Assembly? I would never use 3&1 oil. I prefer using the thickest Royal Purple engine oil. I even use it while doing machine work. @ 12:36 I use waterproof High temp grease for the gearbox and Bar and Chain saw oil for the blades before and after I use the tool. OH Hell man I just did that. I tightened everything up and the blades wouldn't move. I will try to find the proper torque setting for my tool. I hope you read all this. I took a 13:48 video and made it 4 times longer. I learned a lot. I hope you will as well.
Great video
Well I think I can safely say that the job could physically not be done better than that, and Jason is a FKN perfectionist maniac.
@jasongardener3425
Жыл бұрын
Cheers mate 👍
Wonderfully entertaining
Great job 🙂
@jasongardener3425
2 жыл бұрын
😀👍
Very nice instructions
@jasongardener3425
Жыл бұрын
Thank you 👍
Do you have a link on both the files you used ? Can I get them at Amazon?. Great video by the way keep it up 👍
Nice work 👍
You don't really have to time the whole blade just see how long you take over X amount of teeth divide that time by the amount of teeth you did and then multiply by how many teeth there are. I always thought u need a grinder because my old workplace did it that way but I'm happy to see I can use a simple file. I always enjoyed using a classic hand tool
Hi Jason, Thanks for your film! but I can't understand why any one would sharpen any tool towards the leading edge I have been sharpening tools for over 65years starting life in a joiners shop and other trades requiring sharp tools and other implements as well as my own tools. When you have sharpened your blades and turned them over and scoured them for want of a better word all you are doing is transferring the burr that you created in the first place by honing towards and under the leading edge. I suppose that's good enough for (rough arse gardening tackle) as most people would call it! not a precision cabinet maker and or musical instrument makers tools (look at Ray Mears films and tackle for sharpening his bush Knifes and axes!) for my gardening cutters I use a Diamond file sharpening from underneath the blade away from the leading edge and a half round file for the curves and to remove the burr a hardwood block with some lube rubbed over the cutting edge on the end grain job done. As for cleaning I submerge my cutters in a soil pipe filled with diesel run for a bit and dried off and at laying of time some sack cloth with a bit of light oil Job done and I've had the same cutters 25 years no probs!!! But if it works for you good, and anyone else who doesn't know how to sharpen up properly fair enough, but I cringe when I see it! It reminds me when as joiners, we used to get 15 mins sharpening up time before everyone else finished work If we had have been seen sharpening up like that we would have got peddled (on your bike kid) But thanks again.
@daveh1081
Жыл бұрын
Jonathan......that's an interesting take on sharpening. I always took an interest in metalwork at school and I still love to learn stuff like that. So always sharpen AWAY from the leading edge, right? I get the logic yet it still feels "wrong" somehow but I'm going to try it. Wow......every day really is a school day! 👍👍
Thanks Jason jimmy Aust
@jasongardener3425
Жыл бұрын
👍👍
Nice job
very meticulous....i do like.
@jasongardener3425
3 жыл бұрын
👍
nice one!
Wish I had the patience to do that. I just pay to get them sharpened.
Brilliant job how often you sharpen the blade's ?
@jasongardener3425
4 жыл бұрын
Thanks mate, a total strip down is once or twice a year, but I give a light run over with a file, probably even 4 or 5 weeks in general 👍
@simonparry3823
4 жыл бұрын
@@jasongardener3425 thanks on that need to file a bit more in the cutting season 👊
Yeah, wear gloves. Sliced hands with a dirty blade are a ready disaster. Great vid covering all the aspects of the blades. Cheers.
You should be using a small half round file mate!!!!
Quality 👍👍
ya i really did not know untail now , so thanks. t.
What type of Grease