HARLEY DAVIDSON TOURING SADDLEMEN STEP UP SEAT INSTALL
I installed a Saddlemen Step Up seat on my 2022Harley Davidson Road Glide ST PART NUMBER: 808-07B-195 TOUR STEP UP LS FRONT & REAR FLHR, FLHT, FLHX & FLTR
Жүктеу.....
Пікірлер: 50
@TMbiker1000 Жыл бұрын
I usually use a long zip tie to help put in the seat nut from under the fender.
@bangbangbikergang5052
Жыл бұрын
Brilliant. That makes a lot more sense. Hahaha
@tylermardyla295
Жыл бұрын
I also use a long piece of wire and tie the nut to it an pull it through, works like a dream!
@Dgroz
Жыл бұрын
Yep, zip tie or a cable feeder or some wire will do ...
@JayJay-nm9vmАй бұрын
Drop an end of a string (550 cord) from the top of the fender through the hole. Attach seat bolt by threading the string/cord through and tying a square knot. Pull seat bolt up through hole.
@6969curtis
Ай бұрын
it was painful to watch him doing it lmao....string 123 ....i usually tie a nut to the string an drop it out after install
@Ben-un3gk Жыл бұрын
I was looking for a video on how to remove the seat! Just picked up a 2023 rgst! GANG GANG BIKER GANG
@bangbangbikergang5052
Жыл бұрын
Dude you're going to love it. Bang Bang for life!
@davesleyer9393 Жыл бұрын
Thanks for the video. I’ve been dying to get one for my road king and after 14 weeks it’s finally here
@bangbangbikergang5052
Жыл бұрын
Awesome! Did you put it on yet? Super comfy. I still love mine. Thanks for watching. Cheers
@davesleyer9393
Жыл бұрын
@@bangbangbikergang5052 almost 200 miles on it. It fit great but damn that was a long wait
@user-px3cg2kp9q8 ай бұрын
Thank you for the great video from used sg st.
@saddlemenusa Жыл бұрын
Looks great on the bike!
@bangbangbikergang5052
Жыл бұрын
Thanks. You guys make quality seats. Still in love.
@saddlemenusa
Жыл бұрын
@@bangbangbikergang5052 Appreciate that big time!
@BourbonBagger Жыл бұрын
bro, in the future if you ever need to do this again, run a longer zip tie through the middle of the screw. Then pull it up through the hole and it makes it a 30sec job. it was painful to watch the stuggle! lol good build so far!
@bangbangbikergang5052
Жыл бұрын
That would be way easier. Cheers
@RoysMotoVentures Жыл бұрын
Nice video. 👍I would have been swearing up a storm, trying to get that seat nut up in the fender. 🤣🤣
@bangbangbikergang5052
Жыл бұрын
Oh I was. Since this video I’ve gotten a jack and the helps a bunch.
@OSOFLHP
Жыл бұрын
A piece of wire down from the top attach the nut to the wire and pull it up into place, push the wire back down or just clip it, takes less than a minute, zip tie works but you have to get it through the hole from the bottom,
@andrewcobarrubia95293 ай бұрын
You can leave the original seat mount on. Just in case you ever want to run the solo seat
@bangbangbikergang5052
2 ай бұрын
Damn dude! I was just thinking about the solo seat and now I don’t have the mounting hardware. Thanks for the heads up.
@thelost_woods
2 ай бұрын
I'm in the same seat situation. So are you saying just put the nuts back on the original bolts and throw the new seat on over top of them and that's alright?
@heybruh3274 Жыл бұрын
I am surprised that a UTuber doesn’t use UTube to see the many other videos that show this same topic. Hey, but then it’d only be an honest two minute video eh? Have a great day Champ
@bangbangbikergang5052
Жыл бұрын
Thanks for watching Pal. I appreciate it.
@BillsBigbreakssportscards-cj5e6 ай бұрын
Hey brother dose that seat make you feel low to the ground i short thats why i ask that question ?
@DugansDemos5 ай бұрын
Very ingenious workaround brother. Thanks for sharing. How do you like the seat after having it for a riding season or so? Break in period time? Are you still using it? How’s the passenger comfort? Sorry I send this message 2 minutes before you addressed my questions haha. Passenger comfort good tho?
@bangbangbikergang5052
5 ай бұрын
I've since learned that you use a long zip tie to feed the nut into the hole. 🤣The seat is still very comfortable as far as passenger my wife hasn't been on yet. Cheers and thanks for watching.
@DugansDemos
5 ай бұрын
@@bangbangbikergang5052 appreciate it
@erikwhitley413 Жыл бұрын
The one thing I wanted to see was how to get the solo seat bolts out... but ya skipped it 😭
@bangbangbikergang5052
Жыл бұрын
I didn't but my gopro did. LOL. thanks for watching. Cheers
@Bagrman-kt1ot Жыл бұрын
I hit sub button👍
@bangbangbikergang5052
Жыл бұрын
Thanks for the sub!
@cancelchannel3394 Жыл бұрын
I like the the original seat better 😊
@bangbangbikergang5052
11 ай бұрын
Nothing wrong with the original seat. I will say this one rides a little more comfy though. Cheers
@ramezy0410 ай бұрын
how is the height in between the legs I have the same bike and i'm happy with Stock seat height but want something more comfortable
@hankhamern5456 Жыл бұрын
Zip tie works on the fender screw bolt deal
@bangbangbikergang5052
Жыл бұрын
Yeah what the heck was i thinking. LOL
@meanf1502 Жыл бұрын
I ordered my saddleman seat an the security seat set them clowns sold me the wrong bolt with the kit the stock bolt is 1/4x20x1 inch an the bolt with the kit is way bigger
@willknott4796 Жыл бұрын
I like the shirt👍 FJB
@bangbangbikergang5052
Жыл бұрын
Excuse me? I'm sure you meant LOVE the shirt. LOL Cheers and thanks for watching.
@DouglasWilson-hh3wi Жыл бұрын
Looks great! I also have a gun ship gray bike. What color stitch did you order?
@bangbangbikergang5052
Жыл бұрын
Well Im a little late to the party. Its the grey stitching. Doesnt pop as much as i thought it would. Looks great though. I might try and match the stitching to the wheels like I did with the saddlemen logo. Thanks for watching. Cheers
@MrChrysler27 Жыл бұрын
What is the name of the nut set package? I need to order one for my bike it didn’t come with my seat
@bangbangbikergang5052
Жыл бұрын
saddlemen.com/atab-security-seat-screw-black. and thanks for watching
@bikelifetoot2457 Жыл бұрын
Zip tie buddy
@bangbangbikergang5052
Жыл бұрын
I coud have used that wisdom. Now I can spread the word. Thanks for watching. Cheers
@jeremyswaney4193 Жыл бұрын
ZipTie
@OSOFLHP Жыл бұрын
Painfull watching the fender nut install, fish it in, people say zip tie, I like stiff wire, sit on the seat in the garage then tell me it’s great, how about at the end of a 500 mile day, it’s a touring seat,
@bangbangbikergang5052
Жыл бұрын
Dude, the seat is solid. The furthest I've gone is 400 kinda had a hot spot but it was hot as F and super Humid. (swollen pig lips) I'm sure the Road Sofa would get you to where you need to be.
Пікірлер: 50
I usually use a long zip tie to help put in the seat nut from under the fender.
@bangbangbikergang5052
Жыл бұрын
Brilliant. That makes a lot more sense. Hahaha
@tylermardyla295
Жыл бұрын
I also use a long piece of wire and tie the nut to it an pull it through, works like a dream!
@Dgroz
Жыл бұрын
Yep, zip tie or a cable feeder or some wire will do ...
Drop an end of a string (550 cord) from the top of the fender through the hole. Attach seat bolt by threading the string/cord through and tying a square knot. Pull seat bolt up through hole.
@6969curtis
Ай бұрын
it was painful to watch him doing it lmao....string 123 ....i usually tie a nut to the string an drop it out after install
I was looking for a video on how to remove the seat! Just picked up a 2023 rgst! GANG GANG BIKER GANG
@bangbangbikergang5052
Жыл бұрын
Dude you're going to love it. Bang Bang for life!
Thanks for the video. I’ve been dying to get one for my road king and after 14 weeks it’s finally here
@bangbangbikergang5052
Жыл бұрын
Awesome! Did you put it on yet? Super comfy. I still love mine. Thanks for watching. Cheers
@davesleyer9393
Жыл бұрын
@@bangbangbikergang5052 almost 200 miles on it. It fit great but damn that was a long wait
Thank you for the great video from used sg st.
Looks great on the bike!
@bangbangbikergang5052
Жыл бұрын
Thanks. You guys make quality seats. Still in love.
@saddlemenusa
Жыл бұрын
@@bangbangbikergang5052 Appreciate that big time!
bro, in the future if you ever need to do this again, run a longer zip tie through the middle of the screw. Then pull it up through the hole and it makes it a 30sec job. it was painful to watch the stuggle! lol good build so far!
@bangbangbikergang5052
Жыл бұрын
That would be way easier. Cheers
Nice video. 👍I would have been swearing up a storm, trying to get that seat nut up in the fender. 🤣🤣
@bangbangbikergang5052
Жыл бұрын
Oh I was. Since this video I’ve gotten a jack and the helps a bunch.
@OSOFLHP
Жыл бұрын
A piece of wire down from the top attach the nut to the wire and pull it up into place, push the wire back down or just clip it, takes less than a minute, zip tie works but you have to get it through the hole from the bottom,
You can leave the original seat mount on. Just in case you ever want to run the solo seat
@bangbangbikergang5052
2 ай бұрын
Damn dude! I was just thinking about the solo seat and now I don’t have the mounting hardware. Thanks for the heads up.
@thelost_woods
2 ай бұрын
I'm in the same seat situation. So are you saying just put the nuts back on the original bolts and throw the new seat on over top of them and that's alright?
I am surprised that a UTuber doesn’t use UTube to see the many other videos that show this same topic. Hey, but then it’d only be an honest two minute video eh? Have a great day Champ
@bangbangbikergang5052
Жыл бұрын
Thanks for watching Pal. I appreciate it.
Hey brother dose that seat make you feel low to the ground i short thats why i ask that question ?
Very ingenious workaround brother. Thanks for sharing. How do you like the seat after having it for a riding season or so? Break in period time? Are you still using it? How’s the passenger comfort? Sorry I send this message 2 minutes before you addressed my questions haha. Passenger comfort good tho?
@bangbangbikergang5052
5 ай бұрын
I've since learned that you use a long zip tie to feed the nut into the hole. 🤣The seat is still very comfortable as far as passenger my wife hasn't been on yet. Cheers and thanks for watching.
@DugansDemos
5 ай бұрын
@@bangbangbikergang5052 appreciate it
The one thing I wanted to see was how to get the solo seat bolts out... but ya skipped it 😭
@bangbangbikergang5052
Жыл бұрын
I didn't but my gopro did. LOL. thanks for watching. Cheers
I hit sub button👍
@bangbangbikergang5052
Жыл бұрын
Thanks for the sub!
I like the the original seat better 😊
@bangbangbikergang5052
11 ай бұрын
Nothing wrong with the original seat. I will say this one rides a little more comfy though. Cheers
how is the height in between the legs I have the same bike and i'm happy with Stock seat height but want something more comfortable
Zip tie works on the fender screw bolt deal
@bangbangbikergang5052
Жыл бұрын
Yeah what the heck was i thinking. LOL
I ordered my saddleman seat an the security seat set them clowns sold me the wrong bolt with the kit the stock bolt is 1/4x20x1 inch an the bolt with the kit is way bigger
I like the shirt👍 FJB
@bangbangbikergang5052
Жыл бұрын
Excuse me? I'm sure you meant LOVE the shirt. LOL Cheers and thanks for watching.
Looks great! I also have a gun ship gray bike. What color stitch did you order?
@bangbangbikergang5052
Жыл бұрын
Well Im a little late to the party. Its the grey stitching. Doesnt pop as much as i thought it would. Looks great though. I might try and match the stitching to the wheels like I did with the saddlemen logo. Thanks for watching. Cheers
What is the name of the nut set package? I need to order one for my bike it didn’t come with my seat
@bangbangbikergang5052
Жыл бұрын
saddlemen.com/atab-security-seat-screw-black. and thanks for watching
Zip tie buddy
@bangbangbikergang5052
Жыл бұрын
I coud have used that wisdom. Now I can spread the word. Thanks for watching. Cheers
ZipTie
Painfull watching the fender nut install, fish it in, people say zip tie, I like stiff wire, sit on the seat in the garage then tell me it’s great, how about at the end of a 500 mile day, it’s a touring seat,
@bangbangbikergang5052
Жыл бұрын
Dude, the seat is solid. The furthest I've gone is 400 kinda had a hot spot but it was hot as F and super Humid. (swollen pig lips) I'm sure the Road Sofa would get you to where you need to be.